Utility knife | FRONTLINE Maintenance Tool

RPM IXIO-DT1 Occupancy Sensor Replacement

Last Updated: 04/26/2025 1:42 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
7478 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/01/2023 7:48 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7452 - 7231 - Close lane; Remark:7415	Procedure Step	Published	06/02/2023 5:12 PM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7415 - Re-route pedestrian traffic.	Remark	Published	06/02/2023 1:08 PM
7453 - 7232 - Open RPM door; Remark:7267	Procedure Step	Published	06/02/2023 5:24 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7267 - Open all doors needed to access components.	Remark	Published	09/16/2023 4:54 PM
7454 - 7290 - Disable tamper switches; Remark:7416	Procedure Step	Published	06/02/2023 5:25 PM
7290 - Disable tamper switches	Instruction	Published	05/01/2023 8:14 AM
7416 - Use a magnet to disable tamper switches for all open doors. Use adhesive tape...	Remark	Published	06/02/2023 1:18 PM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
7479 - 7417 - Prepare New Occupancy Sensor; Remark:	Procedure Step	Published	06/02/2023 6:13 PM
7417 - Prepare New Occupancy Sensor	Instruction	Published	06/02/2023 1:39 PM
7456 - 7418 - Remove cover from new occupancy sensor; Remark:7419	Procedure Step	Published	06/02/2023 5:27 PM
7418 - Remove cover from new occupancy sensor	Instruction	Published	06/02/2023 1:43 PM
7419 - Use a slotted screwdriver to pry the cover off from the side.	Remark	Published	04/13/2025 5:44 PM
7457 - 7420 - Verify narrow field radar antenna is installed; Remark:7421	Procedure Step	Published	04/13/2025 6:18 PM
7420 - Verify narrow field radar antenna is installed	Instruction	Published	04/13/2025 5:44 PM
7421 - The IXIO-DT1 should come with the narrow field antenna installed.	Remark	Published	06/02/2023 2:14 PM
8901 - If needed, the antenna can be changed. Remove cover. Install narrow field ant...	Remark	Published	09/25/2023 9:51 PM
7480 - 7422 - Uninstall Faulty Occupancy Sensor; Remark:	Procedure Step	Published	06/02/2023 9:42 PM
7422 - Uninstall Faulty Occupancy Sensor	Instruction	Published	06/02/2023 2:16 PM
7458 - 7423 - Remove Cover; Remark:7424	Procedure Step	Published	06/02/2023 5:28 PM
7423 - Remove Cover	Instruction	Published	06/02/2023 2:18 PM
7424 - If needed, use a sharp utility knife to cut sealant around edges of sensor. A...	Remark	Published	06/02/2023 2:21 PM
7459 - 7425 - Disconnect wire connector; Remark:7426	Procedure Step	Published	06/02/2023 5:29 PM
7425 - Disconnect wire connector	Instruction	Published	06/02/2023 2:48 PM
7426 - The wire connector is located on the right side of existing sensor.	Remark	Published	06/02/2023 2:53 PM
7460 - 7427 - Loosen two (2) mounting screws; Remark:7428	Procedure Step	Published	06/02/2023 5:30 PM
7429 - Note : Some existing occupancy sensors are installed using screws and nuts, ...	Annotation	Published	06/02/2023 3:09 PM
7427 - Loosen two (2) mounting screws	Instruction	Published	06/02/2023 2:56 PM
7428 - Use a medium Phillips (PH2) screwdriver. If screws and nuts were used, an adj...	Remark	Published	06/02/2023 3:04 PM
7461 - 7430 - Remove faulty occupancy sensor; Remark:7431	Procedure Step	Published	06/02/2023 5:31 PM
7430 - Remove faulty occupancy sensor	Instruction	Published	06/02/2023 3:11 PM
7431 - If a Wizard G3 sensor is being removed, push up on both sides to free the sen...	Remark	Published	09/29/2023 1:49 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
7481 - 7432 - Install new occupancy sensor; Remark:	Procedure Step	Published	06/02/2023 9:46 PM
7432 - Install new occupancy sensor	Instruction	Published	06/02/2023 3:27 PM
7463 - 7433 - Mount new sensor; Remark:7434	Procedure Step	Published	06/02/2023 5:32 PM
7433 - Mount new sensor	Instruction	Published	06/02/2023 3:29 PM
7434 - First, slide left side onto mounting screw.	Remark	Published	04/13/2025 5:44 PM
9206 - Then, place right side over mounting screw and push down.	Remark	Published	09/29/2023 1:55 PM
7464 - 7435 - Tighten two (2) mounting screws; Remark:7436	Procedure Step	Published	06/02/2023 5:33 PM
7435 - Tighten two (2) mounting screws	Instruction	Published	06/02/2023 3:40 PM
7436 - Use medium Phillips (PH2) screwdriver. Take care not to overtighten.	Remark	Published	04/13/2025 5:45 PM
7482 - 7437 - Route wiring through clamp and connect; Remark:7488	Procedure Step	Published	06/02/2023 10:42 PM
7437 - Route wiring through clamp and connect	Instruction	Published	06/02/2023 3:53 PM
7488 - Clamp and Connect	Remark	Published	06/02/2023 10:49 PM
7465 - 7439 - Adjust angle of the radar antenna; Remark:7438	Procedure Step	Published	04/13/2025 6:19 PM
7439 - Adjust angle of the radar antenna	Instruction	Published	04/13/2025 5:45 PM
7438 - The angle is adjusted by manually rotating the antenna up or down. The defaul...	Remark	Published	09/29/2023 1:58 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7466 - 7440 - Hold door open; Remark:7441	Procedure Step	Published	06/02/2023 5:35 PM
7440 - Hold door open	Instruction	Published	06/02/2023 4:10 PM
7441 - Do not move door. Door must remain stationary to prevent occupancy.	Remark	Published	04/13/2025 5:45 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7468 - 7304 - Confirm RPM has restarted correctly; Remark:7487	Procedure Step	Published	06/02/2023 5:36 PM
7304 - Confirm RPM has restarted correctly	Instruction	Published	05/01/2023 8:31 AM
7487 - The SC-770 controller will display "OK" following Power On Self-Test (POST) a...	Remark	Published	06/02/2023 10:35 PM
7282 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	04/27/2023 4:15 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
7470 - 7442 - Generate occupancy; Remark:7443	Procedure Step	Published	06/02/2023 5:37 PM
7442 - Generate occupancy	Instruction	Published	06/02/2023 4:19 PM
7443 - Create motion in front of occupancy sensor. While holding the door open and s...	Remark	Published	06/02/2023 4:21 PM
7471 - 7444 - Verify occupancy sensor functionality; Remark:7445	Procedure Step	Published	06/02/2023 5:38 PM
7444 - Verify occupancy sensor functionality	Instruction	Published	06/02/2023 4:32 PM
7445 - IXIO-DT1 green sensor light will illuminate.	Remark	Published	06/02/2023 4:35 PM
8973 - Left latch on the LCD screen will indicate a “closed” circuit.	Remark	Published	09/25/2023 11:05 PM
8974 - SC-770 status will read “OCCUPIED”.	Remark	Published	09/25/2023 11:06 PM
7472 - 7446 - Install sensor cover; Remark:7447	Procedure Step	Published	06/02/2023 5:38 PM
7446 - Install sensor cover	Instruction	Published	06/02/2023 4:37 PM
7447 - The cover should snap into place.	Remark	Published	06/02/2023 4:38 PM
7473 - 7448 - If needed, apply sealant; Remark:7449	Procedure Step	Published	06/02/2023 5:39 PM
7448 - If needed, apply sealant	Instruction	Published	06/02/2023 4:39 PM
7449 - If used outdoors, sealant should be applied to top and sides of cover. Do not...	Remark	Published	06/02/2023 4:41 PM
7474 - 7310 - Enable tamper switches; Remark:7451	Procedure Step	Published	06/02/2023 5:41 PM
7310 - Enable tamper switches	Instruction	Published	05/01/2023 8:36 AM
7451 - Remove magnets and/or adhesive tape from door tamper switches.	Remark	Published	04/13/2025 5:46 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
Instrument is not functioning correctly	Frequency	Published	12/19/2022 5:52 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Magnets and adhesive tape to disable door tamper switches	Replacement Parts	Published	06/02/2023 10:08 PM
Medium slotted screwdriver	Replacement Parts	Published	06/02/2023 10:08 PM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Adjustable wrench	Replacement Parts	Published	06/02/2023 10:08 PM
Utility knife	Tools	Published	05/19/2020 1:54 PM
Orange/yellow safety vest	Replacement Parts	Published	04/27/2023 6:56 PM
Safety shoes	Replacement Parts	Published	04/27/2023 6:56 PM
Gloves	Replacement Parts	Published	05/10/2023 3:28 PM
Protective headwear: glasses, hard hat	Replacement Parts	Published	05/10/2023 3:31 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
Disable tamper switch	Image	Published	09/07/2023 8:22 PM
Disable Tamper Switch	Image	Published	06/02/2023 2:28 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Remove Occupancy Sensor Cover	Image	Published	06/02/2023 2:38 PM
The IXIO-DT1 should come with the narrow field antenna installed	Image	Published	09/25/2023 8:35 PM
Verify narrow field radar antenna is installed	Image	Published	09/25/2023 8:38 PM
Verify narrow field radar antenna is installed 2	Image	Published	09/25/2023 8:39 PM
Uninstall Occupancy Sensor Cover	Image	Published	06/02/2023 2:37 PM
Disconnect Wire Connector	Image	Published	06/02/2023 2:53 PM
Loosen Two Mounting screws	Image	Published	06/02/2023 3:04 PM
Remove faulty Occupancy Sensor	Image	Published	09/29/2023 1:47 PM
Push Occupancy Sensor to the right	Image	Published	09/29/2023 1:48 PM
Mount new sensor	Image	Published	09/25/2023 8:52 PM
Push Down Over Mounting Screw to Install Occupancy Sensor	Image	Published	06/02/2023 3:51 PM
Tighten Occupancy Sensor Mounting Screws	Image	Published	06/02/2023 3:48 PM
Route wiring through clamp and connect	Image	Published	06/02/2023 3:55 PM
Adjust angle of the radar antenna	Image	Published	09/25/2023 8:56 PM
Adjust angle of the radar antenna2	Image	Published	09/25/2023 8:58 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
IXIO-DT1 green sensor light will illuminate	Image	Published	09/25/2023 9:37 PM
Verify occupancy sensor functionality	Image	Published	09/25/2023 9:38 PM
Verify occupancy sensor functionality2	Image	Published	09/25/2023 9:39 PM
Install Occupancy Sensor Cover	Image	Published	06/02/2023 4:26 PM
Occupancy Sensor Sealant Application	Image	Published	06/02/2023 4:30 PM
Remove Magnet from Tamper.PNG	Image	Published	09/28/2023 9:37 AM
Remove Magnet on Tamper Switch	Image	Published	06/02/2023 4:31 PM

Read more about RPM IXIO-DT1 Occupancy Sensor Replacement

PackEye Gamma Detector Replacement

Last Updated: 04/26/2025 1:42 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Thermo FHT1377 PackEye	Device	Published	10/28/2024 3:37 PM
6676 - 6675 - Unpack Instrument; Remark:	Procedure Step	Published	12/09/2022 10:45 AM
6675 - Unpack Instrument	Instruction	Published	12/09/2022 10:45 AM
3869 - 313 - Power off instrument; Remark:3850	Procedure Step	Published	03/29/2022 2:23 AM
313 - Power off instrument	Instruction	Published	07/23/2021 2:41 PM
3850 - Press and hold the power button for approximately 10 seconds until indicator ...	Remark	Published	03/29/2022 1:38 AM
4223 - 4222 - Place instrument on flat surface; Remark:4221	Procedure Step	Published	05/10/2022 1:56 PM
4222 - Place instrument on flat surface	Instruction	Published	05/10/2022 1:54 PM
4221 - Shoulder straps should be facing down.	Remark	Published	05/10/2022 1:55 PM
3926 - 3876 - Open top of backpack; Remark:3928	Procedure Step	Published	04/05/2022 5:28 PM
3876 - Open top of backpack	Instruction	Published	04/04/2022 3:14 PM
3928 - IO PackEye Open Top of Backpack for Battery Access	Remark	Published	10/24/2024 6:52 PM
6217 - 6216 - Disconnect straps on sides of backpack; Remark:6215	Procedure Step	Published	11/28/2022 9:50 AM
6216 - Disconnect straps on sides of backpack	Instruction	Published	11/28/2022 9:46 AM
6215 -	Remark	Published	11/28/2022 9:50 AM
6709 - 6708 - Remove backpack contents; Remark:6707	Procedure Step	Published	12/09/2022 1:27 PM
6708 - Remove backpack contents	Instruction	Published	12/09/2022 1:26 PM
6707 - Slowly slide foam assembly out of backpack. This process might take two peopl...	Remark	Published	12/09/2022 1:27 PM
6710 - 6706 - Open protective foam; Remark:6705	Procedure Step	Published	12/09/2022 1:30 PM
6706 - Open protective foam	Instruction	Published	12/09/2022 1:27 PM
6705 - Use utility knife or scissors. Cut tape on one side of foam assembly.	Remark	Published	12/09/2022 1:28 PM
6674 - 6673 - Remove Faulty Gamma Detector; Remark:	Procedure Step	Published	12/09/2022 10:36 AM
6673 - Remove Faulty Gamma Detector	Instruction	Published	12/09/2022 10:36 AM
6225 - 6221 - Disconnect gamma detector; Remark:6220	Procedure Step	Published	11/28/2022 10:03 AM
6221 - Disconnect gamma detector	Instruction	Published	11/28/2022 9:59 AM
6220 - The gamma detector is connected to the FHT 681 amplifier at PMT1	Remark	Published	11/28/2022 10:03 AM
6724 - 1673 - Remove gamma detector; Remark:6723	Procedure Step	Published	12/09/2022 1:36 PM
1673 - Remove gamma detector	Instruction	Published	12/09/2022 1:34 PM
6723 - IO PackEye gamma detector over foam	Remark	Published	12/09/2022 1:36 PM
6725 - 6722 - Disconnect cable from gamma detector; Remark:6721	Procedure Step	Published	12/09/2022 1:41 PM
6722 - Disconnect cable from gamma detector	Instruction	Published	12/09/2022 1:37 PM
6721 - Keep the right-angle connector on the cable. Push toward connection, turn cou...	Remark	Published	12/09/2022 1:38 PM
6672 - 6671 - Install New Gamma Detector; Remark:	Procedure Step	Published	12/09/2022 10:36 AM
6671 - Install New Gamma Detector	Instruction	Published	12/09/2022 10:36 AM
6719 - 6328 - Reseat gamma connectors; Remark:6718	Procedure Step	Published	12/09/2022 1:40 PM
6328 - Reseat gamma connectors	Instruction	Published	11/29/2022 9:15 AM
6718 - Disconnect and reconnect both connections to the 90-degree elbow several time...	Remark	Published	12/09/2022 1:39 PM
6720 - 6717 - Set gamma detector in place; Remark:6716	Procedure Step	Published	12/09/2022 1:41 PM
6717 - Set gamma detector in place	Instruction	Published	12/09/2022 1:40 PM
6716 - Insert the gamma detector into the foam. Route the cable through the foam to ...	Remark	Published	12/09/2022 1:40 PM
6332 - 6328 - Reseat gamma connectors; Remark:6326	Procedure Step	Published	11/29/2022 9:18 AM
6326 - The gamma detector is connected at the FHT 681 amplifier at the connection la...	Remark	Published	11/30/2022 12:21 PM
6327 -	Remark	Published	11/29/2022 9:18 AM
303 - 302 - Reassemble instrument; Remark:	Procedure Step	Published	10/07/2022 1:49 PM
302 - Reassemble instrument	Instruction	Published	06/16/2021 11:28 PM
6737 - 6736 - Secure protective foam together; Remark:6735	Procedure Step	Published	12/09/2022 1:45 PM
6736 - Secure protective foam together	Instruction	Published	12/09/2022 1:44 PM
6735 - Re-wrap the foam assembly with electrical tape. Do not compress the foam....	Remark	Published	12/09/2022 1:45 PM
6333 - 6325 - Repack backpack; Remark:6323	Procedure Step	Published	11/29/2022 9:20 AM
6325 - Repack backpack	Instruction	Published	11/29/2022 9:18 AM
6323 - Slide the protective foam assembly into backpack	Remark	Published	11/29/2022 9:19 AM
6324 -	Remark	Published	11/29/2022 9:20 AM
6344 - 1383 - Close backpack; Remark:6343	Procedure Step	Published	11/29/2022 10:11 AM
1383 - Close backpack	Instruction	Published	11/19/2020 5:23 PM
6343 -	Remark	Published	11/29/2022 10:11 AM
6342 - 6341 - Perform Gamma High Voltage Adjustment; Remark:6340	Procedure Step	Published	11/29/2022 10:13 AM
6341 - Perform Gamma High Voltage Adjustment	Instruction	Published	11/29/2022 10:12 AM
6340 - DET-HHD-THR-PAK-RM05, PackEye Gamma High Voltage Adjustment.	Remark	Published	11/29/2022 10:13 AM
6435 - 2584 - Perform efficiency test; Remark:6434	Procedure Step	Published	11/30/2022 1:39 PM
2584 - Perform efficiency test	Instruction	Published	08/11/2021 3:55 PM
6434 - DET-HHD-THR-RM08, PackEye Efficiency Test.	Remark	Published	11/30/2022 1:38 PM
5761 - 319 - Perform operational test; Remark:5760	Procedure Step	Published	11/03/2022 2:58 PM
319 - Perform operational test	Instruction	Published	06/10/2021 8:31 PM
5760 - DET-HHD-THR-PAK-RM01, PackEye Operational Test	Remark	Published	11/03/2022 2:55 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
minutes	Duration	Published	05/26/2022 11:41 AM
As Needed	Frequency	Published	04/01/2020 11:36 AM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Utility knife	Tools	Published	05/19/2020 1:54 PM
Power off Packeye	Image	Published	02/19/2022 1:48 AM
packeye_di_opentop_redarrow_00758.jpg	Image	Published	10/20/2023 12:55 PM
packeye_di_sidebuckle_open_outside.jpg	Image	Published	10/24/2023 10:18 AM
packeye_di_content_remove_4arrow.jpg	Image	Published	10/24/2023 10:20 AM
packeye_di_foamtape_remove.jpg	Image	Published	10/24/2023 11:18 AM
packeye_di_681removepmt1connector.jpg	Image	Published	10/24/2023 10:24 AM
packeye_di_gammadet_remove.jpg	Image	Published	10/24/2023 11:12 AM
packeye_di_gammaconnector_ondet_remove.jpg	Image	Published	10/24/2023 11:15 AM
packeye_di_gammaconnector_ondet_install.jpg	Image	Published	10/24/2023 11:17 AM
packeye_di_681installpmt1connector.jpg	Image	Published	10/24/2023 10:25 AM
packeye_di_foamtape_install.jpg	Image	Published	10/24/2023 11:18 AM
packeye_di_content_insert_2arrow.jpg	Image	Published	10/24/2023 10:21 AM
packeye_di_closetop_redarrow.jpg	Image	Published	10/24/2023 10:59 AM

Read more about PackEye Gamma Detector Replacement

PRM-470 Charging Port Replacement

Last Updated: 04/26/2025 1:35 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PRM-470 CG	Device	Published	10/28/2024 3:40 PM
Rapiscan PRM-470 CGN	Device	Published	10/28/2024 3:33 PM
247 - 257 - Prepare instrument; Remark:	Procedure Step	Published	04/11/2025 9:08 PM
257 - Prepare instrument	Instruction	Published	04/11/2025 9:07 PM
607 - 205 - Disconnect charger; Remark:	Procedure Step	Published	07/23/2021 2:42 PM
205 - Disconnect charger	Instruction	Published	07/23/2021 2:42 PM
397 - 313 - Power off instrument; Remark:398	Procedure Step	Published	06/11/2021 9:31 AM
313 - Power off instrument	Instruction	Published	07/23/2021 2:41 PM
398 - Press and hold the POWER button until instrument powers off....	Remark	Published	06/18/2021 6:02 PM
275 - 65 - Loosen four (4) cover screws; Remark:264	Procedure Step	Published	07/26/2021 12:42 PM
65 - Loosen four (4) cover screws	Instruction	Published	07/22/2021 12:38 PM
264 - Use a medium Phillips (PH2) screwdriver. Screws do not need to be completely ...	Remark	Published	07/20/2021 3:59 PM
263 - 262 - Remove instrument cover; Remark:413	Procedure Step	Published	08/11/2021 1:41 PM
2771 - Note : There are high-voltage detector circuit boards inside the instrument; however...	Annotation	Published	10/04/2022 11:06 AM
262 - Remove instrument cover	Instruction	Published	07/20/2021 3:35 PM
413 - PRM-470 Remove Instrument Cover	Remark	Published	11/01/2024 8:32 PM
276 - 266 - Locate battery connection; Remark:265	Procedure Step	Published	08/11/2021 3:07 PM
3033 - Note : PRM-470 CGN models have an additional board and connectors not shown in remar...	Annotation	Published	10/04/2022 11:07 AM
266 - Locate battery connection	Instruction	Published	07/20/2021 3:36 PM
265 - Battery connection is labeled 1.	Remark	Published	08/07/2021 11:16 AM
271 - 270 - Disconnect battery; Remark:414	Procedure Step	Published	08/11/2021 1:42 PM
1345 - Note : It is good practice to ensure all cables and connectors are labeled prior to ...	Annotation	Published	10/04/2022 11:08 AM
270 - Disconnect battery	Instruction	Published	07/20/2021 3:37 PM
414 - PRM-470_Disconnect_battery	Remark	Published	11/02/2024 1:21 PM
443 - 442 - Disconnect remaining connectors; Remark:	Procedure Step	Published	08/11/2021 1:43 PM
442 - Disconnect remaining connectors	Instruction	Published	07/22/2021 12:39 PM
717 - 716 - Unbundle wiring; Remark:715	Procedure Step	Published	08/12/2021 7:49 AM
716 - Unbundle wiring	Instruction	Published	08/11/2021 11:56 AM
715 - Carefully cut wire ties with scissors, knife or clippers. Remove foam (if pre...	Remark	Published	08/11/2021 11:57 AM
719 - 718 - Replace charging port; Remark:	Procedure Step	Published	08/11/2021 3:07 PM
718 - Replace charging port	Instruction	Published	08/11/2021 11:58 AM
728 - 724 - Detach port from case; Remark:720	Procedure Step	Published	08/11/2021 3:08 PM
724 - Detach port from case	Instruction	Published	08/11/2021 11:59 AM
720 - Using pliers or slotted screwdriver, carefully push locking tabs on side of p...	Remark	Published	08/11/2021 12:00 PM
729 - 725 - Remove faulty charging port and cable; Remark:721	Procedure Step	Published	08/11/2021 3:08 PM
725 - Remove faulty charging port and cable	Instruction	Published	08/11/2021 12:01 PM
721 - PRM-470 - the old charging port is pulled out of the charger body	Remark	Published	11/02/2024 5:11 PM
730 - 726 - Insert new charging port; Remark:722	Procedure Step	Published	08/11/2021 3:10 PM
726 - Insert new charging port	Instruction	Published	08/11/2021 12:02 PM
722 - Insert new charging port wiring through opening in case, white connector firs...	Remark	Published	08/11/2021 12:03 PM
731 - 727 - Secure new charging port; Remark:723	Procedure Step	Published	08/11/2021 3:10 PM
727 - Secure new charging port	Instruction	Published	08/11/2021 12:04 PM
723 - Align port with opening and snap into place. Place the key notch toward the b...	Remark	Published	08/11/2021 12:06 PM
303 - 302 - Reassemble instrument; Remark:	Procedure Step	Published	10/07/2022 1:49 PM
302 - Reassemble instrument	Instruction	Published	06/16/2021 11:28 PM
500 - 498 - Reconnect all connectors except battery; Remark:499	Procedure Step	Published	08/11/2021 2:02 PM
498 - Reconnect all connectors except battery	Instruction	Published	07/22/2021 1:02 PM
499 - Do not connect location 1.	Remark	Published	07/22/2021 1:17 PM
306 - 305 - Reconnect battery; Remark:416	Procedure Step	Published	08/11/2021 3:11 PM
305 - Reconnect battery	Instruction	Published	07/29/2021 3:48 PM
416 - PRM-470 Battery Replacement - Reconnect battery	Remark	Published	11/02/2024 2:02 PM
734 - 733 - Secure wiring; Remark:732	Procedure Step	Published	08/12/2021 7:50 AM
733 - Secure wiring	Instruction	Published	08/11/2021 12:07 PM
732 - Bind wiring together with new wire ties. Cut excess wire tie material. Reinse...	Remark	Published	08/11/2021 12:08 PM
308 - 307 - Replace front cover; Remark:	Procedure Step	Published	08/11/2021 2:03 PM
304 - Caution : Ensure all wiring is inside the instrument while replacing cover.	Annotation	Published	10/04/2022 11:10 AM
307 - Replace front cover	Instruction	Published	07/20/2021 3:57 PM
310 - 309 - Tighten four (4) cover screws; Remark:417	Procedure Step	Published	08/11/2021 2:04 PM
569 - Caution : Do not overtighten screws.	Annotation	Published	06/16/2021 2:31 PM
309 - Tighten four (4) cover screws	Instruction	Published	07/22/2021 1:02 PM
417 - Use a medium Phillips (PH2) screwdriver.	Remark	Published	07/22/2021 1:18 PM
312 - 311 - Verify instrument charges successfully; Remark:	Procedure Step	Published	07/20/2021 10:53 AM
311 - Verify instrument charges successfully	Instruction	Published	07/20/2021 10:44 AM
316 - 315 - Connect charger; Remark:289	Procedure Step	Published	07/29/2021 3:07 PM
315 - Connect charger	Instruction	Published	07/20/2021 10:45 AM
289 - Plug charger into instrument and AC power outlet	Remark	Published	07/20/2021 10:48 AM
739 - 737 - Observe smart charger status; Remark:735	Procedure Step	Published	08/11/2021 3:12 PM
737 - Observe smart charger status	Instruction	Published	08/11/2021 12:10 PM
735 - The charger has a blinking yellow light when it is charging	Remark	Published	08/11/2021 12:11 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
20 minutes	Duration	Published	05/18/2020 5:44 PM
As Needed	Frequency	Published	04/01/2020 11:36 AM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Needle nose pliers	Tools	Published	05/06/2020 4:10 PM
Scissors	Tools	Published	05/19/2020 1:54 PM
Utility knife	Tools	Published	05/19/2020 1:54 PM
PRM-470_Partial_Power_Button_Red_Highlight.png	Image	Published	06/18/2021 6:28 PM
PRM470_Remove_Screws_Top_Case	Image	Published	05/08/2020 6:05 PM
PRM-470_di_CGN_open_00536	Image	Published	02/19/2023 11:26 AM
PRM470_Battery_connection_is_labeled_1	Image	Published	02/19/2023 10:40 AM
PRM-470_Disconnect_battery	Image	Published	05/09/2020 8:40 PM
PRM-470_Unbundle_wires	Image	Published	05/19/2020 3:00 PM
PRM-470 Detach port from case	Image	Published	05/19/2020 3:19 PM
PRM-470 - Remove old charging port	Image	Published	05/19/2020 3:22 PM
PRM-470 - Insert new charging port	Image	Published	05/19/2020 3:25 PM
PRM-470 - Secure new charging port	Image	Published	05/19/2020 3:30 PM
PRM-470_Reconnect_battery	Image	Published	05/10/2020 8:16 PM
PRM-470 - Bind wiring together	Image	Published	05/19/2020 3:52 PM
PRM-470_Tighten_4_cover_screws	Image	Published	05/10/2020 8:22 PM
PRM-470 Port for Charging Cord Red Arrow	Image	Published	05/09/2020 1:49 PM
PRM-470 Charger_New Wall Plug Red Arrow	Image	Published	05/09/2020 1:47 PM
PRM-470 - Smart Charger Light	Image	Published	05/19/2020 4:14 PM

Read more about PRM-470 Charging Port Replacement

Subscribe to Utility knife