Quarterly | FRONTLINE Maintenance Tool

Quarterly

RPM Operational Test

Last Updated: 04/24/2025 1:44 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan CM-267 Conveyor Monitor	Device	Published	06/27/2024 1:02 PM
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
1402 - 7927 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/30/2022 1:47 PM
7927 - Establish Initial Conditions	Instruction	Published	07/12/2023 12:23 AM
7977 - 7592 - Inform system operators; Remark:7976	Procedure Step	Published	07/24/2023 9:53 AM
7592 - Inform system operators	Instruction	Published	06/29/2023 3:20 PM
7976 - Operators should expect to receive fault and alarm indications during perform...	Remark	Published	07/24/2023 9:53 AM
7983 - 7981 - Inspect for any physical damage or rodent/insect infestation; Remark:	Procedure Step	Published	07/26/2023 2:45 PM
7982 - Note : Document each step and verification on attached checklist	Annotation	Published	07/26/2023 2:45 PM
7981 - Inspect for any physical damage or rodent/insect infestation	Instruction	Published	07/26/2023 2:44 PM
7984 - 7980 - Close lane and set up barriers or establish a safety watch; Remark:7595	Procedure Step	Published	07/26/2023 2:47 PM
7678 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	07/03/2023 10:23 AM
7980 - Close lane and set up barriers or establish a safety watch	Instruction	Published	07/26/2023 2:46 PM
7595 - Use orange safety (traffic control) cones or equivalent per site-specific saf...	Remark	Published	06/29/2023 3:33 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7997 - 7995 - Disable RPM occupancy sensors; Remark:7994	Procedure Step	Published	07/26/2023 3:08 PM
7995 - Disable RPM occupancy sensors	Instruction	Published	07/26/2023 3:07 PM
7994 - “Relays” Parameter in SC-770 controller must be set to “ON.” Audible ...	Remark	Published	07/26/2023 3:07 PM
7993 - 7992 - Test Gamma Radiation Detection; Remark:	Procedure Step	Published	07/26/2023 3:33 PM
7992 - Test Gamma Radiation Detection	Instruction	Published	07/26/2023 3:33 PM
7989 - 7988 - Initiate and maintain occupancy by interrupting beam of occupancy sensor ...; Remark:	Procedure Step	Published	07/26/2023 3:37 PM
7988 - Initiate and maintain occupancy by interrupting beam of occupancy sensor ...	Instruction	Published	07/26/2023 3:34 PM
7990 - 7987 - Hold Cs-137 source, Co-57 source, or both near front of either gamma detector...; Remark:	Procedure Step	Published	07/26/2023 3:38 PM
7987 - Hold Cs-137 source, Co-57 source, or both near front of either gamma detector...	Instruction	Published	07/26/2023 3:38 PM
7991 - 7986 - Verify red strobe and audible indications function; Remark:7985	Procedure Step	Published	07/26/2023 3:38 PM
7986 - Verify red strobe and audible indications function	Instruction	Published	07/26/2023 3:38 PM
7985 - On SC-770 controller On the control pillar door	Remark	Published	07/26/2023 3:39 PM
8006 - 8004 - Remove Cs-137 source, Co-57 source, or both from detector; Remark:	Procedure Step	Published	07/26/2023 3:45 PM
8005 - Note : Move the source at least 10m from the detectors.	Annotation	Published	07/26/2023 3:45 PM
8004 - Remove Cs-137 source, Co-57 source, or both from detector	Instruction	Published	07/26/2023 3:45 PM
8007 - 8003 - Wait at least 30 seconds for background average to stabilize; Remark:	Procedure Step	Published	07/26/2023 3:46 PM
8003 - Wait at least 30 seconds for background average to stabilize	Instruction	Published	07/26/2023 3:46 PM
8008 - 8002 - Initiate a gamma hi background fault by holding Cs-137 source, Co 57 source, ...; Remark:	Procedure Step	Published	07/26/2023 3:47 PM
8002 - Initiate a gamma hi background fault by holding Cs-137 source, Co 57 source, ...	Instruction	Published	07/26/2023 3:47 PM
8009 - 8001 - Verify amber fault LED indication functions; Remark:8000	Procedure Step	Published	07/26/2023 3:49 PM
8001 - Verify amber fault LED indication functions	Instruction	Published	07/26/2023 3:48 PM
8000 - On SC-770 controller On the control pillar door	Remark	Published	04/13/2025 5:56 PM
8010 - 7998 - Remove Cs-137 source, Co-57 source, or both from detector; Remark:	Procedure Step	Published	07/26/2023 3:52 PM
7999 - Note : Move the source at least 10m from the detectors.	Annotation	Published	07/26/2023 3:52 PM
7998 - Remove Cs-137 source, Co-57 source, or both from detector	Instruction	Published	07/26/2023 3:51 PM
8015 - 8014 - Wait at least 30 seconds for background average to stabilize; Remark:	Procedure Step	Published	07/26/2023 3:54 PM
8014 - Wait at least 30 seconds for background average to stabilize	Instruction	Published	07/26/2023 3:54 PM
8016 - 8012 - Disconnect BNC signal cable from any gamma detector to initiate a gamma lo ba...; Remark:8011	Procedure Step	Published	07/26/2023 3:55 PM
8013 - Note : Occupancy sensors must be disabled during testing of fault indications.	Annotation	Published	07/26/2023 3:56 PM
8012 - Disconnect BNC signal cable from any gamma detector to initiate a gamma lo ba...	Instruction	Published	07/26/2023 3:54 PM
8011 - This can be done on the detector itself or at the SCA‐775 box.	Remark	Published	07/26/2023 3:55 PM
8030 - 8001 - Verify amber fault LED indication functions; Remark:7985	Procedure Step	Published	07/26/2023 4:18 PM
8031 - 8003 - Wait at least 30 seconds for background average to stabilize; Remark:	Procedure Step	Published	07/26/2023 4:19 PM
8032 - 8029 - Reconnect BNC signal cable from step 2-10; Remark:	Procedure Step	Published	07/26/2023 4:20 PM
8029 - Reconnect BNC signal cable from step 2-10	Instruction	Published	07/26/2023 4:19 PM
8028 - 8027 - Test Neutron Radiation Detection; Remark:	Procedure Step	Published	07/26/2023 4:21 PM
8027 - Test Neutron Radiation Detection	Instruction	Published	07/26/2023 4:21 PM
8022 - 7988 - Initiate and maintain occupancy by interrupting beam of occupancy sensor ...; Remark:	Procedure Step	Published	07/26/2023 4:22 PM
8021 - Note : Because CF-252 sources also emit gamma radiation, a gamma alarm may also occu...	Annotation	Published	07/26/2023 4:22 PM
8023 - 8020 - Hold Cf-252 source near front of neutron detector; Remark:	Procedure Step	Published	07/26/2023 4:23 PM
8020 - Hold Cf-252 source near front of neutron detector	Instruction	Published	07/26/2023 4:23 PM
8024 - 8019 - Verify blue strobe and audible indication functions; Remark:7985	Procedure Step	Published	07/26/2023 4:27 PM
8019 - Verify blue strobe and audible indication functions	Instruction	Published	07/26/2023 4:24 PM
8025 - 8018 - Remove Cf-252 source from detector; Remark:	Procedure Step	Published	07/26/2023 4:29 PM
8018 - Remove Cf-252 source from detector	Instruction	Published	07/26/2023 4:28 PM
8026 - 8017 - Wait at least 2 minutes for background average to stabilize; Remark:	Procedure Step	Published	07/26/2023 4:30 PM
8017 - Wait at least 2 minutes for background average to stabilize	Instruction	Published	07/26/2023 4:30 PM
8035 - 8033 - Initiate a neutron hi background fault by holding Cf‐252 source near front ...; Remark:	Procedure Step	Published	07/26/2023 4:32 PM
8034 - Note : A gamma hi fault may also occur during this step. If this is unacceptable, ei...	Annotation	Published	07/26/2023 4:32 PM
8033 - Initiate a neutron hi background fault by holding Cf‐252 source near front ...	Instruction	Published	07/26/2023 4:32 PM
8036 - 8001 - Verify amber fault LED indication functions; Remark:7985	Procedure Step	Published	07/26/2023 4:33 PM
8037 - 8018 - Remove Cf-252 source from detector; Remark:	Procedure Step	Published	07/26/2023 4:34 PM
8044 - 8043 - Test Tamper Fault Circuitry; Remark:	Procedure Step	Published	07/27/2023 8:54 AM
8043 - Test Tamper Fault Circuitry	Instruction	Published	07/27/2023 8:50 AM
8041 - 8040 - Disconnect the AC power supplied to the portal monitor to initiate a “Loss ...; Remark:8039	Procedure Step	Published	07/27/2023 8:57 AM
8040 - Disconnect the AC power supplied to the portal monitor to initiate a “Loss ...	Instruction	Published	07/27/2023 8:55 AM
8039 - 1.If RPM breaker in associated utility panel is marked: Open the RPMs dedicat...	Remark	Published	07/27/2023 8:57 AM
8042 - 8038 - Re-energize RPM, remove magnet from door switch, close cabinet door, and allo...; Remark:	Procedure Step	Published	07/27/2023 8:58 AM
8038 - Re-energize RPM, remove magnet from door switch, close cabinet door, and allo...	Instruction	Published	07/27/2023 8:58 AM
8051 - 8050 - Initiate a cabinet open tamper fault; Remark:	Procedure Step	Published	07/27/2023 9:00 AM
8050 - Initiate a cabinet open tamper fault	Instruction	Published	07/27/2023 9:00 AM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
253 - 242 - Document and report any unresolved problems; Remark:	Procedure Step	Published	06/22/2021 10:23 AM
242 - Document and report any unresolved problems	Instruction	Published	04/21/2025 11:45 AM
Routine Maintenance Procedure	Document Type	Published	03/02/2020 3:31 PM
10 minutes	Duration	Published	04/01/2020 11:35 AM
Quarterly	Frequency	Published	08/02/2020 10:39 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Reflective safety vest if required	Replacement Parts	Published	06/20/2023 4:47 PM
Traffic control cones or equivalent if required	Replacement Parts	Published	06/20/2023 4:47 PM
Magnet	Replacement Parts	Published	07/24/2023 9:53 AM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM

Read more about RPM Operational Test

RPM Cleaning and Inspection

Last Updated: 04/24/2025 1:44 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
1402 - 7927 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/30/2022 1:47 PM
7927 - Establish Initial Conditions	Instruction	Published	07/12/2023 12:23 AM
7579 - 7577 - Brief operators on expected work, duration, anticipated fault indicators, and...; Remark:7576	Procedure Step	Published	06/20/2023 4:37 PM
7577 - Brief operators on expected work, duration, anticipated fault indicators, and...	Instruction	Published	06/20/2023 4:37 PM
7576 - Alarms/faults: Operators should expect to receive tamper (TT) fault indicatio...	Remark	Published	06/20/2023 4:37 PM
7574 - 7572 - Close lane and set up barriers.; Remark:7571	Procedure Step	Published	06/20/2023 4:42 PM
7578 - Warning : Vehicle, and/or pedestrian traffic should temporarily be rerouted or halted d...	Annotation	Published	06/20/2023 4:37 PM
7572 - Close lane and set up barriers.	Instruction	Published	06/20/2023 4:39 PM
7571 - Use orange safety cones or equivalent based on site-specific safety practices...	Remark	Published	06/20/2023 4:42 PM
7588 - 7587 - Clean and inspect RPM cabinet exterior; Remark:	Procedure Step	Published	06/21/2023 9:49 AM
7573 - Note : Perform and document each step in this procedure on a Rapiscan RPM Cleaning a...	Annotation	Published	06/20/2023 4:42 PM
7575 - Reminder : All discrepancies noted during the performance of this procedure should be co...	Annotation	Published	06/20/2023 4:44 PM
7587 - Clean and inspect RPM cabinet exterior	Instruction	Published	06/21/2023 9:48 AM
7585 - 7583 - Inspect exterior for dents, scratches, rust, and bare metal; Remark:	Procedure Step	Published	06/21/2023 9:50 AM
7583 - Inspect exterior for dents, scratches, rust, and bare metal	Instruction	Published	06/21/2023 9:49 AM
7586 - 7582 - Lubricate hinges and keyholes; Remark:7581	Procedure Step	Published	06/21/2023 9:51 AM
7584 - Note : If rust or bare metal is found, take corrective action. See SLD_Technical Ser...	Annotation	Published	06/21/2023 9:50 AM
7582 - Lubricate hinges and keyholes	Instruction	Published	06/21/2023 9:51 AM
7581 - Use of a dry graphite lubricant is recommended.	Remark	Published	06/21/2023 9:51 AM
7903 - 7902 - Inspect RPM and pedestal bolts and flanges; Remark:7901	Procedure Step	Published	07/11/2023 10:57 PM
7902 - Inspect RPM and pedestal bolts and flanges	Instruction	Published	07/11/2023 10:56 PM
7901 - If loose, tighten the bolts and flanges	Remark	Published	07/11/2023 10:57 PM
7900 - 7898 - Clean and inspect RPM cabinet interior; Remark:	Procedure Step	Published	07/11/2023 11:00 PM
7899 - Warning : If standing water is present in the RPM cabinet interior, implement site-spec...	Annotation	Published	07/11/2023 11:00 PM
7898 - Clean and inspect RPM cabinet interior	Instruction	Published	07/11/2023 11:00 PM
7894 - 7893 - Inspect interior of RPM cabinets for dirt, debris, and signs of water; Remark:	Procedure Step	Published	07/11/2023 11:02 PM
7893 - Inspect interior of RPM cabinets for dirt, debris, and signs of water	Instruction	Published	07/11/2023 11:01 PM
7895 - 7892 - Inspect for cables and wires in neat condition and tied down; Remark:	Procedure Step	Published	07/11/2023 11:03 PM
7892 - Inspect for cables and wires in neat condition and tied down	Instruction	Published	07/11/2023 11:02 PM
7896 - 7891 - Inspect desiccant and replace if required; Remark:7890	Procedure Step	Published	07/11/2023 11:03 PM
7891 - Inspect desiccant and replace if required	Instruction	Published	07/11/2023 11:03 PM
7890 - Per DET-RPM-RAP-RM01.	Remark	Published	07/11/2023 11:03 PM
7897 - 7889 - Inspect battery, cables, and connectors for corrosion and damage; Remark:7888	Procedure Step	Published	07/11/2023 11:04 PM
7889 - Inspect battery, cables, and connectors for corrosion and damage	Instruction	Published	07/11/2023 11:04 PM
7888 - Check for swelling of the battery case and corrosion of battery connections; ...	Remark	Published	07/11/2023 11:04 PM
7887 - 7886 - Inspect RPM cabinet for moisture intrusion; Remark:	Procedure Step	Published	07/11/2023 11:06 PM
7886 - Inspect RPM cabinet for moisture intrusion	Instruction	Published	07/11/2023 11:06 PM
7885 - 7884 - Inspect RPM penetrations for integrity and moisture intrusion such as localiz...; Remark:7883	Procedure Step	Published	07/11/2023 11:20 PM
7884 - Inspect RPM penetrations for integrity and moisture intrusion such as localiz...	Instruction	Published	07/11/2023 11:09 PM
7883 - Panel 1 Check that the cabinet penetrations for the lights, speaker, a...	Remark	Published	07/11/2023 11:20 PM
7921 - 7920 - Inspect RPM door seals for leakage; Remark:7919	Procedure Step	Published	07/11/2023 11:23 PM
7920 - Inspect RPM door seals for leakage	Instruction	Published	07/11/2023 11:23 PM
7919 - Localized deposit of dust on the inner side of the RPM door is indicative of ...	Remark	Published	07/11/2023 11:23 PM
7922 - 7918 - Inspect RPM internal surfaces and components for signs of rust and/or mildew; Remark:	Procedure Step	Published	07/11/2023 11:24 PM
7918 - Inspect RPM internal surfaces and components for signs of rust and/or mildew	Instruction	Published	07/11/2023 11:24 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7911 - 7910 - Close doors and lock cabinets; Remark:	Procedure Step	Published	07/11/2023 11:26 PM
7910 - Close doors and lock cabinets	Instruction	Published	07/11/2023 11:26 PM
7912 - 7909 - Dispose of waste materials; Remark:	Procedure Step	Published	07/11/2023 11:27 PM
7909 - Dispose of waste materials	Instruction	Published	07/11/2023 11:27 PM
7913 - 7908 - Verify RPM is communicating with central alarm station and that all faults ar...; Remark:	Procedure Step	Published	07/11/2023 11:27 PM
7908 - Verify RPM is communicating with central alarm station and that all faults ar...	Instruction	Published	07/11/2023 11:27 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Routine Maintenance Procedure	Document Type	Published	03/02/2020 3:31 PM
30 minutes	Duration	Published	04/01/2020 11:35 AM
Quarterly	Frequency	Published	08/02/2020 10:39 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Reminder	Annotation Type	Published	04/08/2020 12:21 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Keys for RPM	Replacement Parts	Published	06/20/2023 4:47 PM
Reflective safety vest if required	Replacement Parts	Published	06/20/2023 4:47 PM
Safety glasses if required	Replacement Parts	Published	06/20/2023 4:47 PM
Ladder if required	Replacement Parts	Published	06/20/2023 4:47 PM
Traffic control cones or equivalent if required	Replacement Parts	Published	06/20/2023 4:47 PM
RPM panel inspect for penetrations or leaking	Image	Published	11/17/2023 8:13 AM

Read more about RPM Cleaning and Inspection

AT6101C Battery Discharge Cycle Android

Last Updated: 04/24/2025 1:37 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Atomtex AT6101C Backpack	Device	Published	06/27/2024 1:47 PM
1660 - 1638 - Drain BT-DU3 adapter battery; Remark:	Procedure Step	Published	11/23/2020 3:00 PM
1638 - Drain BT-DU3 adapter battery	Instruction	Published	11/23/2020 3:27 PM
1661 - 1639 - Start application; Remark:1657	Procedure Step	Published	11/23/2020 3:01 PM
1639 - Start application	Instruction	Published	11/23/2020 2:28 PM
1657 - Radiation Scanner Assistant for Android devices.	Remark	Published	11/23/2020 2:47 PM
1662 - 1640 - Plug Android device into external power; Remark:	Procedure Step	Published	11/23/2020 3:01 PM
1658 - Note : Power loss of Android device due to low battery stops communication with the ...	Annotation	Published	11/23/2020 2:59 PM
1640 - Plug Android device into external power	Instruction	Published	11/23/2020 2:29 PM
1663 - 1641 - Confirm BT-DU3 power is on and communicating with Android device; Remark:1656	Procedure Step	Published	11/23/2020 3:01 PM
1641 - Confirm BT-DU3 power is on and communicating with Android device	Instruction	Published	11/23/2020 2:29 PM
1656 - Connection indicator LEDs of BT-DU3 are flashing.	Remark	Published	11/23/2020 2:46 PM
1664 - 1642 - Allow backpack to operate; Remark:1655	Procedure Step	Published	11/23/2020 3:02 PM
1642 - Allow backpack to operate	Instruction	Published	11/23/2020 2:30 PM
1655 - Approximately 22 hours is required to discharge when starting from a ...	Remark	Published	11/23/2020 2:45 PM
1665 - 1643 - Verify application remains in Idle mode and BT-DU3 is off; Remark:1654	Procedure Step	Published	11/23/2020 3:05 PM
1659 - Note : Battery remaining time and percent charged, displayed in the application Inst...	Annotation	Published	11/23/2020 3:00 PM
1643 - Verify application remains in Idle mode and BT-DU3 is off	Instruction	Published	11/23/2020 3:25 PM
1654 - Discharge is complete and is indicated by the battery low message.	Remark	Published	11/23/2020 3:26 PM
1666 - 1644 - Charge the BT-DU3; Remark:	Procedure Step	Published	11/23/2020 3:07 PM
1644 - Charge the BT-DU3	Instruction	Published	11/23/2020 3:26 PM
1667 - 1645 - Remove BT-DU3 from backpack; Remark:1653	Procedure Step	Published	11/23/2020 3:08 PM
1645 - Remove BT-DU3 from backpack	Instruction	Published	11/23/2020 2:33 PM
1653 - Airflow around the battery aids in temperature control against overheating. D...	Remark	Published	11/23/2020 2:41 PM
1668 - 1646 - Connect battery charger to external power and BT-DU3; Remark:1652	Procedure Step	Published	11/23/2020 2:57 PM
1646 - Connect battery charger to external power and BT-DU3	Instruction	Published	11/23/2020 2:33 PM
1652 - IO AT6101C BTDU3 Plug in Power Connector	Remark	Published	11/23/2020 2:39 PM
1669 - 1647 - Observe red LED; Remark:1651	Procedure Step	Published	11/23/2020 3:08 PM
1647 - Observe red LED	Instruction	Published	11/23/2020 2:34 PM
1651 - Red LED indicates charging is on-going and it will turn off when charging is ...	Remark	Published	11/23/2020 2:38 PM
1670 - 1648 - Confirm a full charge using BT-DU3 adapter battery level indicator; Remark:1650	Procedure Step	Published	11/23/2020 3:09 PM
1648 - Confirm a full charge using BT-DU3 adapter battery level indicator	Instruction	Published	11/23/2020 2:35 PM
1650 - Press and hold PWR button to display the six LEDs indicating a full charge.	Remark	Published	11/23/2020 2:37 PM
253 - 242 - Document and report any unresolved problems; Remark:	Procedure Step	Published	06/22/2021 10:23 AM
242 - Document and report any unresolved problems	Instruction	Published	04/21/2025 11:45 AM
Routine Maintenance Procedure	Document Type	Published	03/02/2020 3:31 PM
25 hours	Duration	Published	08/02/2020 10:38 PM
Quarterly	Frequency	Published	08/02/2020 10:39 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
None	Tools	Published	05/06/2020 9:50 PM
AT6101C_RSA_Icon04.png	Image	Published	09/04/2020 4:11 PM
AT6101C_BTDU3_Communicate_Wireless_red_circle	Image	Published	09/04/2020 10:51 PM
AT6101C_RSA_Idle_Low_Battery_red_box_arrow	Image	Published	03/30/2022 2:22 AM
Atomtex_BT-DU3_Connect_to_power	Image	Published	09/04/2020 10:30 PM
AT6101C_Power_BTDU3_Controller_LED_on_red_circle	Image	Published	09/04/2020 10:52 PM
AT6101C BTDU3 Checking Battery Level Red Arrow	Image	Published	09/04/2020 10:40 PM

Read more about AT6101C Battery Discharge Cycle Android

Subscribe to Quarterly