| 5315 |
5315 - Use medium Phillips (PH2) screwdriver. Retain screws. |
Remark |
5317 - 5316 - Remove four (4) gamma detector screws; Remark:5315 |
STEP: 5317 - 5316 - Remove four (4) gamma detector screws; Remark:5315
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5316 |
5316 - Remove four (4) gamma detector screws |
Instruction |
5317 - 5316 - Remove four (4) gamma detector screws; Remark:5315 |
STEP: 5317 - 5316 - Remove four (4) gamma detector screws; Remark:5315
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5317 |
5317 - 5316 - Remove four (4) gamma detector screws; Remark:5315 |
Procedure Step |
|
|
✔ |
| 5318 |
5318 - Remove three (3) MCA screws |
Instruction |
5319 - 5318 - Remove three (3) MCA screws; Remark:5296 |
STEP: 5319 - 5318 - Remove three (3) MCA screws; Remark:5296
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5319 |
5319 - 5318 - Remove three (3) MCA screws; Remark:5296 |
Procedure Step |
|
|
✔ |
| 5327 |
5327 - IO RadSeeker Circuit Board Beeper Connection |
Remark |
5292 - 5290 - Disconnect beeper; Remark:5289 |
STEP: 5292 - 5290 - Disconnect beeper; Remark:5289
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5328 |
5328 - IO RadSeeker Remove Beeper Cable |
Remark |
5292 - 5290 - Disconnect beeper; Remark:5289 |
STEP: 5292 - 5290 - Disconnect beeper; Remark:5289
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5329 |
5329 - IO RadSeeker Remove Wifi Connector |
Remark |
5295 - 5294 - Disconnect Wi-Fi antenna; Remark:5289 |
STEP: 5295 - 5294 - Disconnect Wi-Fi antenna; Remark:5289
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5330 |
5330 - IO RadSeeker Circuit Board Processor Screws |
Remark |
5298 - 5297 - Remove four (4) processor PCB screws; Remark:5296 |
STEP: 5298 - 5297 - Remove four (4) processor PCB screws; Remark:5296
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5331 |
5331 - IO RadSeeker Lift Processor PCB |
Remark |
5304 - 5302 - Lift processor PCB; Remark:5331 |
STEP: 5304 - 5302 - Lift processor PCB; Remark:5331
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5332 |
5332 - Pull connectors directly away from circuit board. Set aside processor PCB. |
Remark |
5307 - 5306 - Disconnect five (5) processor PCB cables; Remark:5305 |
STEP: 5307 - 5306 - Disconnect five (5) processor PCB cables; Remark:5305
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5333 |
5333 - IO RadSeeker Gamma Detector Three MCA Screws |
Remark |
5319 - 5318 - Remove three (3) MCA screws; Remark:5296 |
STEP: 5319 - 5318 - Remove three (3) MCA screws; Remark:5296
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5334 |
5334 - Carefully pry grommet off of mounting post. |
Remark |
|
|
✔ |
| 5335 |
5335 - Remove mounting bracket tab |
Instruction |
|
|
✔ |
| 5336 |
5336 - Simultaneously lift the MCA and gamma detector and set aside. |
Remark |
5341 - 5337 - Remove gamma detector assembly; Remark:5336 |
STEP: 5341 - 5337 - Remove gamma detector assembly; Remark:5336
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5337 |
5337 - Remove gamma detector assembly |
Instruction |
5341 - 5337 - Remove gamma detector assembly; Remark:5336
5391 - 5337 - Remove gamma detector assembly; Remark:5390 |
STEP: 5341 - 5337 - Remove gamma detector assembly; Remark:5336
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5338 |
5338 - Carefully pry grommet off of mounting post. |
Remark |
5340 - 5339 - Remove mounting bracket tab; Remark:5338 |
STEP: 5340 - 5339 - Remove mounting bracket tab; Remark:5338
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5339 |
5339 - Remove mounting bracket tab |
Instruction |
5340 - 5339 - Remove mounting bracket tab; Remark:5338 |
STEP: 5340 - 5339 - Remove mounting bracket tab; Remark:5338
RadSeeker Check Connections
RadSeeker Stabilization Module Replacement
|
✔ |
| 5340 |
5340 - 5339 - Remove mounting bracket tab; Remark:5338 |
Procedure Step |
|
|
✔ |
| 5341 |
5341 - 5337 - Remove gamma detector assembly; Remark:5336 |
Procedure Step |
|
|
✔ |
| 5342 |
5342 - Attach HATS assessment file to Corrective Maintenance Report. |
Remark |
5344 - 5343 - Attach HATS file; Remark:5342 |
|
✔ |
| 5343 |
5343 - Attach HATS file |
Instruction |
5344 - 5343 - Attach HATS file; Remark:5342 |
|
✔ |
| 5344 |
5344 - 5343 - Attach HATS file; Remark:5342 |
Procedure Step |
|
|
✔ |
| 5345 |
5345 - Perform Setup |
Instruction |
5346 - 5345 - Perform Setup; Remark: |
STEP: 5346 - 5345 - Perform Setup; Remark:
RadSeeker Stabilization Module Replacement
|
✔ |
| 5346 |
5346 - 5345 - Perform Setup; Remark: |
Procedure Step |
|
|
✔ |
| 5347 |
5347 - Reinstall Gamma Detector Assembly |
Instruction |
5348 - 5347 - Reinstall Gamma Detector Assembly; Remark: |
STEP: 5348 - 5347 - Reinstall Gamma Detector Assembly; Remark:
RadSeeker Stabilization Module Replacement
|
✔ |
| 5348 |
5348 - 5347 - Reinstall Gamma Detector Assembly; Remark: |
Procedure Step |
|
|
✔ |
| 5349 |
5349 - Install New Stabilization Module |
Instruction |
5350 - 5349 - Install New Stabilization Module; Remark: |
STEP: 5350 - 5349 - Install New Stabilization Module; Remark:
RadSeeker Stabilization Module Replacement
VeriFinder Stabilization Module Replacement
|
✔ |
| 5350 |
5350 - 5349 - Install New Stabilization Module; Remark: |
Procedure Step |
|
|
✔ |
| 5351 |
5351 - Uninstall Expired Stabilization Module |
Instruction |
5352 - 5351 - Uninstall Expired Stabilization Module; Remark: |
STEP: 5352 - 5351 - Uninstall Expired Stabilization Module; Remark:
RadSeeker Stabilization Module Replacement
|
✔ |
| 5352 |
5352 - 5351 - Uninstall Expired Stabilization Module; Remark: |
Procedure Step |
|
|
✔ |
| 5353 |
5353 - Disassemble Gamma Detector Assembly |
Instruction |
5354 - 5353 - Disassemble Gamma Detector Assembly; Remark: |
STEP: 5354 - 5353 - Disassemble Gamma Detector Assembly; Remark:
RadSeeker Stabilization Module Replacement
|
✔ |
| 5354 |
5354 - 5353 - Disassemble Gamma Detector Assembly; Remark: |
Procedure Step |
|
|
✔ |
| 5355 |
5355 - Backup RadSeeker Files |
Instruction |
5356 - 5355 - Backup RadSeeker Files; Remark: |
STEP: 5356 - 5355 - Backup RadSeeker Files; Remark:
RadSeeker Stabilization Module Replacement
|
✔ |
| 5356 |
5356 - 5355 - Backup RadSeeker Files; Remark: |
Procedure Step |
|
|
✔ |
| 5358 |
5358 - IO RadSeeker PCB Remove Charger |
Remark |
5369 - 5359 - Remove charger PCB; Remark:5358 |
STEP: 5369 - 5359 - Remove charger PCB; Remark:5358
RadSeeker Check Connections
|
✔ |
| 5359 |
5359 - Remove charger PCB |
Instruction |
5369 - 5359 - Remove charger PCB; Remark:5358 |
STEP: 5369 - 5359 - Remove charger PCB; Remark:5358
RadSeeker Check Connections
|
✔ |
| 5360 |
5360 - Use spanner screwdriver with spanner bit (Series 80, Shell size 7). Needle no... |
Remark |
5368 - 5361 - Remove DC cover; Remark:5360
5513 - 5503 - Replace DC cover; Remark:5360 |
STEP: 5368 - 5361 - Remove DC cover; Remark:5360
RadSeeker Check Connections
STEP: 5513 - 5503 - Replace DC cover; Remark:5360
RadSeeker Check Connections
|
✔ |
| 5361 |
5361 - Remove DC cover |
Instruction |
5368 - 5361 - Remove DC cover; Remark:5360 |
STEP: 5368 - 5361 - Remove DC cover; Remark:5360
RadSeeker Check Connections
|
✔ |
| 5362 |
5362 - Use small Phillips (PH1) screwdriver. Retain screws and washers. |
Remark |
5367 - 5363 - Remove four (4) screws; Remark:5362 |
STEP: 5367 - 5363 - Remove four (4) screws; Remark:5362
RadSeeker Check Connections
|
✔ |
| 5363 |
5363 - Remove four (4) screws |
Instruction |
5367 - 5363 - Remove four (4) screws; Remark:5362 |
STEP: 5367 - 5363 - Remove four (4) screws; Remark:5362
RadSeeker Check Connections
|
✔ |
| 5364 |
5364 - Pull connector directly away from circuit board. |
Remark |
5366 - 5365 - Disconnect charger PCB cable; Remark:5364 |
STEP: 5366 - 5365 - Disconnect charger PCB cable; Remark:5364
RadSeeker Check Connections
|
✔ |
| 5365 |
5365 - Disconnect charger PCB cable |
Instruction |
5366 - 5365 - Disconnect charger PCB cable; Remark:5364 |
STEP: 5366 - 5365 - Disconnect charger PCB cable; Remark:5364
RadSeeker Check Connections
|
✔ |
| 5366 |
5366 - 5365 - Disconnect charger PCB cable; Remark:5364 |
Procedure Step |
|
|
✔ |
| 5367 |
5367 - 5363 - Remove four (4) screws; Remark:5362 |
Procedure Step |
|
|
✔ |
| 5368 |
5368 - 5361 - Remove DC cover; Remark:5360 |
Procedure Step |
|
|
✔ |
| 5369 |
5369 - 5359 - Remove charger PCB; Remark:5358 |
Procedure Step |
|
|
✔ |
| 5370 |
5370 - Navigate to Device Utilities page. Select Files tab. Click o... |
Remark |
|
|
✔ |
| 5371 |
5371 - Backup file structure |
Instruction |
5373 - 5371 - Backup file structure; Remark:10751 |
STEP: 5373 - 5371 - Backup file structure; Remark:10751
RadSeeker Stabilization Module Replacement
|
✔ |
| 5372 |
5372 - 220 - Power on instrument; Remark:2303 |
Procedure Step |
|
|
✔ |
| 5373 |
5373 - 5371 - Backup file structure; Remark:10751 |
Procedure Step |
|
|
✔ |
| 5374 |
5374 - IO RadSeeker GPS PCB Two Spacers |
Remark |
5383 - 5313 - Remove two (2) spacers; Remark:5312 |
STEP: 5383 - 5313 - Remove two (2) spacers; Remark:5312
RadSeeker Check Connections
|
✔ |
| 5375 |
5375 - IO RadSeeker GPS PCB Remove |
Remark |
5382 - 5376 - Remove GPS PCB; Remark:5375 |
STEP: 5382 - 5376 - Remove GPS PCB; Remark:5375
RadSeeker Check Connections
|
✔ |
| 5376 |
5376 - Remove GPS PCB |
Instruction |
5382 - 5376 - Remove GPS PCB; Remark:5375 |
STEP: 5382 - 5376 - Remove GPS PCB; Remark:5375
RadSeeker Check Connections
|
✔ |
| 5377 |
5377 - IO RadSeeker GPS Two Mounting Screws |
Remark |
5381 - 5309 - Remove two (2) screws; Remark:5296 |
STEP: 5381 - 5309 - Remove two (2) screws; Remark:5296
RadSeeker Check Connections
|
✔ |
| 5378 |
5378 - IO RadSeeker GPS Remove Connector Away |
Remark |
5380 - 5379 - Disconnect GPS antenna; Remark:5289 |
STEP: 5380 - 5379 - Disconnect GPS antenna; Remark:5289
RadSeeker Check Connections
|
✔ |
| 5379 |
5379 - Disconnect GPS antenna |
Instruction |
5380 - 5379 - Disconnect GPS antenna; Remark:5289 |
STEP: 5380 - 5379 - Disconnect GPS antenna; Remark:5289
RadSeeker Check Connections
|
✔ |
| 5380 |
5380 - 5379 - Disconnect GPS antenna; Remark:5289 |
Procedure Step |
|
|
✔ |
| 5381 |
5381 - 5309 - Remove two (2) screws; Remark:5296 |
Procedure Step |
|
|
✔ |
| 5382 |
5382 - 5376 - Remove GPS PCB; Remark:5375 |
Procedure Step |
|
|
✔ |
| 5383 |
5383 - 5313 - Remove two (2) spacers; Remark:5312 |
Procedure Step |
|
|
✔ |
| 5384 |
5384 - IO RadSeeker Remove SOM Two Spacers |
Remark |
5314 - 5313 - Remove two (2) spacers; Remark:5312 |
STEP: 5314 - 5313 - Remove two (2) spacers; Remark:5312
RadSeeker Check Connections
|
✔ |
| 5385 |
5385 - The stabilization module will be on the top. |
Remark |
5394 - 5386 - Orient gamma detector; Remark:5385 |
STEP: 5394 - 5386 - Orient gamma detector; Remark:5385
RadSeeker Stabilization Module Replacement
|
✔ |
| 5386 |
5386 - Orient gamma detector |
Instruction |
5394 - 5386 - Orient gamma detector; Remark:5385 |
STEP: 5394 - 5386 - Orient gamma detector; Remark:5385
RadSeeker Stabilization Module Replacement
|
✔ |
| 5387 |
5387 - Remove Styrofoam covers |
Instruction |
5393 - 5387 - Remove Styrofoam covers; Remark:5519
6161 - 5387 - Remove Styrofoam covers; Remark:6157 |
STEP: 5393 - 5387 - Remove Styrofoam covers; Remark:5519
RadSeeker Stabilization Module Replacement
STEP: 6161 - 5387 - Remove Styrofoam covers; Remark:6157
VeriFinder Stabilization Module Replacement
|
✔ |
| 5388 |
5388 - Use a wire cutter. |
Remark |
5392 - 5389 - Cut cable ties holding Styrofoam casing; Remark:5388 |
|
✔ |
| 5389 |
5389 - Cut cable ties holding Styrofoam casing |
Instruction |
5392 - 5389 - Cut cable ties holding Styrofoam casing; Remark:5388 |
|
✔ |
| 5390 |
5390 - Refer to DET-HHD-SMD-CM01, RadSeeker Check Connections for detailed ... |
Remark |
5391 - 5337 - Remove gamma detector assembly; Remark:5390 |
|
✔ |
| 5391 |
5391 - 5337 - Remove gamma detector assembly; Remark:5390 |
Procedure Step |
|
|
✔ |
| 5392 |
5392 - 5389 - Cut cable ties holding Styrofoam casing; Remark:5388 |
Procedure Step |
|
|
✔ |
| 5393 |
5393 - 5387 - Remove Styrofoam covers; Remark:5519 |
Procedure Step |
|
|
✔ |
| 5394 |
5394 - 5386 - Orient gamma detector; Remark:5385 |
Procedure Step |
|
|
✔ |
| 5396 |
5396 - Disconnect the MCA [multi-channel analyzer] cable connector from the stabiliz... |
Instruction |
5400 - 5396 - Disconnect the MCA [multi-channel analyzer] cable connector from the stabiliz...; Remark:5531 |
STEP: 5400 - 5396 - Disconnect the MCA [multi-channel analyzer] cable connector from the stabiliz...; Remark:5531
RadSeeker Stabilization Module Replacement
|
✔ |
| 5397 |
5397 - Warning : Do not disassemble the stabilization source module. The expired stabilization... |
Annotation |
5400 - 5396 - Disconnect the MCA [multi-channel analyzer] cable connector from the stabiliz...; Remark:5531 |
STEP: 5400 - 5396 - Disconnect the MCA [multi-channel analyzer] cable connector from the stabiliz...; Remark:5531
RadSeeker Stabilization Module Replacement
|
✔ |
| 5398 |
5398 - Use T6 Torx screwdriver. Retain screws. |
Remark |
5399 - 5405 - Remove two (2) mounting screws; Remark:5398 |
STEP: 5399 - 5405 - Remove two (2) mounting screws; Remark:5398
RadSeeker Stabilization Module Replacement
|
✔ |
| 5399 |
5399 - 5405 - Remove two (2) mounting screws; Remark:5398 |
Procedure Step |
|
|
✔ |
| 5400 |
5400 - 5396 - Disconnect the MCA [multi-channel analyzer] cable connector from the stabiliz...; Remark:5531 |
Procedure Step |
|
|
✔ |
| 5401 |
5401 - Inspect neutron tube for damage. |
Remark |
5423 - 5402 - Remove neutron detector from handle; Remark:5401 |
STEP: 5423 - 5402 - Remove neutron detector from handle; Remark:5401
RadSeeker Check Connections
|
✔ |
| 5402 |
5402 - Remove neutron detector from handle |
Instruction |
5423 - 5402 - Remove neutron detector from handle; Remark:5401 |
STEP: 5423 - 5402 - Remove neutron detector from handle; Remark:5401
RadSeeker Check Connections
|
✔ |
| 5403 |
5403 - Caution : Do not remove moderator unless it will be replaced. |
Annotation |
5423 - 5402 - Remove neutron detector from handle; Remark:5401 |
STEP: 5423 - 5402 - Remove neutron detector from handle; Remark:5401
RadSeeker Check Connections
|
✔ |
| 5404 |
5404 - Use small Phillips (PH1) screwdriver. |
Remark |
5422 - 5405 - Remove two (2) mounting screws; Remark:5404
5457 - 5453 - Replace two (2) mounting screws; Remark:5404
5459 - 5449 - Replace two (2) external handle screws; Remark:5404
5501 - 5494 - Replace two (2) GPS module mounting screws.; Remark:5404
5512 - 5506 - Replace four (4) charger PCB mounting screws; Remark:5404 |
STEP: 5422 - 5405 - Remove two (2) mounting screws; Remark:5404
RadSeeker Check Connections
STEP: 5457 - 5453 - Replace two (2) mounting screws; Remark:5404
RadSeeker Check Connections
STEP: 5459 - 5449 - Replace two (2) external handle screws; Remark:5404
RadSeeker Check Connections
STEP: 5501 - 5494 - Replace two (2) GPS module mounting screws.; Remark:5404
RadSeeker Check Connections
STEP: 5512 - 5506 - Replace four (4) charger PCB mounting screws; Remark:5404
RadSeeker Check Connections
|
✔ |
| 5405 |
5405 - Remove two (2) mounting screws |
Instruction |
5399 - 5405 - Remove two (2) mounting screws; Remark:5398
5422 - 5405 - Remove two (2) mounting screws; Remark:5404
7378 - 5405 - Remove two (2) mounting screws; Remark:7360 |
STEP: 5399 - 5405 - Remove two (2) mounting screws; Remark:5398
RadSeeker Stabilization Module Replacement
STEP: 5422 - 5405 - Remove two (2) mounting screws; Remark:5404
RadSeeker Check Connections
STEP: 7378 - 5405 - Remove two (2) mounting screws; Remark:7360
RPM Ethernet-to-Fiber Media Converter Replacement
|
✔ |
| 5406 |
5406 - Pull directly away from enclosure to loosen handle. |
Remark |
5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406 |
STEP: 5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406
RadSeeker Check Connections
|
✔ |
| 5407 |
5407 - Remove RadSeeker handle/neutron detector |
Instruction |
5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406 |
STEP: 5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406
RadSeeker Check Connections
|
✔ |
| 5408 |
5408 - Caution : The neutron detector electronics are connected to the handle. Remove neutron ... |
Annotation |
5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406 |
STEP: 5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406
RadSeeker Check Connections
|
✔ |
| 5409 |
5409 - IO RadSeeker External Handle Screws |
Remark |
5420 - 5410 - Remove two (2) external handle screws; Remark:5296 |
STEP: 5420 - 5410 - Remove two (2) external handle screws; Remark:5296
RadSeeker Check Connections
|
✔ |
| 5410 |
5410 - Remove two (2) external handle screws |
Instruction |
5420 - 5410 - Remove two (2) external handle screws; Remark:5296 |
STEP: 5420 - 5410 - Remove two (2) external handle screws; Remark:5296
RadSeeker Check Connections
|
✔ |
| 5411 |
5411 - Use small Phillips (PH1) screwdriver. Retain screws, washers and O-rings.... |
Remark |
5419 - 5412 - Remove two (2) internal handle screws; Remark:5411 |
STEP: 5419 - 5412 - Remove two (2) internal handle screws; Remark:5411
RadSeeker Check Connections
|
✔ |
| 5412 |
5412 - Remove two (2) internal handle screws |
Instruction |
5419 - 5412 - Remove two (2) internal handle screws; Remark:5411 |
STEP: 5419 - 5412 - Remove two (2) internal handle screws; Remark:5411
RadSeeker Check Connections
|
✔ |
| 5413 |
5413 - Pull out cable tabs, then remove cable. |
Remark |
5418 - 5414 - Disconnect keypad cable; Remark:5413 |
STEP: 5418 - 5414 - Disconnect keypad cable; Remark:5413
RadSeeker Check Connections
|
✔ |
| 5414 |
5414 - Disconnect keypad cable |
Instruction |
5418 - 5414 - Disconnect keypad cable; Remark:5413 |
STEP: 5418 - 5414 - Disconnect keypad cable; Remark:5413
RadSeeker Check Connections
|
✔ |
| 5415 |
5415 - IO RadSeeker Display PCB Remove Connectors |
Remark |
5417 - 5416 - Disconnect display PCB connectors; Remark:5415 |
STEP: 5417 - 5416 - Disconnect display PCB connectors; Remark:5415
RadSeeker Check Connections
|
✔ |
| 5416 |
5416 - Disconnect display PCB connectors |
Instruction |
5417 - 5416 - Disconnect display PCB connectors; Remark:5415 |
STEP: 5417 - 5416 - Disconnect display PCB connectors; Remark:5415
RadSeeker Check Connections
|
✔ |
| 5417 |
5417 - 5416 - Disconnect display PCB connectors; Remark:5415 |
Procedure Step |
|
|
✔ |
| 5418 |
5418 - 5414 - Disconnect keypad cable; Remark:5413 |
Procedure Step |
|
|
✔ |
| 5419 |
5419 - 5412 - Remove two (2) internal handle screws; Remark:5411 |
Procedure Step |
|
|
✔ |
| 5420 |
5420 - 5410 - Remove two (2) external handle screws; Remark:5296 |
Procedure Step |
|
|
✔ |
| 5421 |
5421 - 5407 - Remove RadSeeker handle/neutron detector; Remark:5406 |
Procedure Step |
|
|
✔ |
| 5422 |
5422 - 5405 - Remove two (2) mounting screws; Remark:5404 |
Procedure Step |
|
|
✔ |
| 5423 |
5423 - 5402 - Remove neutron detector from handle; Remark:5401 |
Procedure Step |
|
|
✔ |
