T10 Torx screwdriver

VeriFinder Stabilization Module Replacement

Last Updated: 04/24/2025 1:42 AM

The following table lists all the components that make up the document.

Title Type Status Last Updated
Symetrica VeriFinder SN-20
Device
Published
10/28/2024 3:35 PM
5710 - 5270 - Remove battery; Remark:
Procedure Step
Published
11/03/2022 12:30 PM
5270 - Remove battery
Instruction
Published
10/17/2022 2:02 PM
6191 - 6190 - Unclasp and open battery compartment; Remark:6195
Procedure Step
Published
11/19/2022 6:04 PM
6190 - Unclasp and open battery compartment
Instruction
Published
11/19/2022 6:03 PM
6195 - IO VeriFinder Opening Battery Latch CCW
Remark
Published
11/12/2024 9:15 PM
6192 - 1816 - Remove battery; Remark:6189
Procedure Step
Published
11/19/2022 6:05 PM
1816 - Remove battery
Instruction
Published
11/20/2020 9:29 AM
6189 - Lift by tab.
Remark
Published
11/19/2022 6:05 PM
6193 - 6188 - Close and reclasp battery compartment.; Remark:6194
Procedure Step
Published
11/19/2022 6:05 PM
6188 - Close and reclasp battery compartment.
Instruction
Published
11/19/2022 6:05 PM
6194 - IO VeriFinder Close Lid on Battery NO Pack
Remark
Published
11/12/2024 9:16 PM
6074 - 6073 - Disassemble VeriFinder; Remark:
Procedure Step
Published
11/18/2022 3:00 PM
6073 - Disassemble VeriFinder
Instruction
Published
11/18/2022 3:00 PM
6172 - 6171 - Remove rubber boot; Remark:6170
Procedure Step
Published
11/19/2022 5:42 PM
6171 - Remove rubber boot
Instruction
Published
11/19/2022 5:41 PM
6170 - Separate boot edges from top sides of VeriFinder. Pull back on rear of boot a...
Remark
Published
11/19/2022 5:42 PM
6173 - 6169 - Remove four (4) rear cover screws; Remark:6168
Procedure Step
Published
11/19/2022 5:45 PM
6169 - Remove four (4) rear cover screws
Instruction
Published
11/19/2022 5:44 PM
6168 - Use a T10 Torx screwdriver. Retain screws.
Remark
Published
11/19/2022 5:44 PM
6174 - 6167 - Remove two (2) USB [Universal Serial Bus] jack screws; Remark:6166
Procedure Step
Published
11/19/2022 5:46 PM
6167 - Remove two (2) USB [Universal Serial Bus] jack screws
Instruction
Published
11/19/2022 5:45 PM
6166 - Use a T6 Torx screwdriver. Retain screws.
Remark
Published
11/19/2022 5:46 PM
6175 - 6165 - Remove charging port nut and washer; Remark:6164
Procedure Step
Published
11/19/2022 5:47 PM
6165 - Remove charging port nut and washer
Instruction
Published
11/19/2022 5:47 PM
6164 - Use a 10 mm nut driver. Retain nut and washer.
Remark
Published
11/19/2022 5:47 PM
6185 - 6182 - Remove rear cover; Remark:6181
Procedure Step
Published
11/19/2022 5:53 PM
6183 - Caution : Internal components are sealed with RTV adhesive. Use care when separating se...
Annotation
Published
11/19/2022 5:53 PM
6184 - Note : Upon removing the rear case, there is a flat washer under the headphone jack ...
Annotation
Published
11/19/2022 5:53 PM
6182 - Remove rear cover
Instruction
Published
11/19/2022 5:51 PM
6181 - Set aside cover.
Remark
Published
11/19/2022 5:52 PM
6186 - 6180 - Remove six (6) bottom cover screws; Remark:6179
Procedure Step
Published
11/19/2022 5:55 PM
6180 - Remove six (6) bottom cover screws
Instruction
Published
11/19/2022 5:54 PM
6179 - Use a T10 Torx screwdriver. Retain screws.
Remark
Published
11/19/2022 5:54 PM
6187 - 6177 - Separate top and bottom enclosures; Remark:6176
Procedure Step
Published
11/19/2022 5:58 PM
5291 - Note : It is good practice to verify all cables and connectors are labeled prior to ...
Annotation
Published
10/24/2022 8:35 AM
6178 - Note : Ensure the six (6) black O-rings are retained in place when separating enclos...
Annotation
Published
11/19/2022 5:58 PM
6177 - Separate top and bottom enclosures
Instruction
Published
11/19/2022 5:55 PM
6176 - Disconnect two (2) cables prior to separating enclosures.
Remark
Published
11/19/2022 5:56 PM
6072 - 6071 - Uninstall Faulty Stabilization Module; Remark:
Procedure Step
Published
11/18/2022 3:00 PM
6071 - Uninstall Faulty Stabilization Module
Instruction
Published
11/18/2022 3:00 PM
6160 - 6159 - Disconnect stabilization module cable; Remark:6158
Procedure Step
Published
11/19/2022 5:11 PM
6152 - Warning : Do not disassemble the stabilization source module. The expired stabilization...
Annotation
Published
11/19/2022 5:05 PM
1345 - Note : It is good practice to ensure all cables and connectors are labeled prior to ...
Annotation
Published
10/04/2022 11:08 AM
6159 - Disconnect stabilization module cable
Instruction
Published
11/19/2022 5:09 PM
6158 - IO VeriFinder Disconnect Cable to Stabil Module
Remark
Published
11/12/2024 9:17 PM
6161 - 5387 - Remove Styrofoam covers; Remark:6157
Procedure Step
Published
11/19/2022 5:14 PM
5387 - Remove Styrofoam covers
Instruction
Published
10/27/2022 3:20 PM
6157 - IO VeriFinder Open Styrofoam
Remark
Published
11/12/2024 9:19 PM
6162 - 6156 - Remove stabilization module; Remark:6155
Procedure Step
Published
11/19/2022 5:15 PM
6156 - Remove stabilization module
Instruction
Published
11/19/2022 5:14 PM
6155 - Gently separate from Styrofoam.
Remark
Published
11/19/2022 5:15 PM
6163 - 6154 - Remove cable from stabilization module; Remark:6153
Procedure Step
Published
11/19/2022 5:17 PM
6154 - Remove cable from stabilization module
Instruction
Published
11/19/2022 5:16 PM
6153 - IO VeriFinder Remove Cable from Stabil Module
Remark
Published
11/12/2024 9:21 PM
5350 - 5349 - Install New Stabilization Module; Remark:
Procedure Step
Published
10/27/2022 1:29 PM
5349 - Install New Stabilization Module
Instruction
Published
10/27/2022 1:29 PM
6148 - 6147 - Connect cable; Remark:6146
Procedure Step
Published
11/19/2022 2:54 PM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.
Annotation
Published
10/28/2022 2:19 PM
6147 - Connect cable
Instruction
Published
11/19/2022 2:52 PM
6146 - Connect stabilization module cable to new stabilization module.
Remark
Published
11/19/2022 2:54 PM
6149 - 6145 - Record component Information; Remark:6144
Procedure Step
Published
11/19/2022 2:57 PM
6145 - Record component Information
Instruction
Published
11/19/2022 2:55 PM
6144 - Record in the Corrective Maintenance Report the date and activity printed on ...
Remark
Published
11/19/2022 2:56 PM
6150 - 6143 - Insert component; Remark:6142
Procedure Step
Published
11/19/2022 2:58 PM
6143 - Insert component
Instruction
Published
11/19/2022 2:57 PM
6142 - Insert stabilization module into Styrofoam and reseat over gamma detector.
Remark
Published
11/19/2022 2:58 PM
6151 - 6141 - Reconnect cable; Remark:6140
Procedure Step
Published
11/19/2022 2:59 PM
6141 - Reconnect cable
Instruction
Published
11/19/2022 2:58 PM
6140 - Reconnect stabilization module cable to circuit boards.
Remark
Published
11/19/2022 2:59 PM
6070 - 6069 - Reassemble VeriFinder; Remark:
Procedure Step
Published
11/18/2022 3:01 PM
6069 - Reassemble VeriFinder
Instruction
Published
11/18/2022 3:01 PM
6117 - 6116 - Reconnect two (2) cables; Remark:6115
Procedure Step
Published
11/19/2022 2:11 PM
5895 - Caution : Verify all wiring is inside the instrument while replacing cover.
Annotation
Published
11/07/2022 12:55 PM
6116 - Reconnect two (2) cables
Instruction
Published
11/19/2022 2:09 PM
6115 - Snap into place and secure top and bottom enclosures together.
Remark
Published
11/19/2022 2:11 PM
6118 - 6114 - Reinstall six (6) bottom cover screws; Remark:6113
Procedure Step
Published
11/19/2022 2:15 PM
569 - Caution : Do not overtighten screws.
Annotation
Published
06/16/2021 2:31 PM
6106 - Standard : Torque all screws to 1 N-m.
Annotation
Published
11/18/2022 4:22 PM
6114 - Reinstall six (6) bottom cover screws
Instruction
Published
11/19/2022 2:12 PM
6113 - Use a T10 Torx screwdriver.
Remark
Published
11/19/2022 2:13 PM
6119 - 6112 - Reseal top and bottom enclosures; Remark:6111
Procedure Step
Published
11/19/2022 2:17 PM
6107 - Caution : The enclosure must be properly sealed when it is reassembled.
Annotation
Published
11/18/2022 4:25 PM
6112 - Reseal top and bottom enclosures
Instruction
Published
11/19/2022 2:15 PM
6111 - Seal around entirety of VeriFinder where top and bottom enclosures join with ...
Remark
Published
11/19/2022 2:17 PM
6120 - 6110 - Reinstall headphone jack washer and charging port O-ring; Remark:6109
Procedure Step
Published
11/19/2022 2:19 PM
6110 - Reinstall headphone jack washer and charging port O-ring
Instruction
Published
11/19/2022 2:17 PM
6109 - IO VeriFinder Seals for Audio, Charging Ports
Remark
Published
11/12/2024 9:22 PM
6129 - 6128 - Set rear cover in place; Remark:6127
Procedure Step
Published
11/19/2022 2:34 PM
6128 - Set rear cover in place
Instruction
Published
11/19/2022 2:33 PM
6127 - IO VeriFinder Rear Cover 4 Screws
Remark
Published
11/12/2024 9:23 PM
6130 - 6126 - Reinstall charging port washer and nut; Remark:6125
Procedure Step
Published
11/19/2022 2:36 PM
6126 - Reinstall charging port washer and nut
Instruction
Published
11/19/2022 2:36 PM
6125 - IO VeriFinder Charting Port Rear
Remark
Published
11/12/2024 9:25 PM
6131 - 6124 - Reinstall two (2) USB port screws; Remark:6123
Procedure Step
Published
11/19/2022 2:37 PM
6124 - Reinstall two (2) USB port screws
Instruction
Published
11/19/2022 2:36 PM
6123 - Use a T6 Torx screwdriver.
Remark
Published
11/19/2022 2:37 PM
6137 - 6136 - Reinstall four (4) rear cover screws; Remark:6135
Procedure Step
Published
11/19/2022 2:43 PM
6136 - Reinstall four (4) rear cover screws
Instruction
Published
11/19/2022 2:42 PM
6135 - Use a T10 Torx screwdriver.
Remark
Published
11/19/2022 2:43 PM
6138 - 6134 - Reseal rear cover; Remark:6133
Procedure Step
Published
11/19/2022 2:45 PM
6134 - Reseal rear cover
Instruction
Published
11/19/2022 2:43 PM
6133 - Seal around entirety of VeriFinder rear cover with RTV.
Remark
Published
11/19/2022 2:44 PM
6139 - 6132 - Reinstall rubber boot; Remark:6103
Procedure Step
Published
11/19/2022 2:46 PM
6132 - Reinstall rubber boot
Instruction
Published
11/19/2022 2:45 PM
6103 - Insert front of VeriFinder into boot and rotate bottom end of VeriFinder down...
Remark
Published
11/18/2022 4:18 PM
6104 - Pull back the bottom of boot and push VeriFinder into boot.
Remark
Published
11/18/2022 4:19 PM
6105 - Secure top corners.
Remark
Published
11/18/2022 4:19 PM
6068 - 6067 - Reinstall Battery; Remark:
Procedure Step
Published
11/18/2022 3:02 PM
6067 - Reinstall Battery
Instruction
Published
11/18/2022 3:02 PM
6100 - 6099 - Unclasp and open battery compartment; Remark:6098
Procedure Step
Published
11/18/2022 4:12 PM
6099 - Unclasp and open battery compartment
Instruction
Published
11/18/2022 4:10 PM
6098 - IO VeriFinder Opening Battery Compartment Empty
Remark
Published
11/12/2024 9:10 PM
6101 - 4783 - INSERT battery; Remark:6097
Procedure Step
Published
11/18/2022 4:13 PM
4783 - INSERT battery
Instruction
Published
06/30/2022 5:38 PM
6097 -
Remark
Published
11/18/2022 4:13 PM
6102 - 6096 - Close and reclasp battery compartment; Remark:6095
Procedure Step
Published
11/18/2022 4:15 PM
6096 - Close and reclasp battery compartment
Instruction
Published
11/18/2022 4:14 PM
6095 - IO VeriFinder Close Lid on Battery Pack Compartment
Remark
Published
11/12/2024 9:11 PM
6066 - 6065 - Complete Stabilization; Remark:
Procedure Step
Published
11/18/2022 3:03 PM
6065 - Complete Stabilization
Instruction
Published
11/18/2022 3:03 PM
6088 - 220 - Power on instrument; Remark:6087
Procedure Step
Published
11/18/2022 3:15 PM
220 - Power on instrument
Instruction
Published
04/06/2025 7:00 PM
6087 - Hold down the Select button. The VeriFinder will initialize ...
Remark
Published
11/18/2022 3:15 PM
6089 - 6086 - Select information menu; Remark:6085
Procedure Step
Published
11/18/2022 3:17 PM
6086 - Select information menu
Instruction
Published
11/18/2022 3:16 PM
6085 - Navigate to the MENU using the LEFT arrow b...
Remark
Published
11/18/2022 3:17 PM
6090 - 6084 - Access system information; Remark:6083
Procedure Step
Published
11/18/2022 3:20 PM
6084 - Access system information
Instruction
Published
11/18/2022 3:18 PM
6083 - Press the SELECT button twice to enter System Inform...
Remark
Published
11/18/2022 3:19 PM
6091 - 6082 - Locate stabilization information; Remark:6081
Procedure Step
Published
11/18/2022 3:21 PM
6082 - Locate stabilization information
Instruction
Published
11/18/2022 3:20 PM
6081 - Use the DOWN arrow to scroll until reaching the Stabilizatio...
Remark
Published
11/18/2022 3:21 PM
6092 - 6080 - Confirm stabilization module date; Remark:6079
Procedure Step
Published
11/18/2022 3:23 PM
6080 - Confirm stabilization module date
Instruction
Published
11/18/2022 3:22 PM
6079 - Verify the activity and date displayed match what was printed on the installe...
Remark
Published
11/18/2022 3:23 PM
6093 - 6078 - Document stabilization information; Remark:6077
Procedure Step
Published
11/18/2022 3:23 PM
6078 - Document stabilization information
Instruction
Published
11/18/2022 3:23 PM
6077 - Include stabilization information in Corrective Maintenance Report.
Remark
Published
11/18/2022 3:23 PM
6094 - 319 - Perform operational test; Remark:6076
Procedure Step
Published
11/18/2022 3:25 PM
319 - Perform operational test
Instruction
Published
06/10/2021 8:31 PM
6076 - DET-HHD-SYM-VER-RM01, VeriFinder Operational Test.
Remark
Published
11/18/2022 3:25 PM
322 - 321 - Document maintenance actions; Remark:
Procedure Step
Published
06/17/2021 9:49 AM
321 - Document maintenance actions
Instruction
Published
04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866
Procedure Step
Published
06/18/2021 5:58 PM
2585 - Document maintenance performed
Instruction
Published
07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.
Remark
Published
04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864
Procedure Step
Published
06/29/2022 9:50 AM
4705 - Submit report
Instruction
Published
06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.
Remark
Published
07/28/2022 1:36 PM
Corrective Maintenance Procedure
Document Type
Published
03/02/2020 3:32 PM
minutes
Duration
Published
05/26/2022 11:41 AM
As Needed
Frequency
Published
04/01/2020 11:36 AM
Caution
Annotation Type
Published
03/02/2020 3:24 PM
Note
Annotation Type
Published
03/02/2020 3:25 PM
Warning
Annotation Type
Published
03/02/2020 3:25 PM
Standard
Annotation Type
Published
03/02/2020 3:25 PM
Technician 2
Skill Level
Published
04/09/2020 1:17 AM
T6 Torx screwdriver
Tools
Published
10/27/2022 1:17 PM
T10 Torx screwdriver
Tools
Published
11/10/2022 12:57 PM
10 mm nut driver
Tools
Published
11/10/2022 12:56 PM
Torque screwdriver (if available)
Tools
Published
11/10/2022 12:56 PM
Verifinder Battery Cover Open Latch CCW
படம்
Published
11/18/2022 3:57 PM
VeriFinder Battery Pack Remove
படம்
Published
02/19/2023 3:43 PM
Verifinder Battery Cover Closing NO Pack
படம்
Published
11/20/2022 11:31 AM
VeriFinder Boot Remove 1 Sides
படம்
Published
11/19/2022 5:38 PM
VeriFinder Boot Remove 2, 3 Rear Front
படம்
Published
11/19/2022 5:40 PM
VeriFinder 4 Screws Rear Cover
படம்
Published
11/19/2022 1:12 PM
VeriFinder 2 Screws USB Port Rear Cover
படம்
Published
11/19/2022 1:15 PM
VeriFinder Charging Port Rear Cover
படம்
Published
11/19/2022 1:19 PM
VeriFinder Seals Install Charging Audio Ports
படம்
Published
02/19/2023 3:55 PM
VeriFinder 6 Screws Bottom Cover
படம்
Published
11/19/2022 1:26 PM
VeriFinder Separate Top Bottom
படம்
Published
02/19/2023 3:46 PM
VeriFinder Cables Bottom to Top Remove
படம்
Published
02/19/2023 1:32 PM
VeriFinder Bottom 6 O-ring Locations
படம்
Published
02/19/2023 1:40 PM
VeriFinder Cable to Circuit Board Disconnect
படம்
Published
11/19/2022 4:43 PM
VeriFinder Styrofoam Open Arch Arrow
படம்
Published
02/19/2023 1:42 PM
VeriFinder Styrofoam Detector View Open
படம்
Published
11/19/2022 5:02 PM
verifinder_di_stabilmodule_remove.jpg
படம்
Published
02/19/2023 1:59 PM
VeriFinder Na-22 Module Cable Disconnect
படம்
Published
11/19/2022 4:56 PM
VeriFinder Na-22 Module Cable Connect
படம்
Published
11/19/2022 4:55 PM
VeriFinder Na-22 Module Activity Date Box
படம்
Published
11/19/2022 4:51 PM
VeriFinder Stabilization Module Install
படம்
Published
02/19/2023 2:01 PM
VeriFinder Cable to Circuit Board Connect
படம்
Published
02/19/2023 1:48 PM
VeriFinder Cables Top to Bottom
படம்
Published
02/19/2023 1:36 PM
VeriFinder Separate Top Bottom
படம்
Published
02/19/2023 3:48 PM
VeriFinder RTV Side Seal
படம்
Published
11/19/2022 1:10 PM
VeriFinder Rear Cover Insert 4 Arrow
படம்
Published
11/19/2022 1:21 PM
VeriFinder RTV Rear Seal
படம்
Published
11/19/2022 1:08 PM
VeriFinder Boot Install 1,2 Front
படம்
Published
11/18/2022 4:03 PM
VeriFinder Boot Install 3,4 Rear
படம்
Published
11/18/2022 4:06 PM
VeriFinder Boot Install 5 Sides
படம்
Published
11/18/2022 4:05 PM
Verifinder Battery Cover Open NO Pack
படம்
Published
11/18/2022 3:54 PM
Verifinder Battery Pack Align Polarity
படம்
Published
11/18/2022 3:51 PM
Verifinder Battery Pack Inserting
படம்
Published
11/18/2022 3:49 PM
Verifinder Battery Cover Closing
படம்
Published
02/19/2023 2:06 PM
VeriFinder POWER/SELECT button
படம்
Published
02/19/2023 3:51 PM
VeriFinder Start up Stabilizing Screen
படம்
Published
10/29/2020 8:25 PM
VeriFinder Menu Select Left Arrow
படம்
Published
11/18/2022 2:43 PM
VeriFinder Icon Information Select Down Arrow
படம்
Published
02/19/2023 1:57 PM
verifinder_di_menu_sysinfo_select_79cps
படம்
Published
02/19/2023 1:54 PM
VeriFinder System Information Menu Screen2.80
படம்
Published
02/19/2023 2:04 PM
VeriFinder Stabilization Info Screen
படம்
Published
02/19/2023 1:52 PM

PackEye Reseat Power Supply Connections

Last Updated: 04/24/2025 1:42 AM

The following table lists all the components that make up the document.

Title Type Status Last Updated
Thermo FHT1377 PackEye
Device
Published
10/28/2024 3:37 PM
5662 - 5661 - Uninstall Power Supply Module; Remark:
Procedure Step
Published
11/02/2022 5:10 PM
5661 - Uninstall Power Supply Module
Instruction
Published
11/02/2022 5:09 PM
5660 - 313 - Power off instrument; Remark:4086
Procedure Step
Published
04/07/2025 4:34 PM
313 - Power off instrument
Instruction
Published
07/23/2021 2:41 PM
4086 - Press and hold the power button for approximately 10 seconds until indicator ...
Remark
Published
05/02/2022 6:04 PM
5666 - 4222 - Place instrument on flat surface; Remark:4221
Procedure Step
Published
11/03/2022 8:17 AM
4222 - Place instrument on flat surface
Instruction
Published
05/10/2022 1:54 PM
4221 - Shoulder straps should be facing down.
Remark
Published
05/10/2022 1:55 PM
5667 - 3876 - Open top of backpack; Remark:5665
Procedure Step
Published
11/03/2022 8:21 AM
3876 - Open top of backpack
Instruction
Published
04/04/2022 3:14 PM
5665 - IO PackEye Open Top for Battery
Remark
Published
11/09/2024 8:06 PM
5668 - 4219 - Remove distribution box; Remark:4218
Procedure Step
Published
11/03/2022 8:22 AM
4219 - Remove distribution box
Instruction
Published
05/10/2022 1:58 PM
4218 - The distribution box is usually located in the top of the backpack.
Remark
Published
05/10/2022 1:58 PM
5669 - 4217 - Disconnect battery cable; Remark:4216
Procedure Step
Published
11/03/2022 8:47 AM
5664 - Note : The other cord connected to the distribution box is the headphone plug.
Annotation
Published
11/03/2022 8:47 AM
4217 - Disconnect battery cable
Instruction
Published
05/10/2022 2:01 PM
4216 - Rotate the collar counterclockwise and pull straight out. The battery cable c...
Remark
Published
05/10/2022 2:03 PM
5673 - 5672 - Disconnect RS232 jumper; Remark:5670
Procedure Step
Published
11/03/2022 9:07 AM
5672 - Disconnect RS232 jumper
Instruction
Published
11/03/2022 9:03 AM
5670 - Use small, slotted screwdriver.
Remark
Published
11/03/2022 9:07 AM
5671 - IO PackEye RS232 Disconnect Cable
Remark
Published
11/09/2024 8:07 PM
5680 - 5679 - Disconnect Bluetooth adapter cable; Remark:5670
Procedure Step
Published
11/03/2022 9:15 AM
5679 - Disconnect Bluetooth adapter cable
Instruction
Published
11/03/2022 9:12 AM
5678 - IO PackEye Cable for BTA Disconnect
Remark
Published
11/09/2024 8:08 PM
5681 - 5677 - Remove wire ties; Remark:5676
Procedure Step
Published
11/03/2022 9:27 AM
5677 - Remove wire ties
Instruction
Published
11/03/2022 9:16 AM
5676 - Note location of wire ties for reassembly. Use wire cutter or scissors.
Remark
Published
11/03/2022 9:27 AM
5770 - IO PackEye Power Cable Ties Location
Remark
Published
11/09/2024 8:08 PM
5682 - 5675 - Remove power supply module; Remark:5674
Procedure Step
Published
11/03/2022 9:35 AM
5675 - Remove power supply module
Instruction
Published
11/03/2022 9:31 AM
5674 - There are Velcro strips securing the power supply module to the FHT 681 ampli...
Remark
Published
11/03/2022 9:35 AM
5783 - 5782 - Inspect Internal Components; Remark:
Procedure Step
Published
11/03/2022 3:19 PM
5782 - Inspect Internal Components
Instruction
Published
11/03/2022 3:19 PM
5821 - 5309 - Remove two (2) screws; Remark:5819
Procedure Step
Published
11/04/2022 7:38 AM
5309 - Remove two (2) screws
Instruction
Published
10/24/2022 9:50 AM
5819 - Only remove the screws on the side with the charger connector. Use T-10 Torx ...
Remark
Published
11/04/2022 7:36 AM
5704 - IO PackEye Power Module Screws
Remark
Published
11/09/2024 8:09 PM
5822 - 5702 - Remove electronics; Remark:5818
Procedure Step
Published
11/04/2022 7:42 AM
5702 - Remove electronics
Instruction
Published
11/03/2022 10:50 AM
5818 - Components will slide out of the housing.
Remark
Published
11/04/2022 7:42 AM
5823 - 5817 - Inspect internal board for damage; Remark:5816
Procedure Step
Published
11/04/2022 7:46 AM
5817 - Inspect internal board for damage
Instruction
Published
11/04/2022 7:44 AM
5816 - Check for loose connections, burn marks, and debris. Check battery for leakag...
Remark
Published
11/04/2022 7:46 AM
5824 - 5815 - Inspect underside of circuit board; Remark:5814
Procedure Step
Published
11/04/2022 7:50 AM
5815 - Inspect underside of circuit board
Instruction
Published
11/04/2022 7:48 AM
5814 - Check for loose connections, burn marks, and debris. Check USB port for damag...
Remark
Published
11/04/2022 7:50 AM
5825 - 5813 - Disconnect spade connectors; Remark:5812
Procedure Step
Published
11/04/2022 7:55 AM
5813 - Disconnect spade connectors
Instruction
Published
11/04/2022 7:52 AM
5812 - If wires are soldered to the board, skip this step.
Remark
Published
11/04/2022 7:55 AM
5826 - 5811 - Reconnect spade connectors from battery to internal board; Remark:5810
Procedure Step
Published
11/04/2022 7:59 AM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.
Annotation
Published
10/28/2022 2:19 PM
5811 - Reconnect spade connectors from battery to internal board
Instruction
Published
11/04/2022 7:56 AM
5810 - Ensure the black wire is connected closest to the edge of the board.
Remark
Published
11/04/2022 7:58 AM
5827 - 5720 - Replace electronics; Remark:5719
Procedure Step
Published
11/04/2022 8:03 AM
5721 - Caution : Circuit board must be inserted correctly to prevent damage to components....
Annotation
Published
11/03/2022 1:15 PM
5720 - Replace electronics
Instruction
Published
11/03/2022 1:11 PM
5719 - Align circuit board with third slot from bottom of enclosure and slide into p...
Remark
Published
11/03/2022 1:15 PM
5828 - 5718 - Align gasket; Remark:5717
Procedure Step
Published
11/04/2022 8:06 AM
5718 - Align gasket
Instruction
Published
11/03/2022 1:16 PM
5717 - Verify gasket is aligned between housing and end panel before inserting screw...
Remark
Published
11/03/2022 1:18 PM
5829 - 5716 - Reinstall two (2) enclosure screws; Remark:5714
Procedure Step
Published
11/04/2022 8:09 AM
5716 - Reinstall two (2) enclosure screws
Instruction
Published
11/03/2022 1:19 PM
5714 - Use T-10 Torx screwdriver.
Remark
Published
11/03/2022 1:20 PM
5780 - 5779 - Reinstall Power Supply Module; Remark:
Procedure Step
Published
11/03/2022 1:25 PM
5779 - Reinstall Power Supply Module
Instruction
Published
11/03/2022 1:25 PM
5834 - 5775 - Secure power supply module to FHT 681; Remark:5774
Procedure Step
Published
11/04/2022 9:29 AM
5775 - Secure power supply module to FHT 681
Instruction
Published
11/03/2022 2:46 PM
5774 - The module will snap into place.
Remark
Published
11/03/2022 2:50 PM
5835 - 5773 - Reconnect battery cable; Remark:5772
Procedure Step
Published
11/04/2022 9:30 AM
5773 - Reconnect battery cable
Instruction
Published
11/03/2022 2:51 PM
5772 - Align the connector and push in. Rotate collar clockwise and hand-tighten.
Remark
Published
11/03/2022 2:55 PM
5836 - 5771 - Install wire ties; Remark:5769
Procedure Step
Published
11/04/2022 9:33 AM
5771 - Install wire ties
Instruction
Published
11/03/2022 2:56 PM
5769 - If desired, install new wire ties and cut off excess.
Remark
Published
11/03/2022 3:05 PM
5837 - 4237 - Replace distribution box; Remark:4236
Procedure Step
Published
11/04/2022 9:43 AM
4237 - Replace distribution box
Instruction
Published
05/10/2022 2:15 PM
4236 - IO PackEye Distro Box Install
Remark
Published
10/24/2024 6:53 PM
5838 - 5788 - Reconnect Bluetooth adapter cable; Remark:5787
Procedure Step
Published
11/04/2022 9:45 AM
5788 - Reconnect Bluetooth adapter cable
Instruction
Published
11/03/2022 3:17 PM
5787 - IO PackEye Cable for BTA Connect
Remark
Published
11/09/2024 8:13 PM
5839 - 5786 - Reconnect RS232 jumper; Remark:5670
Procedure Step
Published
11/04/2022 9:49 AM
5786 - Reconnect RS232 jumper
Instruction
Published
11/03/2022 3:39 PM
5830 - IO PackEye RS232 Connect Cable
Remark
Published
11/09/2024 8:14 PM
322 - 321 - Document maintenance actions; Remark:
Procedure Step
Published
06/17/2021 9:49 AM
321 - Document maintenance actions
Instruction
Published
04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866
Procedure Step
Published
06/18/2021 5:58 PM
2585 - Document maintenance performed
Instruction
Published
07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.
Remark
Published
04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864
Procedure Step
Published
06/29/2022 9:50 AM
4705 - Submit report
Instruction
Published
06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.
Remark
Published
07/28/2022 1:36 PM
Corrective Maintenance Procedure
Document Type
Published
03/02/2020 3:32 PM
minutes
Duration
Published
05/26/2022 11:41 AM
As Needed
Frequency
Published
04/01/2020 11:36 AM
Note
Annotation Type
Published
03/02/2020 3:25 PM
Caution
Annotation Type
Published
03/02/2020 3:24 PM
Technician 1
Skill Level
Published
05/14/2020 2:56 PM
Small slotted (flathead) screwdriver
Tools
Published
09/11/2020 11:23 AM
Wire cutter pliers
Tools
Published
10/27/2022 1:20 PM
T10 Torx screwdriver
Tools
Published
11/10/2022 12:57 PM
Medium pliers
Tools
Published
11/03/2022 2:20 PM
Needle nose pliers
Tools
Published
05/06/2020 4:10 PM
Fluke 179 Digital Multimeter (DMM)
Tools
Published
03/20/2021 6:27 PM
Power off Packeye
படம்
Published
02/19/2022 1:48 AM
packeye_di_opentop_redarrow_00758.jpg
படம்
Published
10/20/2023 12:55 PM
packeye_di_distrobox_remove.jpg
படம்
Published
10/20/2023 4:00 PM
packeye_di_batterycable_remove.jpg
படம்
Published
10/20/2023 3:54 PM
packeye_di_batterycable_2prong.jpg
படம்
Published
10/20/2023 3:51 PM
packeye_di_rs232cable_remove.jpg
படம்
Published
10/23/2023 9:49 AM
packeye_di_rs232btadisconnect.jpg
படம்
Published
10/23/2023 1:46 PM
packeye_di_powercable_ties_locate.jpg
படம்
Published
10/20/2023 4:02 PM
packeye_di_powermodule_remove.jpg
படம்
Published
10/20/2023 4:04 PM
packeye_di_powersupp_screws.jpg
படம்
Published
10/23/2023 1:47 PM
packeye_di_powersupp_slideopen.jpg
படம்
Published
10/23/2023 1:48 PM
packeye_di_powersupp_internalview.jpg
படம்
Published
10/23/2023 1:50 PM
packeye_di_powersupp_pcb.jpg
படம்
Published
10/23/2023 1:51 PM
packeye_di_powersupp_spadeoff.jpg
படம்
Published
10/23/2023 1:53 PM
packeye_di_powersupp_spadeon.jpg
படம்
Published
10/23/2023 1:54 PM
packeye_di_powersupp_alignslot3.jpg
படம்
Published
10/23/2023 1:55 PM
packeye_di_powersupp_slideclosed.jpg
படம்
Published
10/23/2023 1:49 PM
packeye_di_powermodule_install.jpg
படம்
Published
10/20/2023 4:03 PM
packeye_di_batterycable_install.jpg
படம்
Published
10/20/2023 3:53 PM
packeye_di_distrobox_install.jpg
படம்
Published
10/20/2023 3:59 PM
packeye_di_rs232btaconnectinsert.jpg
படம்
Published
10/23/2023 1:44 PM
packeye_di_rs232cable_insert.jpg
படம்
Published
10/23/2023 9:48 AM

PackEye Refurbish Power Supply

Last Updated: 04/24/2025 1:42 AM

The following table lists all the components that make up the document.

Title Type Status Last Updated
Thermo FHT1377 PackEye
Device
Published
10/28/2024 3:37 PM
5662 - 5661 - Uninstall Power Supply Module; Remark:
Procedure Step
Published
11/02/2022 5:10 PM
5661 - Uninstall Power Supply Module
Instruction
Published
11/02/2022 5:09 PM
5660 - 313 - Power off instrument; Remark:4086
Procedure Step
Published
04/07/2025 4:34 PM
313 - Power off instrument
Instruction
Published
07/23/2021 2:41 PM
4086 - Press and hold the power button for approximately 10 seconds until indicator ...
Remark
Published
05/02/2022 6:04 PM
5666 - 4222 - Place instrument on flat surface; Remark:4221
Procedure Step
Published
11/03/2022 8:17 AM
4222 - Place instrument on flat surface
Instruction
Published
05/10/2022 1:54 PM
4221 - Shoulder straps should be facing down.
Remark
Published
05/10/2022 1:55 PM
5667 - 3876 - Open top of backpack; Remark:5665
Procedure Step
Published
11/03/2022 8:21 AM
3876 - Open top of backpack
Instruction
Published
04/04/2022 3:14 PM
5665 - IO PackEye Open Top for Battery
Remark
Published
11/09/2024 8:06 PM
5668 - 4219 - Remove distribution box; Remark:4218
Procedure Step
Published
11/03/2022 8:22 AM
4219 - Remove distribution box
Instruction
Published
05/10/2022 1:58 PM
4218 - The distribution box is usually located in the top of the backpack.
Remark
Published
05/10/2022 1:58 PM
5669 - 4217 - Disconnect battery cable; Remark:4216
Procedure Step
Published
11/03/2022 8:47 AM
5664 - Note : The other cord connected to the distribution box is the headphone plug.
Annotation
Published
11/03/2022 8:47 AM
4217 - Disconnect battery cable
Instruction
Published
05/10/2022 2:01 PM
4216 - Rotate the collar counterclockwise and pull straight out. The battery cable c...
Remark
Published
05/10/2022 2:03 PM
5673 - 5672 - Disconnect RS232 jumper; Remark:5670
Procedure Step
Published
11/03/2022 9:07 AM
5672 - Disconnect RS232 jumper
Instruction
Published
11/03/2022 9:03 AM
5670 - Use small, slotted screwdriver.
Remark
Published
11/03/2022 9:07 AM
5671 - IO PackEye RS232 Disconnect Cable
Remark
Published
11/09/2024 8:07 PM
5680 - 5679 - Disconnect Bluetooth adapter cable; Remark:5670
Procedure Step
Published
11/03/2022 9:15 AM
5679 - Disconnect Bluetooth adapter cable
Instruction
Published
11/03/2022 9:12 AM
5678 - IO PackEye Cable for BTA Disconnect
Remark
Published
11/09/2024 8:08 PM
5681 - 5677 - Remove wire ties; Remark:5676
Procedure Step
Published
11/03/2022 9:27 AM
5677 - Remove wire ties
Instruction
Published
11/03/2022 9:16 AM
5676 - Note location of wire ties for reassembly. Use wire cutter or scissors.
Remark
Published
11/03/2022 9:27 AM
5770 - IO PackEye Power Cable Ties Location
Remark
Published
11/09/2024 8:08 PM
5682 - 5675 - Remove power supply module; Remark:5674
Procedure Step
Published
11/03/2022 9:35 AM
5675 - Remove power supply module
Instruction
Published
11/03/2022 9:31 AM
5674 - There are Velcro strips securing the power supply module to the FHT 681 ampli...
Remark
Published
11/03/2022 9:35 AM
5713 - 5712 - Remove Faulty Internal Battery; Remark:
Procedure Step
Published
11/03/2022 9:43 AM
5712 - Remove Faulty Internal Battery
Instruction
Published
11/03/2022 9:43 AM
5706 - 5705 - Remove two (2) enclosure screws; Remark:5703
Procedure Step
Published
11/03/2022 10:49 AM
5705 - Remove two (2) enclosure screws
Instruction
Published
11/03/2022 10:03 AM
5703 - Use T-10 Torx screwdriver. Remove the screws only on the side where the power...
Remark
Published
11/03/2022 10:05 AM
5704 - IO PackEye Power Module Screws
Remark
Published
11/09/2024 8:09 PM
5707 - 5702 - Remove electronics; Remark:5701
Procedure Step
Published
11/03/2022 10:53 AM
5702 - Remove electronics
Instruction
Published
11/03/2022 10:50 AM
5701 - IO PackEye Power Module Slide Open
Remark
Published
11/09/2024 8:12 PM
5708 - 1813 - Disconnect battery; Remark:5808
Procedure Step
Published
11/03/2022 11:02 AM
1813 - Disconnect battery
Instruction
Published
11/20/2020 9:31 AM
5808 - IO PackEye Power Battery Disconnect
Remark
Published
11/09/2024 8:12 PM
5709 - 5700 - Cut wire ties; Remark:5699
Procedure Step
Published
11/03/2022 12:28 PM
5700 - Cut wire ties
Instruction
Published
11/03/2022 12:26 PM
5699 - Use wire cutters.
Remark
Published
11/03/2022 12:28 PM
5710 - 5270 - Remove battery; Remark:
Procedure Step
Published
11/03/2022 12:30 PM
5270 - Remove battery
Instruction
Published
10/17/2022 2:02 PM
5711 - 5698 - Remove foam pad from faulty battery; Remark:5697
Procedure Step
Published
11/03/2022 12:33 PM
5698 - Remove foam pad from faulty battery
Instruction
Published
11/03/2022 12:31 PM
5697 - Set aside to reuse on new battery.
Remark
Published
11/03/2022 12:33 PM
5744 - 5743 - Install New Internal Battery; Remark:
Procedure Step
Published
11/03/2022 12:49 PM
5743 - Install New Internal Battery
Instruction
Published
11/03/2022 12:48 PM
5734 - 5733 - Set new battery in place; Remark:5732
Procedure Step
Published
11/03/2022 12:51 PM
5733 - Set new battery in place
Instruction
Published
11/03/2022 12:49 PM
5732 - Align the new battery on the circuit board. Verify wiring connectors are in t...
Remark
Published
11/03/2022 12:51 PM
5735 - 5731 - Secure battery to circuit board; Remark:5730
Procedure Step
Published
11/03/2022 12:55 PM
5731 - Secure battery to circuit board
Instruction
Published
11/03/2022 12:52 PM
5730 - Use two (2) wire ties. Cut excess wire tie.
Remark
Published
11/03/2022 12:54 PM
5736 - 5729 - Attach padded foam to new battery; Remark:5728
Procedure Step
Published
11/03/2022 12:57 PM
5729 - Attach padded foam to new battery
Instruction
Published
11/03/2022 12:55 PM
5728 - If the old pad is not reusable, it is recommended to use a new piece.
Remark
Published
11/03/2022 12:57 PM
5737 - 5726 - Remove existing connector (if needed); Remark:5725
Procedure Step
Published
11/03/2022 1:02 PM
5727 - Caution : Only cut one wire at a time.
Annotation
Published
11/03/2022 1:02 PM
5726 - Remove existing connector (if needed)
Instruction
Published
11/03/2022 12:58 PM
5725 - The existing connector might need to be removed. Make sure enough wire is ava...
Remark
Published
11/03/2022 1:01 PM
5738 - 1821 - Connect battery; Remark:5724
Procedure Step
Published
11/03/2022 1:05 PM
1821 - Connect battery
Instruction
Published
11/20/2020 9:26 AM
5724 - Use wire crimpers to attach insulated female spade quick connectors.
Remark
Published
11/03/2022 1:05 PM
5739 - 5723 - Check connections; Remark:5722
Procedure Step
Published
11/03/2022 1:11 PM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.
Annotation
Published
10/28/2022 2:19 PM
5723 - Check connections
Instruction
Published
11/03/2022 1:07 PM
5722 - The ground wire (usually black) must be connected to the terminal closest to ...
Remark
Published
11/03/2022 1:10 PM
5740 - 5720 - Replace electronics; Remark:5719
Procedure Step
Published
11/03/2022 1:15 PM
5721 - Caution : Circuit board must be inserted correctly to prevent damage to components....
Annotation
Published
11/03/2022 1:15 PM
5720 - Replace electronics
Instruction
Published
11/03/2022 1:11 PM
5719 - Align circuit board with third slot from bottom of enclosure and slide into p...
Remark
Published
11/03/2022 1:15 PM
5741 - 5718 - Align gasket; Remark:5717
Procedure Step
Published
11/03/2022 1:18 PM
5718 - Align gasket
Instruction
Published
11/03/2022 1:16 PM
5717 - Verify gasket is aligned between housing and end panel before inserting screw...
Remark
Published
11/03/2022 1:18 PM
5742 - 5716 - Reinstall two (2) enclosure screws; Remark:5714
Procedure Step
Published
11/03/2022 1:22 PM
5716 - Reinstall two (2) enclosure screws
Instruction
Published
11/03/2022 1:19 PM
5714 - Use T-10 Torx screwdriver.
Remark
Published
11/03/2022 1:20 PM
5780 - 5779 - Reinstall Power Supply Module; Remark:
Procedure Step
Published
11/03/2022 1:25 PM
5779 - Reinstall Power Supply Module
Instruction
Published
11/03/2022 1:25 PM
5776 - 5775 - Secure power supply module to FHT 681; Remark:5774
Procedure Step
Published
11/03/2022 2:50 PM
5775 - Secure power supply module to FHT 681
Instruction
Published
11/03/2022 2:46 PM
5774 - The module will snap into place.
Remark
Published
11/03/2022 2:50 PM
5777 - 5773 - Reconnect battery cable; Remark:5772
Procedure Step
Published
11/03/2022 2:55 PM
5773 - Reconnect battery cable
Instruction
Published
11/03/2022 2:51 PM
5772 - Align the connector and push in. Rotate collar clockwise and hand-tighten.
Remark
Published
11/03/2022 2:55 PM
5778 - 5771 - Install wire ties; Remark:5769
Procedure Step
Published
11/03/2022 3:06 PM
5771 - Install wire ties
Instruction
Published
11/03/2022 2:56 PM
5769 - If desired, install new wire ties and cut off excess.
Remark
Published
11/03/2022 3:05 PM
5790 - 4237 - Replace distribution box; Remark:4236
Procedure Step
Published
11/03/2022 3:16 PM
4237 - Replace distribution box
Instruction
Published
05/10/2022 2:15 PM
4236 - IO PackEye Distro Box Install
Remark
Published
10/24/2024 6:53 PM
5791 - 5788 - Reconnect Bluetooth adapter cable; Remark:5787
Procedure Step
Published
11/03/2022 3:18 PM
5788 - Reconnect Bluetooth adapter cable
Instruction
Published
11/03/2022 3:17 PM
5787 - IO PackEye Cable for BTA Connect
Remark
Published
11/09/2024 8:13 PM
5792 - 5786 - Reconnect RS232 jumper; Remark:5785
Procedure Step
Published
11/03/2022 3:42 PM
5786 - Reconnect RS232 jumper
Instruction
Published
11/03/2022 3:39 PM
5785 - Use small, slotted screwdriver to secure connector.
Remark
Published
11/16/2022 9:35 AM
5830 - IO PackEye RS232 Connect Cable
Remark
Published
11/09/2024 8:14 PM
5763 - 5762 - Check Battery Charging; Remark:
Procedure Step
Published
11/03/2022 2:48 PM
5762 - Check Battery Charging
Instruction
Published
11/03/2022 2:48 PM
5798 - 4718 - Connect charger; Remark:5797
Procedure Step
Published
11/03/2022 3:57 PM
4718 - Connect charger
Instruction
Published
06/29/2022 1:15 PM
5797 - IO PackEye Battery Charger Connection
Remark
Published
11/09/2024 8:15 PM
5807 - IO PackEye Battery Connect Cable
Remark
Published
11/09/2024 8:15 PM
5799 - 4716 - Verify instrument is charging; Remark:5752
Procedure Step
Published
11/03/2022 4:01 PM
4716 - Verify instrument is charging
Instruction
Published
06/29/2022 1:16 PM
5752 - CHARGE (yellow) and READY (green) LEDs will...
Remark
Published
11/10/2022 9:17 AM
5800 - 5796 - Charge Instrument; Remark:5795
Procedure Step
Published
11/03/2022 4:04 PM
5796 - Charge Instrument
Instruction
Published
11/03/2022 4:02 PM
5795 - It is recommended to fully charge the battery before first use. Only the gree...
Remark
Published
11/03/2022 4:04 PM
322 - 321 - Document maintenance actions; Remark:
Procedure Step
Published
06/17/2021 9:49 AM
321 - Document maintenance actions
Instruction
Published
04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866
Procedure Step
Published
06/18/2021 5:58 PM
2585 - Document maintenance performed
Instruction
Published
07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.
Remark
Published
04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864
Procedure Step
Published
06/29/2022 9:50 AM
4705 - Submit report
Instruction
Published
06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.
Remark
Published
07/28/2022 1:36 PM
Corrective Maintenance Procedure
Document Type
Published
03/02/2020 3:32 PM
minutes
Duration
Published
05/26/2022 11:41 AM
As Needed
Frequency
Published
04/01/2020 11:36 AM
Note
Annotation Type
Published
03/02/2020 3:25 PM
Caution
Annotation Type
Published
03/02/2020 3:24 PM
Technician 3
Skill Level
Published
05/14/2020 2:56 PM
Small slotted (flathead) screwdriver
Tools
Published
09/11/2020 11:23 AM
Wire cutter pliers
Tools
Published
10/27/2022 1:20 PM
T10 Torx screwdriver
Tools
Published
11/10/2022 12:57 PM
Medium pliers
Tools
Published
11/03/2022 2:20 PM
Wire Crimpers
Tools
Published
11/03/2022 4:56 PM
Power off Packeye
படம்
Published
02/19/2022 1:48 AM
packeye_di_opentop_redarrow_00758.jpg
படம்
Published
10/20/2023 12:55 PM
packeye_di_distrobox_remove.jpg
படம்
Published
10/20/2023 4:00 PM
packeye_di_batterycable_remove.jpg
படம்
Published
10/20/2023 3:54 PM
packeye_di_batterycable_2prong.jpg
படம்
Published
10/20/2023 3:51 PM
packeye_di_rs232cable_remove.jpg
படம்
Published
10/23/2023 9:49 AM
packeye_di_rs232btadisconnect.jpg
படம்
Published
10/23/2023 1:46 PM
packeye_di_powercable_ties_locate.jpg
படம்
Published
10/20/2023 4:02 PM
packeye_di_powermodule_remove.jpg
படம்
Published
10/20/2023 4:04 PM
packeye_di_powersupp_screws.jpg
படம்
Published
10/23/2023 1:47 PM
packeye_di_powersupp_slideopen.jpg
படம்
Published
10/23/2023 1:48 PM
packeye_di_power_battery_disconnect.jpg
படம்
Published
10/24/2023 3:21 PM
packeye_di_battery_cutties.jpg
படம்
Published
10/23/2023 2:19 PM
packeye_di_battery_removefoam.jpg
படம்
Published
10/23/2023 2:22 PM
packeye_di_battery_installties.jpg
படம்
Published
10/23/2023 2:25 PM
packeye_di_battery_installfoam.jpg
படம்
Published
10/23/2023 2:23 PM
packeye_di_battery_cutwires.jpg
படம்
Published
10/23/2023 2:21 PM
packeye_di_battery_installspade.jpg
படம்
Published
10/23/2023 2:24 PM
packeye_di_powersupp_spadeon.jpg
படம்
Published
10/23/2023 1:54 PM
packeye_di_powersupp_alignslot3.jpg
படம்
Published
10/23/2023 1:55 PM
packeye_di_powersupp_slideclosed.jpg
படம்
Published
10/23/2023 1:49 PM
packeye_di_powermodule_install.jpg
படம்
Published
10/20/2023 4:03 PM
packeye_di_batterycable_install.jpg
படம்
Published
10/20/2023 3:53 PM
packeye_di_distrobox_install.jpg
படம்
Published
10/20/2023 3:59 PM
packeye_di_rs232btaconnectinsert.jpg
படம்
Published
10/23/2023 1:44 PM
packeye_di_rs232cable_insert.jpg
படம்
Published
10/23/2023 9:48 AM
packeye_di_battery_chargerconnector.jpg
படம்
Published
10/23/2023 2:17 PM
packeye_di_charger_connect_redarrow_00783.jpg
படம்
Published
10/20/2023 12:53 PM
packeye_di_batteryCHARGING_0.jpg
படம்
Published
10/23/2023 1:43 PM
packeye_di_batteryREADY.jpg
படம்
Published
10/23/2023 9:34 AM