| 8519 |
8519 - Use a large Phillips (PH3) screwdriver. There should be four (4) screws, but ... |
Remark |
8563 - 8518 - Remove four (4) front panel screws; Remark:8519 |
STEP: 8563 - 8518 - Remove four (4) front panel screws; Remark:8519
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8520 |
8520 - Remove stabilizing brace screws |
Instruction |
8565 - 8520 - Remove stabilizing brace screws; Remark:8521
9602 - 8520 - Remove stabilizing brace screws; Remark:8521 |
STEP: 8565 - 8520 - Remove stabilizing brace screws; Remark:8521
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8521 |
8521 - There should be two stabilizing braces for each He3 tube; configurations migh... |
Remark |
8565 - 8520 - Remove stabilizing brace screws; Remark:8521
9602 - 8520 - Remove stabilizing brace screws; Remark:8521 |
STEP: 8565 - 8520 - Remove stabilizing brace screws; Remark:8521
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8522 |
8522 - Caution : Tube may fall out of detector assembly when bracket screw is removed. |
Annotation |
8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525 |
STEP: 8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8523 |
8523 - Loosen bracket screw (if applicable) |
Instruction |
8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525 |
STEP: 8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8524 |
8524 - Note : This step is only needed if replacing He3 tube from upper detector. |
Annotation |
|
|
✔ |
| 8525 |
8525 - If there is more than one screw, completely remove one. Use medium Phillips (... |
Remark |
8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525 |
STEP: 8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8526 |
8526 - Rotate bracket (if applicable) |
Instruction |
8567 - 8526 - Rotate bracket (if applicable); Remark:8527
8574 - 8526 - Rotate bracket (if applicable); Remark:8536 |
STEP: 8567 - 8526 - Rotate bracket (if applicable); Remark:8527
RPM Neutron Detector Helium-3 (He3) Tube Replacement
STEP: 8574 - 8526 - Rotate bracket (if applicable); Remark:8536
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8527 |
8527 - Rotate neutron bracket |
Remark |
8567 - 8526 - Rotate bracket (if applicable); Remark:8527 |
STEP: 8567 - 8526 - Rotate bracket (if applicable); Remark:8527
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8528 |
8528 - Remove He3 tube |
Instruction |
8568 - 8528 - Remove He3 tube; Remark:8529 |
STEP: 8568 - 8528 - Remove He3 tube; Remark:8529
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8529 |
8529 - Slide tube up through hole and then pull out of moderator. |
Remark |
8568 - 8528 - Remove He3 tube; Remark:8529 |
STEP: 8568 - 8528 - Remove He3 tube; Remark:8529
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8530 |
8530 - Remove stabilizing braces |
Instruction |
8569 - 8530 - Remove stabilizing braces; Remark:8531 |
STEP: 8569 - 8530 - Remove stabilizing braces; Remark:8531
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8531 |
8531 - Slide stabilizing braces off He3 tube. |
Remark |
8569 - 8530 - Remove stabilizing braces; Remark:8531 |
STEP: 8569 - 8530 - Remove stabilizing braces; Remark:8531
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8532 |
8532 - Warning : Do not dispose of He3 neutron tube |
Annotation |
8570 - 5395 - Label faulty component; Remark:7244 |
|
✔ |
| 8533 |
8533 - Install New He3 Tube |
Instruction |
8571 - 8533 - Install New He3 Tube; Remark: |
STEP: 8571 - 8533 - Install New He3 Tube; Remark:
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8534 |
8534 - Place stabilizing braces onto new He3 tube |
Instruction |
8572 - 8534 - Place stabilizing braces onto new He3 tube; Remark: |
STEP: 8572 - 8534 - Place stabilizing braces onto new He3 tube; Remark:
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8535 |
8535 - Insert new He3 tube into moderator |
Instruction |
8573 - 8535 - Insert new He3 tube into moderator; Remark: |
STEP: 8573 - 8535 - Insert new He3 tube into moderator; Remark:
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8536 |
8536 - Rotate He3 tube bracket |
Remark |
8574 - 8526 - Rotate bracket (if applicable); Remark:8536 |
STEP: 8574 - 8526 - Rotate bracket (if applicable); Remark:8536
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8537 |
8537 - Tighten bracket screw (if applicable) |
Instruction |
8575 - 8537 - Tighten bracket screw (if applicable); Remark:8538 |
STEP: 8575 - 8537 - Tighten bracket screw (if applicable); Remark:8538
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8538 |
8538 - Use medium Phillips (PH2) screwdriver. |
Remark |
8575 - 8537 - Tighten bracket screw (if applicable); Remark:8538 |
STEP: 8575 - 8537 - Tighten bracket screw (if applicable); Remark:8538
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8539 |
8539 - Reinstall stabilizing braces screws |
Instruction |
8576 - 8539 - Reinstall stabilizing braces screws; Remark:8540 |
STEP: 8576 - 8539 - Reinstall stabilizing braces screws; Remark:8540
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8540 |
8540 - Use medium Phillips (PH2) screwdriver. |
Remark |
8576 - 8539 - Reinstall stabilizing braces screws; Remark:8540 |
STEP: 8576 - 8539 - Reinstall stabilizing braces screws; Remark:8540
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8541 |
8541 - Reinstall front panel with four (4) screws |
Instruction |
8577 - 8541 - Reinstall front panel with four (4) screws; Remark:8542 |
STEP: 8577 - 8541 - Reinstall front panel with four (4) screws; Remark:8542
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8542 |
8542 - Use large Phillips (PH3) screwdriver. |
Remark |
8577 - 8541 - Reinstall front panel with four (4) screws; Remark:8542 |
STEP: 8577 - 8541 - Reinstall front panel with four (4) screws; Remark:8542
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8543 |
8543 - Reconnect cable to He3 tube |
Instruction |
8578 - 8543 - Reconnect cable to He3 tube; Remark:8544 |
STEP: 8578 - 8543 - Reconnect cable to He3 tube; Remark:8544
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8544 |
8544 - Rotate to align connector notches. Push toward connection and turn coupling n... |
Remark |
8578 - 8543 - Reconnect cable to He3 tube; Remark:8544 |
STEP: 8578 - 8543 - Reconnect cable to He3 tube; Remark:8544
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8545 |
8545 - Isolate new He3 tube |
Instruction |
8579 - 8545 - Isolate new He3 tube; Remark:8547 |
STEP: 8579 - 8545 - Isolate new He3 tube; Remark:8547
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8546 |
8546 - Caution : Do not disconnect cable from new tube |
Annotation |
8579 - 8545 - Isolate new He3 tube; Remark:8547 |
STEP: 8579 - 8545 - Isolate new He3 tube; Remark:8547
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8547 |
8547 - Disconnect cables from all He3 tubes in moderator (white box) except |
Remark |
8579 - 8545 - Isolate new He3 tube; Remark:8547 |
STEP: 8579 - 8545 - Isolate new He3 tube; Remark:8547
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8548 |
8548 - Navigate to SHOW COUNTS for neutron channels |
Instruction |
8580 - 8548 - Navigate to SHOW COUNTS for neutron channels; Remark:8549 |
STEP: 8580 - 8548 - Navigate to SHOW COUNTS for neutron channels; Remark:8549
RPM Neutron Detector Helium-3 (He3) Tube Replacement
RPM HHV-448/458 High Voltage Board Replacement
|
✔ |
| 8549 |
8549 - On SC-770, press 01234# Then, press 2: |
Remark |
8580 - 8548 - Navigate to SHOW COUNTS for neutron channels; Remark:8549 |
STEP: 8580 - 8548 - Navigate to SHOW COUNTS for neutron channels; Remark:8549
RPM Neutron Detector Helium-3 (He3) Tube Replacement
RPM HHV-448/458 High Voltage Board Replacement
|
✔ |
| 8550 |
8550 - Place neutron source on neutron detector |
Instruction |
8581 - 8550 - Place neutron source on neutron detector; Remark:8551 |
STEP: 8581 - 8550 - Place neutron source on neutron detector; Remark:8551
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8551 |
8551 - Secure source to middle of detector with adhesive tape. |
Remark |
8581 - 8550 - Place neutron source on neutron detector; Remark:8551 |
STEP: 8581 - 8550 - Place neutron source on neutron detector; Remark:8551
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8552 |
8552 - Verify counts from new He3 tube |
Instruction |
|
|
✔ |
| 8553 |
8553 - Neutron counts will increase on the channel with the new He3 tube |
Remark |
8582 - 9606 - Verify counts from cleaned He3 tube; Remark:8553 |
STEP: 8582 - 9606 - Verify counts from cleaned He3 tube; Remark:8553
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8554 |
8554 - On SC-770, press # button until main controller screen is di... |
Remark |
8584 - 8458 - Exit programming mode; Remark:8554 |
STEP: 8584 - 8458 - Exit programming mode; Remark:8554
RPM SC-770 Controller Module Replacement
RPM Neutron Detector Helium-3 (He3) Tube Replacement
RPM VD-580 Replacement
RPM SC-770 Rabbit Board Firmware Update
|
✔ |
| 8555 |
8555 - Reconnect all neutron detectors |
Instruction |
8585 - 8555 - Reconnect all neutron detectors; Remark:8556 |
STEP: 8585 - 8555 - Reconnect all neutron detectors; Remark:8556
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8556 |
8556 - Connecting neutron cable |
Remark |
8585 - 8555 - Reconnect all neutron detectors; Remark:8556 |
STEP: 8585 - 8555 - Reconnect all neutron detectors; Remark:8556
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8557 |
8557 - Perform functional compliance test |
Instruction |
8586 - 8557 - Perform functional compliance test; Remark:8558 |
STEP: 8586 - 8557 - Perform functional compliance test; Remark:8558
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8558 |
8558 - DET-RPM-RAP-RM05, RPM Functional Compliance Test. |
Remark |
8586 - 8557 - Perform functional compliance test; Remark:8558 |
STEP: 8586 - 8557 - Perform functional compliance test; Remark:8558
RPM Neutron Detector Helium-3 (He3) Tube Replacement
|
✔ |
| 8559 |
8559 - To reconnect sensor cable, align connectors, push towards sensor, and turn co... |
Remark |
8587 - 7305 - Enable both infrared occupancy sensors; Remark:8559
8588 - 7305 - Enable both infrared occupancy sensors; Remark:8559
8647 - 8661 - Reconnect applicable cable previously removed in Step 4-4; Remark:8559 |
STEP: 8587 - 7305 - Enable both infrared occupancy sensors; Remark:8559
RPM LD-260 Load Disconnect Replacement
RPM Ethernet-to-Fiber Media Converter Replacement
RPM IXIO-DT1 Occupancy Sensor Replacement
RPM SCA-774 Single Channel Analyzer Board Replacement
RPM SCA-775 Module Replacement
RPM LD-260 Load Disconnect Fuse Replacement
RPM SC-771 Controller Board Replacement
RPM SC-770 Controller Module Replacement
RPM Banner IR Occupancy Sensor Replacement
RPM Nano Controller Replacement
RPM SPY-2 to IXIO-DT1 Occupancy Sensor Conversion
RPM Neutron Signal Pick-Off Box (PMFX) Replacement
RPM VD-580 Replacement
STEP: 8588 - 7305 - Enable both infrared occupancy sensors; Remark:8559
RPM Neutron Detector Helium-3 (He3) Tube Replacement
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8560 |
8560 - 8518 - Remove four (4) front panel screws; Remark: |
Procedure Step |
|
|
✔ |
| 8561 |
8561 - 7291 - Disable both infrared occupancy sensors; Remark:8514 |
Procedure Step |
|
|
✔ |
| 8562 |
8562 - 8516 - Disconnect cable from faulty helium-3 (He3) tube; Remark:8517 |
Procedure Step |
|
|
✔ |
| 8563 |
8563 - 8518 - Remove four (4) front panel screws; Remark:8519 |
Procedure Step |
|
|
✔ |
| 8564 |
8564 - 6748 - Remove front panel; Remark: |
Procedure Step |
|
|
✔ |
| 8565 |
8565 - 8520 - Remove stabilizing brace screws; Remark:8521 |
Procedure Step |
|
|
✔ |
| 8566 |
8566 - 8523 - Loosen bracket screw (if applicable); Remark:8525 |
Procedure Step |
|
|
✔ |
| 8567 |
8567 - 8526 - Rotate bracket (if applicable); Remark:8527 |
Procedure Step |
|
|
✔ |
| 8568 |
8568 - 8528 - Remove He3 tube; Remark:8529 |
Procedure Step |
|
|
✔ |
| 8569 |
8569 - 8530 - Remove stabilizing braces; Remark:8531 |
Procedure Step |
|
|
✔ |
| 8571 |
8571 - 8533 - Install New He3 Tube; Remark: |
Procedure Step |
|
|
✔ |
| 8572 |
8572 - 8534 - Place stabilizing braces onto new He3 tube; Remark: |
Procedure Step |
|
|
✔ |
| 8573 |
8573 - 8535 - Insert new He3 tube into moderator; Remark: |
Procedure Step |
|
|
✔ |
| 8574 |
8574 - 8526 - Rotate bracket (if applicable); Remark:8536 |
Procedure Step |
|
|
✔ |
| 8575 |
8575 - 8537 - Tighten bracket screw (if applicable); Remark:8538 |
Procedure Step |
|
|
✔ |
| 8576 |
8576 - 8539 - Reinstall stabilizing braces screws; Remark:8540 |
Procedure Step |
|
|
✔ |
| 8577 |
8577 - 8541 - Reinstall front panel with four (4) screws; Remark:8542 |
Procedure Step |
|
|
✔ |
| 8578 |
8578 - 8543 - Reconnect cable to He3 tube; Remark:8544 |
Procedure Step |
|
|
✔ |
| 8579 |
8579 - 8545 - Isolate new He3 tube; Remark:8547 |
Procedure Step |
|
|
✔ |
| 8580 |
8580 - 8548 - Navigate to SHOW COUNTS for neutron channels; Remark:8549 |
Procedure Step |
|
|
✔ |
| 8581 |
8581 - 8550 - Place neutron source on neutron detector; Remark:8551 |
Procedure Step |
|
|
✔ |
| 8582 |
8582 - 9606 - Verify counts from cleaned He3 tube; Remark:8553 |
Procedure Step |
|
|
✔ |
| 8583 |
8583 - 2581 - Remove radioactive source; Remark: |
Procedure Step |
|
|
✔ |
| 8584 |
8584 - 8458 - Exit programming mode; Remark:8554 |
Procedure Step |
|
|
✔ |
| 8585 |
8585 - 8555 - Reconnect all neutron detectors; Remark:8556 |
Procedure Step |
|
|
✔ |
| 8586 |
8586 - 8557 - Perform functional compliance test; Remark:8558 |
Procedure Step |
|
|
✔ |
| 8587 |
8587 - 7305 - Enable both infrared occupancy sensors; Remark:8559 |
Procedure Step |
|
|
✔ |
| 8588 |
8588 - 7305 - Enable both infrared occupancy sensors; Remark:8559 |
Procedure Step |
|
|
✔ |
| 8589 |
8589 - 7310 - Enable tamper switches; Remark:7348 |
Procedure Step |
|
|
✔ |
| 8591 |
8591 - 8515 - Uninstall Faulty Neutron Tube; Remark: |
Procedure Step |
|
|
✔ |
| 8592 |
8592 - Uninstall faulty RS232 to RS485 converter |
Instruction |
8600 - 8592 - Uninstall faulty RS232 to RS485 converter; Remark: |
STEP: 8600 - 8592 - Uninstall faulty RS232 to RS485 converter; Remark:
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8593 |
8593 - Remove faulty RS232 to RS485 converter |
Instruction |
8605 - 8593 - Remove faulty RS232 to RS485 converter; Remark: |
STEP: 8605 - 8593 - Remove faulty RS232 to RS485 converter; Remark:
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8594 |
8594 - Install new RS232 to RS485 Converter |
Instruction |
8601 - 8594 - Install new RS232 to RS485 Converter; Remark: |
STEP: 8601 - 8594 - Install new RS232 to RS485 Converter; Remark:
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8595 |
8595 - Mount new RS232 to RS485 converter |
Instruction |
8602 - 8595 - Mount new RS232 to RS485 converter; Remark:8596 |
STEP: 8602 - 8595 - Mount new RS232 to RS485 converter; Remark:8596
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8596 |
8596 - Use retained hardware. |
Remark |
8602 - 8595 - Mount new RS232 to RS485 converter; Remark:8596 |
STEP: 8602 - 8595 - Mount new RS232 to RS485 converter; Remark:8596
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8597 |
8597 - Connect power/signal connector and RJ-45 Ethernet cable. |
Remark |
8603 - 2757 - Reconnect wiring; Remark:8597 |
STEP: 8603 - 2757 - Reconnect wiring; Remark:8597
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8598 |
8598 - Reinstall LD-260 (VM-250 only) |
Instruction |
8604 - 8598 - Reinstall LD-260 (VM-250 only); Remark: |
STEP: 8604 - 8598 - Reinstall LD-260 (VM-250 only); Remark:
RPM RS232 to RS485 Converter Replacement
|
✔ |
| 8599 |
8599 - Nano Controller LEDs will illuminate (IN1, IN2 |
Remark |
8606 - 7308 - Verify Nano Controller response; Remark:8599 |
STEP: 8606 - 7308 - Verify Nano Controller response; Remark:8599
RPM RS232 to RS485 Converter Replacement
RPM Nano Controller Replacement
|
✔ |
| 8600 |
8600 - 8592 - Uninstall faulty RS232 to RS485 converter; Remark: |
Procedure Step |
|
|
✔ |
| 8601 |
8601 - 8594 - Install new RS232 to RS485 Converter; Remark: |
Procedure Step |
|
|
✔ |
| 8602 |
8602 - 8595 - Mount new RS232 to RS485 converter; Remark:8596 |
Procedure Step |
|
|
✔ |
| 8603 |
8603 - 2757 - Reconnect wiring; Remark:8597 |
Procedure Step |
|
|
✔ |
| 8604 |
8604 - 8598 - Reinstall LD-260 (VM-250 only); Remark: |
Procedure Step |
|
|
✔ |
| 8605 |
8605 - 8593 - Remove faulty RS232 to RS485 converter; Remark: |
Procedure Step |
|
|
✔ |
| 8606 |
8606 - 7308 - Verify Nano Controller response; Remark:8599 |
Procedure Step |
|
|
✔ |
| 8613 |
8613 - Uninstall Faulty Sensor |
Instruction |
8623 - 8613 - Uninstall Faulty Sensor; Remark: |
STEP: 8623 - 8613 - Uninstall Faulty Sensor; Remark:
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8614 |
8614 - Locate infrared sensors |
Instruction |
8624 - 8614 - Locate infrared sensors; Remark:8615 |
STEP: 8624 - 8614 - Locate infrared sensors; Remark:8615
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8615 |
8615 - Typical sensor locations are as follows: Control pillar hou... |
Remark |
8624 - 8614 - Locate infrared sensors; Remark:8615 |
STEP: 8624 - 8614 - Locate infrared sensors; Remark:8615
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8616 |
8616 - Note : It is unlikely for an emitter and receiver to fail at the same time. Most lik... |
Annotation |
|
|
✔ |
| 8617 |
8617 - Disconnect applicable infrared sensors |
Instruction |
8625 - 8617 - Disconnect applicable infrared sensors; Remark:8618 |
STEP: 8625 - 8617 - Disconnect applicable infrared sensors; Remark:8618
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8618 |
8618 - To disconnect sensor cable, turn collar counterclockwise and pull away from s... |
Remark |
8625 - 8617 - Disconnect applicable infrared sensors; Remark:8618 |
STEP: 8625 - 8617 - Disconnect applicable infrared sensors; Remark:8618
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8619 |
8619 - Unscrew mounting nut |
Instruction |
8626 - 8619 - Unscrew mounting nut; Remark:8620 |
STEP: 8626 - 8619 - Unscrew mounting nut; Remark:8620
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8620 |
8620 - Rotate threaded nut counterclockwise. It may be necessary to hold the infrare... |
Remark |
8626 - 8619 - Unscrew mounting nut; Remark:8620 |
STEP: 8626 - 8619 - Unscrew mounting nut; Remark:8620
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8621 |
8621 - Remove sensor from back of door |
Instruction |
8627 - 8621 - Remove sensor from back of door; Remark:8622 |
STEP: 8627 - 8621 - Remove sensor from back of door; Remark:8622
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8622 |
8622 - Removal of infrared sensor |
Remark |
8627 - 8621 - Remove sensor from back of door; Remark:8622 |
STEP: 8627 - 8621 - Remove sensor from back of door; Remark:8622
RPM Banner IR Occupancy Sensor Replacement
|
✔ |
| 8623 |
8623 - 8613 - Uninstall Faulty Sensor; Remark: |
Procedure Step |
|
|
✔ |
| 8624 |
8624 - 8614 - Locate infrared sensors; Remark:8615 |
Procedure Step |
|
|
✔ |
| 8625 |
8625 - 8617 - Disconnect applicable infrared sensors; Remark:8618 |
Procedure Step |
|
|
✔ |
| 8626 |
8626 - 8619 - Unscrew mounting nut; Remark:8620 |
Procedure Step |
|
|
✔ |
