Ladder: 2 meters, 6 feet tall; non-conducting

RPM Cabinet Door Gasket Replacement

Last Updated: 04/23/2025 1:43 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan CM-267 Conveyor Monitor	Device	Published	06/27/2024 1:02 PM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
1402 - 7927 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/30/2022 1:47 PM
7927 - Establish Initial Conditions	Instruction	Published	07/12/2023 12:23 AM
10199 - 10198 - Assess if weather conditions are suitable to complete the full procedure ...; Remark:10197	Procedure Step	Published	10/24/2023 8:01 PM
10198 - Assess if weather conditions are suitable to complete the full procedure ...	Instruction	Published	10/24/2023 8:00 PM
10197 - If the temperature is below 10°C (50°F) or the door is damp due to rain or ...	Remark	Published	10/24/2023 8:01 PM
7268 - 7231 - Close lane; Remark:7233	Procedure Step	Published	04/27/2023 7:01 PM
9053 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	09/27/2023 9:09 AM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
10196 - 10192 - Remove Old Gasket; Remark:	Procedure Step	Published	10/24/2023 8:05 PM
10192 - Remove Old Gasket	Instruction	Published	10/24/2023 8:02 PM
10188 - 10187 - Use putty knife to scrape gasket from door; Remark:10186	Procedure Step	Published	10/24/2023 8:06 PM
10193 - Note : Replacement gasket must be obtained prior to starting. The peel and stick gas...	Annotation	Published	10/24/2023 8:03 PM
10194 - Note : May be ordered from Rapiscan on a “per foot” basis, Part No. 6987G.	Annotation	Published	10/24/2023 8:03 PM
10195 - Note : For ordering, the total length required is shown in Total Gasket Length table...	Annotation	Published	10/24/2023 8:05 PM
10187 - Use putty knife to scrape gasket from door	Instruction	Published	10/24/2023 8:06 PM
10186 - Use care to not scrape the paint.	Remark	Published	10/24/2023 8:06 PM
10189 - 10185 - Discard loose material; Remark:	Procedure Step	Published	10/24/2023 8:07 PM
10185 - Discard loose material	Instruction	Published	10/24/2023 8:07 PM
10190 - 10184 - Apply acetone directly onto residue; Remark:10182	Procedure Step	Published	10/24/2023 8:08 PM
10184 - Apply acetone directly onto residue	Instruction	Published	10/24/2023 8:08 PM
10182 - Either spray or squirt Acetone onto residue and allow soaking for a few minut...	Remark	Published	10/24/2023 8:08 PM
10183 - Use care to not scrape the paint. A razor blade and acetone may be necessary ...	Remark	Published	10/24/2023 8:08 PM
10191 - 10181 - Remove any remaining adhesive; Remark:10180	Procedure Step	Published	10/24/2023 8:09 PM
10181 - Remove any remaining adhesive	Instruction	Published	10/24/2023 8:09 PM
10180 - Use additional acetone and paper towels as needed.	Remark	Published	10/24/2023 8:09 PM
10179 - 10178 - Prep Area for Install of New Gasket; Remark:	Procedure Step	Published	10/24/2023 8:11 PM
10178 - Prep Area for Install of New Gasket	Instruction	Published	10/24/2023 8:11 PM
10175 - 10174 - Clean affected surface with rubbing alcohol and paper towels; Remark:10173	Procedure Step	Published	10/24/2023 8:12 PM
10174 - Clean affected surface with rubbing alcohol and paper towels	Instruction	Published	10/24/2023 8:12 PM
10173 - Remaining adhesive will become slightly sticky.	Remark	Published	10/24/2023 8:12 PM
10176 - 10172 - Wait until conditions are optimal; Remark:10169	Procedure Step	Published	10/24/2023 8:15 PM
10172 - Wait until conditions are optimal	Instruction	Published	10/24/2023 8:13 PM
10169 - To help promote a strong bond, the surface area needs to be free of the origi...	Remark	Published	10/24/2023 8:13 PM
10170 - If the temperature is below 10°C (50°F) or the door is damp due to rain or ...	Remark	Published	10/24/2023 8:14 PM
10171 - If removing the doors, be sure to protect the electronics and detectors from ...	Remark	Published	10/24/2023 8:14 PM
10177 - 10167 - Measure and cut appropriate lengths of gasket material required; Remark:10164	Procedure Step	Published	10/24/2023 8:18 PM
10168 - Caution : Incomplete seals may cause environmental damage to the cabinet contents. Gask...	Annotation	Published	10/24/2023 8:18 PM
10167 - Measure and cut appropriate lengths of gasket material required	Instruction	Published	10/24/2023 8:15 PM
10164 - Use scissors and measuring tape.	Remark	Published	10/24/2023 8:16 PM
10165 - Use Gasket Segment Lengths table for appropriate gasket lengths.	Remark	Published	10/24/2023 8:16 PM
10166 - Suggested technique is to add 3-5 cm to the listed length for the initial cut...	Remark	Published	10/24/2023 8:17 PM
10202 - Gasket Segment Lengths	Remark	Published	10/24/2023 8:31 PM
10203 - 10200 - Mark gasket location on door using attached drawing; Remark:	Procedure Step	Published	10/24/2023 8:34 PM
10201 - Standard : The gasket spacing to the door edge on the top, lock side, and bottom is appr...	Annotation	Published	10/24/2023 8:34 PM
10200 - Mark gasket location on door using attached drawing	Instruction	Published	10/24/2023 8:33 PM
10230 - 10229 - Preheat gasket and/or contact area; Remark:10228	Procedure Step	Published	10/24/2023 9:28 PM
10229 - Preheat gasket and/or contact area	Instruction	Published	10/24/2023 9:28 PM
10228 - Use a hair dryer or similar device until gasket is warm to your touch. This w...	Remark	Published	10/24/2023 9:28 PM
10227 - 10226 - Install New Gasket; Remark:10225	Procedure Step	Published	10/24/2023 9:34 PM
10226 - Install New Gasket	Instruction	Published	10/24/2023 9:29 PM
10225 - gasket application order	Remark	Published	10/24/2023 9:34 PM
10221 - 10220 - Peel protective paper backing from top gasket and attach adhesive side of gas...; Remark:10219	Procedure Step	Published	10/24/2023 9:36 PM
10314 - Caution : Do not stretch or pull the gaskets when placing them on the door as this can ...	Annotation	Published	11/17/2023 8:56 AM
10315 - Note : Attaching the gaskets to the door in the correct sequence is important to kee...	Annotation	Published	11/17/2023 8:57 AM
10220 - Peel protective paper backing from top gasket and attach adhesive side of gas...	Instruction	Published	10/24/2023 9:36 PM
10219 - (This is the first application.) Use care when removing/peeling backing paper...	Remark	Published	10/24/2023 9:36 PM
10222 - 10218 - Peel protective paper backing from side gasket and attach adhesive side of ga...; Remark:10217	Procedure Step	Published	10/24/2023 9:37 PM
10218 - Peel protective paper backing from side gasket and attach adhesive side of ga...	Instruction	Published	10/24/2023 9:36 PM
10217 - (This is the second application.)	Remark	Published	10/24/2023 9:37 PM
10223 - 10216 - Peel protective paper backing from side gasket and attach adhesive side of ga...; Remark:10215	Procedure Step	Published	10/24/2023 9:38 PM
10216 - Peel protective paper backing from side gasket and attach adhesive side of ga...	Instruction	Published	10/24/2023 9:38 PM
10215 - (This is the third application.)	Remark	Published	10/24/2023 9:38 PM
10224 - 10214 - Peel protective paper backing from bottom gasket and attach adhesive side of ...; Remark:10213	Procedure Step	Published	10/24/2023 9:40 PM
10214 - Peel protective paper backing from bottom gasket and attach adhesive side of ...	Instruction	Published	10/24/2023 9:39 PM
10213 - (This is the fourth application.)	Remark	Published	10/24/2023 9:39 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
10210 - 10209 - Close cabinet door; Remark:	Procedure Step	Published	10/24/2023 9:42 PM
10209 - Close cabinet door	Instruction	Published	10/24/2023 9:42 PM
10211 - 10207 - Keep door closed for at least 24 hours; Remark:10206	Procedure Step	Published	10/24/2023 9:44 PM
10208 - Note : Cure times vary depending on temperature and humidity.	Annotation	Published	10/24/2023 9:44 PM
10207 - Keep door closed for at least 24 hours	Instruction	Published	10/24/2023 9:43 PM
10206 - The constant pressure of the door will help create a strong bond during the 2...	Remark	Published	10/24/2023 9:44 PM
10212 - 10205 - Check gasket adhesion at end of 24 hours; Remark:10204	Procedure Step	Published	10/24/2023 9:46 PM
10205 - Check gasket adhesion at end of 24 hours	Instruction	Published	10/24/2023 9:45 PM
10204 - Check temperature or cleanliness of surface if gasket does not adhere properl...	Remark	Published	10/24/2023 9:46 PM
8260 - 8250 - Reopen Lane; Remark:8249	Procedure Step	Published	09/07/2023 3:09 PM
8250 - Reopen Lane	Instruction	Published	09/07/2023 3:09 PM
8249 - Remove orange safety (traffic control) cones	Remark	Published	09/07/2023 3:09 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
hours	Duration	Published	05/26/2022 11:45 AM
Upon damage or no longer sealing properly	Frequency	Published	10/23/2023 3:03 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Standard	Annotation Type	Published	03/02/2020 3:25 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Narrow putty knife or paint scraper	Tools	Published	10/23/2023 4:18 PM
Razor blade scraper	Tools	Published	10/23/2023 4:18 PM
Measuring Tape	Tools	Published	10/03/2023 10:11 AM
Scissors	Tools	Published	05/19/2020 1:54 PM
Permanent marker	Tools	Published	10/23/2023 10:07 AM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Ladder: 2 meters, 6 feet tall; non-conducting	Replacement Parts	Published	09/01/2023 9:34 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
safety glasses	Replacement Parts	Published	07/02/2023 4:48 PM
Gloves	Replacement Parts	Published	05/10/2023 3:28 PM
Gasket segment lengths_0.png	Image	Published	10/24/2023 9:23 PM
gasket application order	Image	Published	10/24/2023 9:33 PM

Read more about RPM Cabinet Door Gasket Replacement

RPM VD-580 Replacement

Last Updated: 04/23/2025 1:42 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan CM-267 Conveyor Monitor	Device	Published	06/27/2024 1:02 PM
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
7264 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	04/27/2023 7:00 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7622 - 7592 - Inform system operators; Remark:11335	Procedure Step	Published	04/20/2025 10:15 AM
7592 - Inform system operators	Instruction	Published	06/29/2023 3:20 PM
11335 - Upon arrival, brief system operators on expected work, duration, anticipated ...	Remark	Published	04/20/2025 10:14 AM
7268 - 7231 - Close lane; Remark:7233	Procedure Step	Published	04/27/2023 7:01 PM
9053 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	09/27/2023 9:09 AM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7269 - 7232 - Open RPM door; Remark:7234	Procedure Step	Published	04/27/2023 7:02 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7234 - Open all doors needed to access components.	Remark	Published	04/19/2025 7:48 PM
7755 - 7679 - Disconnect Ethernet; Remark:11336	Procedure Step	Published	04/20/2025 11:18 AM
7680 - Caution : Make sure to press release button on back of Ethernet cable before removing.	Annotation	Published	07/01/2023 11:54 PM
7679 - Disconnect Ethernet	Instruction	Published	07/01/2023 11:52 PM
11336 - Locate Ethernet connector on top of SC-770 controller. Press release button o...	Remark	Published	04/20/2025 11:21 AM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
9283 - 8309 - Remove VD-580; Remark:	Procedure Step	Published	10/02/2023 1:35 PM
8309 - Remove VD-580	Instruction	Published	09/08/2023 2:31 PM
9279 - 9207 - Disconnect BNC and MHV cables from VD-580 on top of gamma detector; Remark:	Procedure Step	Published	10/02/2023 1:35 PM
7792 - Note : It is good engineering practice to ensure all cables and connectors are label...	Annotation	Published	07/07/2023 2:17 PM
9207 - Disconnect BNC and MHV cables from VD-580 on top of gamma detector	Instruction	Published	10/03/2023 10:40 AM
9280 - 9208 - Unhook springs from photomultiplier tube ...; Remark:	Procedure Step	Published	10/02/2023 1:36 PM
9221 - Note : Do not release the springs while they are under tension, the springs may fly ...	Annotation	Published	09/29/2023 5:40 PM
9208 - Unhook springs from photomultiplier tube (PMT) using needle nose pliers	Instruction	Published	10/03/2023 11:57 AM
9281 - 9209 - Pull VD-580 off gently to remove from PMT; Remark:9518	Procedure Step	Published	10/02/2023 1:36 PM
9209 - Pull VD-580 off gently to remove from PMT	Instruction	Published	10/03/2023 11:57 AM
9518 -	Remark	Published	10/04/2023 10:28 AM
9282 - 9210 - Verify VD-580 to be installed is potted; Remark:9218	Procedure Step	Published	10/02/2023 1:37 PM
9210 - Verify VD-580 to be installed is potted	Instruction	Published	10/03/2023 11:59 AM
9218 - Potted version has visible gel coating on circuit board.	Remark	Published	10/03/2023 1:21 PM
9219 - Potted Version	Remark	Published	10/03/2023 1:20 PM
9278 - 9211 - Install New VD-580; Remark:	Procedure Step	Published	10/02/2023 1:37 PM
9211 - Install New VD-580	Instruction	Published	09/29/2023 5:32 PM
9275 - 9212 - Line up alignment key and notch between PMT and VD‑580; Remark:9519	Procedure Step	Published	10/02/2023 1:38 PM
9212 - Line up alignment key and notch between PMT and VD‑580	Instruction	Published	10/03/2023 12:00 PM
9519 -	Remark	Published	10/04/2023 10:51 AM
9276 - 9213 - Firmly press VD-580 into place on PMT and...; Remark:	Procedure Step	Published	10/02/2023 1:38 PM
9222 - Note : It may be easier to install the rear spring first. You can install that spring b...	Annotation	Published	10/03/2023 10:39 AM
9213 - Firmly press VD-580 into place on PMT and reattach springs	Instruction	Published	10/03/2023 12:01 PM
9277 - 9214 - Reconnect BNC and MHV cables to VD-580; Remark:	Procedure Step	Published	10/02/2023 1:38 PM
7811 - Caution : Proper connection of cables is critical.	Annotation	Published	07/07/2023 9:48 PM
9214 - Reconnect BNC and MHV cables to VD-580	Instruction	Published	09/29/2023 5:33 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
9272 - 9215 - Verify detector count rate; Remark:9220	Procedure Step	Published	04/20/2025 11:49 AM
9215 - Verify detector count rate	Instruction	Published	09/29/2023 5:34 PM
9220 - Navigate to SHOW COUNTS on SC-770. Enter “Program Mode” by pres...	Remark	Published	04/20/2025 11:51 AM
7781 - 7730 - Reconnect Ethernet; Remark:7731	Procedure Step	Published	04/20/2025 11:00 AM
7730 - Reconnect Ethernet	Instruction	Published	07/02/2023 2:34 AM
7731 - Insert Ethernet connector at top of SC-770 module. Connector will audibly "cl...	Remark	Published	07/02/2023 2:36 AM
9273 - 9216 - Reopen RPM Lane; Remark:	Procedure Step	Published	10/02/2023 1:40 PM
9216 - Reopen RPM Lane	Instruction	Published	09/29/2023 5:34 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
10 minutes	Duration	Published	04/01/2020 11:35 AM
Change from non-potted to potted parts once	Frequency	Published	10/02/2023 1:52 PM
Upon failure of VD-580	Frequency	Published	10/02/2023 1:50 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Reflective safety vest if required	Replacement Parts	Published	06/20/2023 4:47 PM
Ladder: 2 meters, 6 feet tall; non-conducting	Replacement Parts	Published	09/01/2023 9:34 PM
Traffic control cones or equivalent if required	Replacement Parts	Published	06/20/2023 4:47 PM
safety glasses	Replacement Parts	Published	07/02/2023 4:48 PM
Needle nose pliers	Tools	Published	05/06/2020 4:10 PM
Disconnect Ethernet cable on top of SC-770 box	Image	Published	10/04/2023 2:59 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Pull VD-580 off gently to remove from PMT	Image	Published	10/16/2023 10:15 AM
Potted version has visible gel coating on circuit board.	Image	Published	10/02/2023 3:39 PM
Line up alignment key and notch between PMT and VD 580	Image	Published	10/02/2023 3:40 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM

Read more about RPM VD-580 Replacement

RPM Banner IR Occupancy Sensor Replacement

Last Updated: 04/23/2025 1:42 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
8468 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/16/2023 4:47 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7268 - 7231 - Close lane; Remark:7233	Procedure Step	Published	04/27/2023 7:01 PM
9053 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	09/27/2023 9:09 AM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7269 - 7232 - Open RPM door; Remark:7234	Procedure Step	Published	04/27/2023 7:02 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7234 - Open all doors needed to access components.	Remark	Published	04/19/2025 7:48 PM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
8623 - 8613 - Uninstall Faulty Sensor; Remark:	Procedure Step	Published	09/19/2023 12:06 PM
8613 - Uninstall Faulty Sensor	Instruction	Published	09/19/2023 11:40 AM
8624 - 8614 - Locate infrared sensors; Remark:8615	Procedure Step	Published	09/19/2023 5:39 PM
8614 - Locate infrared sensors	Instruction	Published	09/19/2023 11:41 AM
8615 - Typical sensor locations are as follows: Control pillar hou...	Remark	Published	09/19/2023 11:43 AM
8625 - 8617 - Disconnect applicable infrared sensors; Remark:8618	Procedure Step	Published	09/19/2023 12:08 PM
8617 - Disconnect applicable infrared sensors	Instruction	Published	09/19/2023 11:49 AM
8618 - To disconnect sensor cable, turn collar counterclockwise and pull away from s...	Remark	Published	09/19/2023 11:51 AM
8626 - 8619 - Unscrew mounting nut; Remark:8620	Procedure Step	Published	09/19/2023 12:09 PM
8619 - Unscrew mounting nut	Instruction	Published	09/19/2023 11:59 AM
8620 - Rotate threaded nut counterclockwise. It may be necessary to hold the infrare...	Remark	Published	09/19/2023 11:58 AM
8627 - 8621 - Remove sensor from back of door; Remark:8622	Procedure Step	Published	09/19/2023 12:09 PM
8621 - Remove sensor from back of door	Instruction	Published	09/19/2023 12:01 PM
8622 - Removal of infrared sensor	Remark	Published	09/19/2023 12:03 PM
8660 - 8658 - Retain sensor O-ring; Remark:8659	Procedure Step	Published	09/19/2023 5:56 PM
8658 - Retain sensor O-ring	Instruction	Published	09/19/2023 5:55 PM
8659 - Retain Sensor O-ring	Remark	Published	09/19/2023 5:55 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
8641 - 8628 - Install New Sensor; Remark:	Procedure Step	Published	09/19/2023 4:09 PM
8628 - Install New Sensor	Instruction	Published	09/19/2023 12:35 PM
8642 - 8629 - Verify replacement sensor matches function and color of sensor previously rem...; Remark:8630	Procedure Step	Published	09/19/2023 4:10 PM
8629 - Verify replacement sensor matches function and color of sensor previously rem...	Instruction	Published	09/19/2023 12:36 PM
8630 - Infrared sensor identification	Remark	Published	09/19/2023 12:48 PM
8643 - 8631 - Remove nut closest to sensor face; Remark:8632	Procedure Step	Published	09/19/2023 4:11 PM
8631 - Remove nut closest to sensor face	Instruction	Published	09/19/2023 12:48 PM
8632 - Infrared Nut	Remark	Published	09/19/2023 12:50 PM
8644 - 8633 - Add retained O-ring; Remark:8634	Procedure Step	Published	09/19/2023 4:12 PM
8633 - Add retained O-ring	Instruction	Published	09/19/2023 3:52 PM
8634 - Infrared Sensor O-ring	Remark	Published	09/19/2023 3:55 PM
8645 - 8635 - Mount new infrared sensor; Remark:8636	Procedure Step	Published	09/19/2023 4:13 PM
8635 - Mount new infrared sensor	Instruction	Published	09/19/2023 3:57 PM
8636 - Insert sensor through hole on the back side of door.	Remark	Published	09/19/2023 4:01 PM
8646 - 8638 - Add outside nut to front and hand tighten; Remark:8639	Procedure Step	Published	09/19/2023 4:14 PM
8637 - Note : The nut on the outside should be flush with the sensor.	Annotation	Published	09/19/2023 4:01 PM
8638 - Add outside nut to front and hand tighten	Instruction	Published	09/19/2023 4:02 PM
8639 - Use the adjustable wrench to snug the nut up slightly, just enough for the ga...	Remark	Published	09/19/2023 4:05 PM
8647 - 8661 - Reconnect applicable cable previously removed in Step 4-6; Remark:8559	Procedure Step	Published	09/19/2023 4:15 PM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	10/28/2022 2:19 PM
8661 - Reconnect applicable cable previously removed in Step 4-4	Instruction	Published	09/19/2023 6:14 PM
8559 - To reconnect sensor cable, align connectors, push towards sensor, and turn co...	Remark	Published	09/29/2023 12:05 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
8503 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	09/16/2023 9:00 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7281 - 7252 - Verify RPM start-up; Remark:7253	Procedure Step	Published	04/20/2025 3:26 PM
7252 - Verify RPM start-up	Instruction	Published	04/27/2023 2:23 PM
7253 - RPM will perform a power on self-test (POST) and collect a background radiati...	Remark	Published	05/10/2023 3:14 PM
8654 - 8648 - Verify SC-770 display shows OCCUPIED when infrared beams are...; Remark:8651	Procedure Step	Published	09/19/2023 4:52 PM
8648 - Verify SC-770 display shows OCCUPIED when infrared beams are...	Instruction	Published	09/19/2023 4:23 PM
8651 - SC-770 Occupied	Remark	Published	09/19/2023 4:30 PM
8655 - 8649 - Test sensors independently; Remark:8650	Procedure Step	Published	09/19/2023 4:53 PM
8649 - Test sensors independently	Instruction	Published	09/19/2023 4:24 PM
8650 - Disconnect one receiver cable, shut door, and clear sensors for five (5) seco...	Remark	Published	09/19/2023 4:28 PM
8656 - 8648 - Verify SC-770 display shows OCCUPIED when infrared beams are...; Remark:8651	Procedure Step	Published	09/19/2023 4:54 PM
8653 - 8652 - Repeat steps 4-4 through 4-6 for other receiver sensors.; Remark:	Procedure Step	Published	04/13/2025 6:16 PM
8652 - Repeat steps 4-4 through 4-6 for other receiver sensors.	Instruction	Published	04/13/2025 6:11 PM
7282 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	04/27/2023 4:15 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
30 minutes	Duration	Published	04/01/2020 11:35 AM
If system is locked in continuous occupancy or speed indication does not function	Frequency	Published	09/19/2023 5:28 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Adjustable wrench	Replacement Parts	Published	06/02/2023 10:08 PM
Ladder: 2 meters, 6 feet tall; non-conducting	Replacement Parts	Published	09/01/2023 9:34 PM
Reflective safety vest if required	Replacement Parts	Published	06/20/2023 4:47 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Remove Infrared Sensor Nut	Image	Published	09/19/2023 11:57 AM
Mount Infrared Sensors	Image	Published	09/19/2023 5:51 PM
Retained Infrared O-ring	Image	Published	09/19/2023 5:44 PM
Infrared Sensor Identification	Image	Published	09/19/2023 12:39 PM
Outside Nut of Infrared Sensor	Image	Published	09/19/2023 12:49 PM
Tighten Infrared Sensor Nut	Image	Published	09/19/2023 4:03 PM
Infrared Connection	Image	Published	09/29/2023 12:02 PM
Infrared Cable Installation	Image	Published	09/17/2023 10:12 PM
Infrared Sensor Cable	Image	Published	09/17/2023 10:13 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
SC-770 Occupied	Image	Published	09/19/2023 4:30 PM

Read more about RPM Banner IR Occupancy Sensor Replacement

RPM Neutron Detector Helium-3 (He3) Tube Replacement

Last Updated: 04/23/2025 1:42 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
7621 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	06/29/2023 5:37 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7268 - 7231 - Close lane; Remark:7233	Procedure Step	Published	04/27/2023 7:01 PM
9053 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	09/27/2023 9:09 AM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7269 - 7232 - Open RPM door; Remark:7234	Procedure Step	Published	04/27/2023 7:02 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7234 - Open all doors needed to access components.	Remark	Published	04/19/2025 7:48 PM
7454 - 7290 - Disable tamper switches; Remark:7416	Procedure Step	Published	06/02/2023 5:25 PM
7290 - Disable tamper switches	Instruction	Published	05/01/2023 8:14 AM
7416 - Use a magnet to disable tamper switches for all open doors. Use adhesive tape...	Remark	Published	06/02/2023 1:18 PM
8561 - 7291 - Disable both infrared occupancy sensors; Remark:8514	Procedure Step	Published	09/18/2023 12:05 AM
5291 - Note : It is good practice to verify all cables and connectors are labeled prior to ...	Annotation	Published	10/24/2022 8:35 AM
7291 - Disable both infrared occupancy sensors	Instruction	Published	05/01/2023 8:15 AM
8514 - Verify sensors mounted in control pillar door are receivers.	Remark	Published	09/29/2023 11:52 AM
9205 - To disconnect sensor cable, turn collar counterclockwise and pull away from s...	Remark	Published	09/29/2023 11:52 AM
8221 - 7676 - Brief system operators on expected work, duration, anticipated alarms, and fa...; Remark:	Procedure Step	Published	09/01/2023 9:26 PM
7676 - Brief system operators on expected work, duration, anticipated alarms, and fa...	Instruction	Published	07/01/2023 11:39 PM
8591 - 8515 - Uninstall Faulty Neutron Tube; Remark:	Procedure Step	Published	09/18/2023 12:10 AM
8515 - Uninstall Faulty Neutron Tube	Instruction	Published	09/17/2023 7:24 PM
8562 - 8516 - Disconnect cable from faulty helium-3 (He3) tube; Remark:8517	Procedure Step	Published	09/17/2023 10:38 PM
8516 - Disconnect cable from faulty helium-3 (He3) tube	Instruction	Published	09/17/2023 7:25 PM
8517 - Push toward connection, turn coupling nut counterclockwise, and pull away fro...	Remark	Published	09/17/2023 7:30 PM
8563 - 8518 - Remove four (4) front panel screws; Remark:8519	Procedure Step	Published	09/17/2023 10:39 PM
8518 - Remove four (4) front panel screws	Instruction	Published	09/17/2023 7:32 PM
8519 - Use a large Phillips (PH3) screwdriver. There should be four (4) screws, but ...	Remark	Published	09/17/2023 7:37 PM
8564 - 6748 - Remove front panel; Remark:	Procedure Step	Published	09/17/2023 10:39 PM
6748 - Remove front panel	Instruction	Published	12/09/2022 3:49 PM
8565 - 8520 - Remove stabilizing brace screws; Remark:8521	Procedure Step	Published	09/17/2023 10:40 PM
8520 - Remove stabilizing brace screws	Instruction	Published	09/17/2023 7:40 PM
8521 - There should be two stabilizing braces for each He3 tube; configurations migh...	Remark	Published	09/17/2023 7:45 PM
8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525	Procedure Step	Published	09/17/2023 10:42 PM
8522 - Caution : Tube may fall out of detector assembly when bracket screw is removed.	Annotation	Published	09/17/2023 7:59 PM
9605 - Note : This step is only needed if cleaning He3 tube from upper detector.	Annotation	Published	04/13/2025 6:03 PM
8523 - Loosen bracket screw (if applicable)	Instruction	Published	09/17/2023 8:00 PM
8525 - If there is more than one screw, completely remove one. Use medium Phillips (...	Remark	Published	09/29/2023 12:12 PM
8567 - 8526 - Rotate bracket (if applicable); Remark:8527	Procedure Step	Published	09/17/2023 10:43 PM
8526 - Rotate bracket (if applicable)	Instruction	Published	09/17/2023 8:13 PM
8527 - Rotate neutron bracket	Remark	Published	04/13/2025 5:58 PM
8568 - 8528 - Remove He3 tube; Remark:8529	Procedure Step	Published	09/17/2023 10:44 PM
8528 - Remove He3 tube	Instruction	Published	09/17/2023 8:24 PM
8529 - Slide tube up through hole and then pull out of moderator.	Remark	Published	04/13/2025 6:11 PM
8569 - 8530 - Remove stabilizing braces; Remark:8531	Procedure Step	Published	09/17/2023 10:45 PM
8530 - Remove stabilizing braces	Instruction	Published	09/17/2023 8:31 PM
8531 - Slide stabilizing braces off He3 tube.	Remark	Published	09/17/2023 8:32 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
8571 - 8533 - Install New He3 Tube; Remark:	Procedure Step	Published	09/17/2023 10:46 PM
8533 - Install New He3 Tube	Instruction	Published	09/17/2023 8:43 PM
8572 - 8534 - Place stabilizing braces onto new He3 tube; Remark:	Procedure Step	Published	09/17/2023 10:47 PM
8534 - Place stabilizing braces onto new He3 tube	Instruction	Published	09/17/2023 8:44 PM
8573 - 8535 - Insert new He3 tube into moderator; Remark:	Procedure Step	Published	09/17/2023 10:48 PM
8535 - Insert new He3 tube into moderator	Instruction	Published	09/17/2023 8:46 PM
8574 - 8526 - Rotate bracket (if applicable); Remark:8536	Procedure Step	Published	09/17/2023 10:48 PM
8536 - Rotate He3 tube bracket	Remark	Published	09/17/2023 8:48 PM
8575 - 8537 - Tighten bracket screw (if applicable); Remark:8538	Procedure Step	Published	09/17/2023 10:49 PM
8537 - Tighten bracket screw (if applicable)	Instruction	Published	09/17/2023 8:50 PM
8538 - Use medium Phillips (PH2) screwdriver.	Remark	Published	09/17/2023 8:51 PM
8576 - 8539 - Reinstall stabilizing braces screws; Remark:8540	Procedure Step	Published	09/17/2023 10:50 PM
8539 - Reinstall stabilizing braces screws	Instruction	Published	09/17/2023 8:53 PM
8540 - Use medium Phillips (PH2) screwdriver.	Remark	Published	09/17/2023 8:54 PM
8577 - 8541 - Reinstall front panel with four (4) screws; Remark:8542	Procedure Step	Published	09/17/2023 10:51 PM
8541 - Reinstall front panel with four (4) screws	Instruction	Published	09/17/2023 8:56 PM
8542 - Use large Phillips (PH3) screwdriver.	Remark	Published	09/17/2023 8:59 PM
8578 - 8543 - Reconnect cable to He3 tube; Remark:8544	Procedure Step	Published	09/17/2023 10:52 PM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	10/28/2022 2:19 PM
8543 - Reconnect cable to He3 tube	Instruction	Published	09/17/2023 9:01 PM
8544 - Rotate to align connector notches. Push toward connection and turn coupling n...	Remark	Published	09/17/2023 9:05 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7281 - 7252 - Verify RPM start-up; Remark:7253	Procedure Step	Published	04/20/2025 3:26 PM
7252 - Verify RPM start-up	Instruction	Published	04/27/2023 2:23 PM
7253 - RPM will perform a power on self-test (POST) and collect a background radiati...	Remark	Published	05/10/2023 3:14 PM
7282 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	04/27/2023 4:15 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
8579 - 8545 - Isolate new He3 tube; Remark:8547	Procedure Step	Published	09/17/2023 10:53 PM
8546 - Caution : Do not disconnect cable from new tube	Annotation	Published	09/17/2023 9:17 PM
8545 - Isolate new He3 tube	Instruction	Published	09/17/2023 9:16 PM
8547 - Disconnect cables from all He3 tubes in moderator (white box) except	Remark	Published	09/17/2023 9:19 PM
8580 - 8548 - Navigate to SHOW COUNTS for neutron channels; Remark:8549	Procedure Step	Published	09/17/2023 10:57 PM
8548 - Navigate to SHOW COUNTS for neutron channels	Instruction	Published	09/17/2023 9:22 PM
8549 - On SC-770, press 01234# Then, press 2:	Remark	Published	09/17/2023 9:26 PM
8581 - 8550 - Place neutron source on neutron detector; Remark:8551	Procedure Step	Published	09/17/2023 10:57 PM
8550 - Place neutron source on neutron detector	Instruction	Published	09/17/2023 9:28 PM
8551 - Secure source to middle of detector with adhesive tape.	Remark	Published	09/17/2023 9:31 PM
8582 - 9606 - Verify counts from cleaned He3 tube; Remark:8553	Procedure Step	Published	09/17/2023 10:58 PM
9606 - Verify counts from cleaned He3 tube	Instruction	Published	10/11/2023 11:33 AM
8553 - Neutron counts will increase on the channel with the new He3 tube	Remark	Published	09/17/2023 9:34 PM
8583 - 2581 - Remove radioactive source; Remark:	Procedure Step	Published	09/17/2023 11:00 PM
2581 - Remove radioactive source	Instruction	Published	08/11/2021 3:52 PM
8584 - 8458 - Exit programming mode; Remark:8554	Procedure Step	Published	09/17/2023 11:00 PM
8458 - Exit programming mode	Instruction	Published	09/15/2023 4:21 PM
8554 - On SC-770, press # button until main controller screen is di...	Remark	Published	09/17/2023 9:40 PM
8585 - 8555 - Reconnect all neutron detectors; Remark:8556	Procedure Step	Published	09/17/2023 11:01 PM
8555 - Reconnect all neutron detectors	Instruction	Published	09/17/2023 9:53 PM
8556 - Connecting neutron cable	Remark	Published	09/17/2023 9:55 PM
8586 - 8557 - Perform functional compliance test; Remark:8558	Procedure Step	Published	09/17/2023 11:02 PM
8557 - Perform functional compliance test	Instruction	Published	09/17/2023 10:00 PM
8558 - DET-RPM-RAP-RM05, RPM Functional Compliance Test.	Remark	Published	09/17/2023 10:02 PM
8588 - 7305 - Enable both infrared occupancy sensors; Remark:8559	Procedure Step	Published	09/17/2023 11:04 PM
7305 - Enable both infrared occupancy sensors	Instruction	Published	05/01/2023 8:33 AM
8559 - To reconnect sensor cable, align connectors, push towards sensor, and turn co...	Remark	Published	09/29/2023 12:05 PM
8589 - 7310 - Enable tamper switches; Remark:7348	Procedure Step	Published	09/17/2023 11:07 PM
7310 - Enable tamper switches	Instruction	Published	05/01/2023 8:36 AM
7348 - Remove all magnets and/or adhesive tape from door switches.	Remark	Published	09/17/2023 10:23 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
minutes	Duration	Published	05/26/2022 11:41 AM
Upon failure of neutron detector He3 tube	Frequency	Published	09/17/2023 11:37 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Magnets and adhesive tape to disable door tamper switches	Replacement Parts	Published	06/02/2023 10:08 PM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Large Phillips (PH3) screwdriver	Tools	Published	09/17/2023 11:37 PM
Ladder: 2 meters, 6 feet tall; non-conducting	Replacement Parts	Published	09/01/2023 9:34 PM
Orange/yellow safety vest	Replacement Parts	Published	04/27/2023 6:56 PM
Safety shoes	Replacement Parts	Published	04/27/2023 6:56 PM
Gloves	Replacement Parts	Published	05/10/2023 3:28 PM
Protective headwear: glasses, hard hat	Replacement Parts	Published	05/10/2023 3:31 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
Disable tamper switch	Image	Published	09/07/2023 8:22 PM
Disable Tamper Switch	Image	Published	06/02/2023 2:28 PM
Infrared Receiver	Image	Published	09/17/2023 7:09 PM
Infrared Receiver DC	Image	Published	09/29/2023 11:47 AM
Infrared Disconnect Sensor Cable	Image	Published	09/17/2023 7:11 PM
Infrared Sensor Disconnect	Image	Published	09/17/2023 7:12 PM
Neutron Connector Removal	Image	Published	09/17/2023 7:28 PM
Neutron Panel Screws	Image	Published	09/17/2023 7:36 PM
Neutron Brace	Image	Published	09/17/2023 7:45 PM
Loosen Neutron Bracket	Image	Published	09/17/2023 7:53 PM
Loosen Neutron Bracket	Image	Published	09/17/2023 7:54 PM
Rotate Neutron Bracket_1	Image	Published	09/17/2023 7:56 PM
Rotate Neutron Bracket	Image	Published	09/17/2023 7:57 PM
Remove He3 Tube	Image	Published	09/17/2023 8:22 PM
Pull He3 Tube	Image	Published	09/17/2023 8:23 PM
Remove He3 Tube Braces	Image	Published	09/17/2023 8:29 PM
Return Rotated Neutron Bracket	Image	Published	09/17/2023 8:41 PM
Reconnect Neutron Cables	Image	Published	09/17/2023 9:03 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
Source on Neutron Detector	Image	Published	09/17/2023 9:29 PM
SC-770 Neutron Counts	Image	Published	09/17/2023 9:34 PM
Infrared Connection	Image	Published	09/29/2023 12:02 PM
Infrared Cable Installation	Image	Published	09/17/2023 10:12 PM
Infrared Sensor Cable	Image	Published	09/17/2023 10:13 PM
Remove all magnets and or adhesive tape from door switches	Image	Published	09/08/2023 4:18 PM
Remove Magnet on Tamper Switch	Image	Published	06/02/2023 4:31 PM

Read more about RPM Neutron Detector Helium-3 (He3) Tube Replacement

RPM Gamma Detector Replacement

Last Updated: 04/23/2025 1:41 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
7621 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	06/29/2023 5:37 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7268 - 7231 - Close lane; Remark:7233	Procedure Step	Published	04/27/2023 7:01 PM
9053 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	09/27/2023 9:09 AM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7269 - 7232 - Open RPM door; Remark:7234	Procedure Step	Published	04/27/2023 7:02 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7234 - Open all doors needed to access components.	Remark	Published	04/19/2025 7:48 PM
7454 - 7290 - Disable tamper switches; Remark:7416	Procedure Step	Published	06/02/2023 5:25 PM
7290 - Disable tamper switches	Instruction	Published	05/01/2023 8:14 AM
7416 - Use a magnet to disable tamper switches for all open doors. Use adhesive tape...	Remark	Published	06/02/2023 1:18 PM
8281 - 8280 - Disable both infrared occupancy sensors; Remark:8279	Procedure Step	Published	09/07/2023 8:39 PM
7351 - Note : It is good practice to verify all cables and connectors are labeled prior to ...	Annotation	Published	05/03/2023 11:25 AM
8280 - Disable both infrared occupancy sensors	Instruction	Published	09/07/2023 8:31 PM
8279 - Verify sensors mounted in control pillar door are receivers	Remark	Published	09/07/2023 8:39 PM
8287 - To disconnect sensor cable, turn collar counterclockwise and pull away from s...	Remark	Published	09/08/2023 12:34 PM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
8286 - 8285 - Uninstall VD-580; Remark:	Procedure Step	Published	09/08/2023 12:39 PM
8285 - Uninstall VD-580	Instruction	Published	09/08/2023 12:38 PM
8284 - 8283 - Disconnect BNC and MHV cables; Remark:8282	Procedure Step	Published	09/08/2023 12:45 PM
7352 - Note : It is good practice to verify all cables and connectors are labeled prior to ...	Annotation	Published	05/03/2023 11:27 AM
8283 - Disconnect BNC and MHV cables	Instruction	Published	09/08/2023 12:40 PM
8282 - Push toward connection, turn coupling nut counterclockwise, and pull away fro...	Remark	Published	09/08/2023 12:45 PM
8313 - 8311 - Remove three (3) mounting springs; Remark:8310	Procedure Step	Published	09/08/2023 2:28 PM
8312 - Note : Take care when removing springs, as they might snap back and become misplaced...	Annotation	Published	09/08/2023 2:28 PM
8311 - Remove three (3) mounting springs	Instruction	Published	09/08/2023 2:22 PM
8310 - Use needle nose pliers. Retain springs for reinstallation.	Remark	Published	09/08/2023 2:28 PM
8314 - 8309 - Remove VD-580; Remark:8308	Procedure Step	Published	09/08/2023 2:41 PM
8309 - Remove VD-580	Instruction	Published	09/08/2023 2:31 PM
8308 - Pull VD-580, using small side-to-side motion.	Remark	Published	09/08/2023 2:40 PM
8307 - 8306 - Uninstall faulty gamma detector; Remark:	Procedure Step	Published	09/08/2023 2:45 PM
8306 - Uninstall faulty gamma detector	Instruction	Published	09/08/2023 2:45 PM
8302 - 8301 - Remove metal brackets; Remark:8300	Procedure Step	Published	09/08/2023 2:52 PM
8301 - Remove metal brackets	Instruction	Published	09/08/2023 2:47 PM
8300 - Use small Phillips (PH1) screwdriver. Retain brackets and screws	Remark	Published	09/08/2023 2:51 PM
8303 - 8298 - Remove securing straps; Remark:8297	Procedure Step	Published	09/08/2023 3:00 PM
8299 - Caution : Detector may fall out of lead shielding when brackets and straps are removed....	Annotation	Published	09/08/2023 3:00 PM
8298 - Remove securing straps	Instruction	Published	09/08/2023 2:54 PM
8297 - Do NOT cut straps. Straps may be hook and loop (Velcro) or cable ties. Some w...	Remark	Published	09/08/2023 2:59 PM
8304 - 8296 - Remove faulty gamma detector; Remark:8295	Procedure Step	Published	09/08/2023 3:06 PM
8296 - Remove faulty gamma detector	Instruction	Published	09/08/2023 3:00 PM
8295 -	Remark	Published	09/08/2023 3:06 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
8292 - 8291 - Install new gamma detector; Remark:	Procedure Step	Published	09/08/2023 3:10 PM
8291 - Install new gamma detector	Instruction	Published	09/08/2023 3:10 PM
8290 - 8289 - Set new gamma detector in place; Remark:8288	Procedure Step	Published	09/08/2023 3:24 PM
8289 - Set new gamma detector in place	Instruction	Published	09/08/2023 3:15 PM
8288 -	Remark	Published	09/08/2023 3:24 PM
8333 - 8332 - Fasten securing straps; Remark:8331	Procedure Step	Published	09/08/2023 3:31 PM
8332 - Fasten securing straps	Instruction	Published	09/08/2023 3:30 PM
8331 - Use hook and loop (Velcro) straps or long, heavy-duty cable ties. If cable ti...	Remark	Published	09/08/2023 3:31 PM
8334 - 8330 - Replace metal brackets; Remark:472	Procedure Step	Published	09/08/2023 3:37 PM
8330 - Replace metal brackets	Instruction	Published	09/08/2023 3:31 PM
472 - Use a small Phillips (PH1) screwdriver.	Remark	Published	07/22/2021 1:13 PM
8329 - 8328 - Install VD-580; Remark:	Procedure Step	Published	09/08/2023 3:41 PM
8328 - Install VD-580	Instruction	Published	09/08/2023 3:41 PM
8325 - 8324 - Reconnect VD-580 to photomultiplier tube; Remark:8323	Procedure Step	Published	09/08/2023 3:47 PM
8324 - Reconnect VD-580 to photomultiplier tube	Instruction	Published	09/08/2023 3:42 PM
8323 - The VD-580 has a notch that aligns with the tab on the photomultiplier tube	Remark	Published	09/08/2023 3:47 PM
8326 - 8322 - Reattach mounting springs; Remark:9071	Procedure Step	Published	09/08/2023 3:50 PM
8322 - Reattach mounting springs	Instruction	Published	09/08/2023 3:48 PM
9071 - Use needle nose pliers.	Remark	Published	09/27/2023 9:58 AM
8327 - 8320 - Reconnect BNC and MHV cables; Remark:8319	Procedure Step	Published	09/08/2023 3:56 PM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	10/28/2022 2:19 PM
8320 - Reconnect BNC and MHV cables	Instruction	Published	09/08/2023 3:55 PM
8319 - Ensure cables are connected correctly. Connector placement should not require...	Remark	Published	09/08/2023 3:56 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7468 - 7304 - Confirm RPM has restarted correctly; Remark:7487	Procedure Step	Published	06/02/2023 5:36 PM
7304 - Confirm RPM has restarted correctly	Instruction	Published	05/01/2023 8:31 AM
7487 - The SC-770 controller will display "OK" following Power On Self-Test (POST) a...	Remark	Published	06/02/2023 10:35 PM
7469 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	06/02/2023 5:36 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
7840 - 7816 - Perform electronic alignment; Remark:7817	Procedure Step	Published	07/07/2023 11:12 PM
7816 - Perform electronic alignment	Instruction	Published	07/07/2023 9:55 PM
7817 - DET-RPM-RAP-CM01, RPM Electronic Alignment Procedure.	Remark	Published	04/13/2025 5:55 PM
8317 - 8316 - Enable both infrared occupancy sensors; Remark:8315	Procedure Step	Published	09/08/2023 4:14 PM
7263 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	04/24/2023 2:32 PM
8316 - Enable both infrared occupancy sensors	Instruction	Published	09/08/2023 4:11 PM
8315 - To reconnect sensor cable, align connectors, push towards sensor, and turn th...	Remark	Published	09/08/2023 4:13 PM
8318 - 7450 - Enable tamper switches; Remark:7348	Procedure Step	Published	09/08/2023 4:20 PM
7450 - Enable tamper switches	Instruction	Published	06/02/2023 4:42 PM
7348 - Remove all magnets and/or adhesive tape from door switches.	Remark	Published	09/17/2023 10:23 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
minutes	Duration	Published	05/26/2022 11:41 AM
Upon failure of the gamma detector	Frequency	Published	09/07/2023 7:35 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Magnets and adhesive tape to disable door tamper switches	Replacement Parts	Published	06/02/2023 10:08 PM
Needle nose pliers	Tools	Published	05/06/2020 4:10 PM
Small Phillips (PH1) screwdriver	Tools	Published	05/14/2020 2:48 PM
Ladder: 2 meters, 6 feet tall; non-conducting	Replacement Parts	Published	09/01/2023 9:34 PM
Orange/yellow safety vest	Replacement Parts	Published	04/27/2023 6:56 PM
Safety shoes	Replacement Parts	Published	04/27/2023 6:56 PM
Gloves	Replacement Parts	Published	05/10/2023 3:28 PM
Protective headwear: glasses, hard hat	Replacement Parts	Published	05/10/2023 3:31 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
Disable tamper switch	Image	Published	09/07/2023 8:22 PM
Disable Tamper Switch	Image	Published	06/02/2023 2:28 PM
infrared sensor receiver	Image	Published	09/07/2023 8:37 PM
occupancy sensor receiver	Image	Published	09/07/2023 8:38 PM
Disconnect sensor cable	Image	Published	09/08/2023 12:27 PM
Pull cable away from sensor	Image	Published	09/08/2023 12:33 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Disconnect BNC and MHV cables	Image	Published	09/08/2023 12:44 PM
Remove three mounting springs	Image	Published	09/08/2023 2:26 PM
Remove VD-580	Image	Published	09/08/2023 2:38 PM
Remove metal brackets	Image	Published	09/08/2023 2:50 PM
Remove metal brackets 2	Image	Published	09/08/2023 2:51 PM
Remove securing straps	Image	Published	09/08/2023 2:58 PM
Remove faulty gamma detector	Image	Published	09/08/2023 3:02 PM
Remove faulty gamma detector 2	Image	Published	09/08/2023 3:05 PM
Set new gamma detector in place	Image	Published	09/08/2023 3:17 PM
Reconnect VD-580	Image	Published	09/08/2023 3:45 PM
Reconnect VD-580 (2)	Image	Published	09/08/2023 3:47 PM
Reattach mounting springs	Image	Published	09/27/2023 9:57 AM
Reconnect BNC and MHV cables	Image	Published	09/08/2023 3:54 PM
Reconnect BNC and MHV cables 2	Image	Published	09/08/2023 3:54 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
reconnect occupancy sensors	Image	Published	09/08/2023 4:06 PM
reconnect occupancy sensors 2	Image	Published	09/08/2023 4:08 PM
reconnect occupancy sensors 3	Image	Published	09/08/2023 4:10 PM
Remove all magnets and or adhesive tape from door switches	Image	Published	09/08/2023 4:18 PM
Remove Magnet on Tamper Switch	Image	Published	06/02/2023 4:31 PM

Read more about RPM Gamma Detector Replacement

RPM Rabbit Board Replacement

Last Updated: 04/23/2025 1:41 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
Rapiscan CM-267 Conveyor Monitor	Device	Published	06/27/2024 1:02 PM
7478 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/01/2023 7:48 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7372 - 7231 - Close lane; Remark:7233	Procedure Step	Published	09/01/2023 7:52 PM
7261 - Warning : Traffic should temporarily be rerouted or halted during this procedure to ens...	Annotation	Published	09/28/2023 2:09 PM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7373 - 7232 - Open RPM door; Remark:7267	Procedure Step	Published	09/01/2023 7:55 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7267 - Open all doors needed to access components.	Remark	Published	09/16/2023 4:54 PM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
7386 - 7250 - Power on RPM; Remark:7367	Procedure Step	Published	09/01/2023 7:59 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7367 - Move LD-260 switch to ON position. The PWR ON	Remark	Published	05/11/2023 12:42 PM
7281 - 7252 - Verify RPM start-up; Remark:7253	Procedure Step	Published	04/20/2025 3:26 PM
7252 - Verify RPM start-up	Instruction	Published	04/27/2023 2:23 PM
7253 - RPM will perform a power on self-test (POST) and collect a background radiati...	Remark	Published	05/10/2023 3:14 PM
8199 - 8174 - Record existing SC-770 parameter settings; Remark:8175	Procedure Step	Published	09/01/2023 8:01 PM
8174 - Record existing SC-770 parameter settings	Instruction	Published	09/01/2023 5:40 PM
8175 - Use the attached parameter settings sheet to record the current settings and ...	Remark	Published	09/01/2023 5:46 PM
8221 - 7676 - Brief system operators on expected work, duration, anticipated alarms, and fa...; Remark:	Procedure Step	Published	09/01/2023 9:26 PM
7676 - Brief system operators on expected work, duration, anticipated alarms, and fa...	Instruction	Published	07/01/2023 11:39 PM
8200 - 8176 - Uninstall Faulty Rabbit Board; Remark:	Procedure Step	Published	09/01/2023 8:03 PM
8176 - Uninstall Faulty Rabbit Board	Instruction	Published	09/01/2023 11:19 PM
8201 - 8177 - Loosen screws in each corner and side (6) using medium Phillips screwdriver a...; Remark:8178	Procedure Step	Published	09/01/2023 8:05 PM
7795 - Caution : If you rotate cover of the SCA-775 down without first pulling out from the bo...	Annotation	Published	07/07/2023 2:23 PM
8177 - Loosen screws in each corner and side (6) using medium Phillips screwdriver a...	Instruction	Published	09/01/2023 6:02 PM
8178 - Normally, the cover screws are "captured" and should not come out of cover.	Remark	Published	09/01/2023 6:11 PM
8203 - 8179 - Locate Rabbit board; Remark:8202	Procedure Step	Published	09/01/2023 8:07 PM
8179 - Locate Rabbit board	Instruction	Published	09/01/2023 6:13 PM
8202 - Rabbit board location	Remark	Published	09/01/2023 8:07 PM
8205 - 8180 - Disconnect Ethernet cable from Rabbit board; Remark:8204	Procedure Step	Published	09/01/2023 11:13 PM
7680 - Caution : Make sure to press release button on back of Ethernet cable before removing.	Annotation	Published	07/01/2023 11:54 PM
8180 - Disconnect Ethernet cable from Rabbit board	Instruction	Published	09/01/2023 6:20 PM
8204 - Disconnect Ethernet from Rabbit board	Remark	Published	09/01/2023 8:09 PM
8207 - 8181 - Disconnect wiring harness from SC-771 board for easier access to Rabbit board...; Remark:8206	Procedure Step	Published	09/01/2023 8:13 PM
7798 - Caution : Never remove connectors by pulling on wires.	Annotation	Published	07/07/2023 5:41 PM
7792 - Note : It is good engineering practice to ensure all cables and connectors are label...	Annotation	Published	07/07/2023 2:17 PM
8181 - Disconnect wiring harness from SC-771 board for easier access to Rabbit board...	Instruction	Published	09/01/2023 6:25 PM
8206 - Disconnect Harness	Remark	Published	09/01/2023 8:11 PM
8209 - 8182 - Using small Phillips screwdriver, remove single retaining screw from Rabbit b...; Remark:8208	Procedure Step	Published	09/01/2023 8:14 PM
8182 - Using small Phillips screwdriver, remove single retaining screw from Rabbit b...	Instruction	Published	09/01/2023 6:30 PM
8208 - Unscrew Rabbit board	Remark	Published	09/01/2023 8:14 PM
8211 - 8183 - Remove Rabbit board by gently rocking it back and forth, taking care not to d...; Remark:8210	Procedure Step	Published	09/01/2023 8:17 PM
8183 - Remove Rabbit board by gently rocking it back and forth, taking care not to d...	Instruction	Published	09/01/2023 6:33 PM
8210 - Pull Up Rabbit board	Remark	Published	09/01/2023 8:16 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
8212 - 8184 - Install New Rabbit Board; Remark:	Procedure Step	Published	09/01/2023 8:22 PM
8184 - Install New Rabbit Board	Instruction	Published	09/01/2023 11:19 PM
8213 - 8185 - Mount new Rabbit board; Remark:8186	Procedure Step	Published	09/01/2023 8:24 PM
8185 - Mount new Rabbit board	Instruction	Published	09/01/2023 6:45 PM
8186 - Press on left and right sides of Rabbit board by rocking it back and forth.&n...	Remark	Published	09/01/2023 6:49 PM
8214 - 8187 - Reinstall single retaining screw securing Rabbit board in place; Remark:8208	Procedure Step	Published	09/01/2023 8:27 PM
8187 - Reinstall single retaining screw securing Rabbit board in place	Instruction	Published	09/01/2023 6:51 PM
8215 - 8188 - Reconnect wiring harnesses and Ethernet cable; Remark:7731	Procedure Step	Published	09/01/2023 8:29 PM
7808 - Caution : Proper connection of wiring harnesses is critical.	Annotation	Published	07/07/2023 9:39 PM
8188 - Reconnect wiring harnesses and Ethernet cable	Instruction	Published	09/01/2023 6:54 PM
7731 - Insert Ethernet connector at top of SC-770 module. Connector will audibly "cl...	Remark	Published	07/02/2023 2:36 AM
8216 - 8189 - Close and secure SC-770 module; Remark:8190	Procedure Step	Published	04/13/2025 6:16 PM
8189 - Close and secure SC-770 module	Instruction	Published	04/13/2025 5:57 PM
8190 - Gently tighten 6 screws at the corners and sides on the SC-770 module.	Remark	Published	04/13/2025 5:57 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
8217 - 8193 - Verify Rabbit board firmware is correct; Remark:8194	Procedure Step	Published	09/01/2023 8:39 PM
8191 - Caution : Rabbit board must be configured with correct firmware version before use....	Annotation	Published	09/01/2023 7:11 PM
8192 - Note : If Rabbit board is not pre-configured with correct firmware version, this mus...	Annotation	Published	09/01/2023 7:16 PM
8193 - Verify Rabbit board firmware is correct	Instruction	Published	09/01/2023 7:18 PM
8194 - Enter Program Mode by pressing “0.” Enter the password ...	Remark	Published	09/01/2023 7:23 PM
8218 - 8195 - Verify parameter settings for specific RPM; Remark:8196	Procedure Step	Published	09/01/2023 8:42 PM
8195 - Verify parameter settings for specific RPM	Instruction	Published	09/01/2023 7:27 PM
8196 - Every RPM has unique parameter settings. The currently approved parameter set...	Remark	Published	09/01/2023 7:30 PM
8220 - 8197 - Verify equipment is in normal operating condition; Remark:8219	Procedure Step	Published	09/01/2023 8:45 PM
8197 - Verify equipment is in normal operating condition	Instruction	Published	09/01/2023 7:32 PM
8219 - DET-RPM-RAP-RM03, Operational Testing procedure.	Remark	Published	09/01/2023 8:45 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
Upon failure of Rabbit board	Frequency	Published	09/01/2023 8:57 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Reflective safety vest if required	Replacement Parts	Published	06/20/2023 4:47 PM
safety glasses	Replacement Parts	Published	07/02/2023 4:48 PM
Ladder: 2 meters, 6 feet tall; non-conducting	Replacement Parts	Published	09/01/2023 9:34 PM
Traffic control cones or equivalent if required	Replacement Parts	Published	06/20/2023 4:47 PM
Small Phillips (PH1) screwdriver	Tools	Published	05/14/2020 2:48 PM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
Rabbit Board Location	Image	Published	09/01/2023 6:17 PM
Ethernet Cable Removal from Rabbit Board	Image	Published	09/01/2023 6:21 PM
SC-771 WIring harness	Image	Published	09/01/2023 6:26 PM
Unscrewing Rabbit Board	Image	Published	09/01/2023 6:28 PM
Pull Rabbit Board	Image	Published	09/01/2023 6:31 PM
Push Rabbit Board Down	Image	Published	09/01/2023 6:46 PM
SC-770 Controller Screws	Image	Published	09/01/2023 5:56 PM

Read more about RPM Rabbit Board Replacement

Subscribe to Ladder: 2 meters, 6 feet tall; non-conducting