Side Cutter Pliers | FRONTLINE Maintenance Tool

RPM LED Fault Light Assembly Replacement

Last Updated: 04/25/2025 1:43 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
9418 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	10/03/2023 12:42 PM
9341 - Note : If only replacing the fault LED bulb, twist connector one-quarter turn counte...	Annotation	Published	10/03/2023 10:34 AM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7268 - 7231 - Close lane; Remark:7233	Procedure Step	Published	04/27/2023 7:01 PM
9053 - Warning : Traffic should temporarily be rerouted or halted during conduction of this pr...	Annotation	Published	09/27/2023 9:09 AM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7269 - 7232 - Open RPM door; Remark:7234	Procedure Step	Published	04/27/2023 7:02 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7234 - Open all doors needed to access components.	Remark	Published	04/19/2025 7:48 PM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
9412 - 9350 - Disconnect LED Fault Light Wiring; Remark:	Procedure Step	Published	10/03/2023 12:45 PM
9350 - Disconnect LED Fault Light Wiring	Instruction	Published	10/03/2023 12:21 PM
9406 - 9351 - Open Control door to access terminal block (TB4) on the back of the door ...; Remark:8674	Procedure Step	Published	10/03/2023 12:46 PM
8675 - Note : If repairing a pedestrian monitor, go to Step 2-4	Annotation	Published	09/24/2023 9:59 AM
9351 - Open Control door to access terminal block (TB4) on the back of the door ...	Instruction	Published	10/03/2023 12:21 PM
8674 - For vehicle monitors: Open the upper RPM door	Remark	Published	09/24/2023 9:58 AM
9407 - 9352 - Remove black wire (TB4-3) and black wire (TB4-4) from TB4 using a small flath...; Remark:9530	Procedure Step	Published	10/03/2023 12:46 PM
9352 - Remove black wire (TB4-3) and black wire (TB4-4) from TB4 using a small flath...	Instruction	Published	10/03/2023 12:21 PM
9530 -	Remark	Published	10/04/2023 2:05 PM
9408 - 9353 - Remove any wire ties securing red and black wires using side cutter pliers; Remark:	Procedure Step	Published	10/03/2023 12:46 PM
9353 - Remove any wire ties securing red and black wires using side cutter pliers	Instruction	Published	10/03/2023 12:22 PM
9409 - 9354 - Open Control RPM door to identify wiring connections (for pedestrian monitors...; Remark:9529	Procedure Step	Published	10/03/2023 12:46 PM
9354 - Open Control RPM door to identify wiring connections (for pedestrian monitors...	Instruction	Published	10/03/2023 12:22 PM
9529 -	Remark	Published	10/04/2023 2:06 PM
9410 - 9355 - Remove connectors by cutting wires as close as possible to end of each connec...; Remark:	Procedure Step	Published	10/03/2023 12:46 PM
9355 - Remove connectors by cutting wires as close as possible to end of each connec...	Instruction	Published	10/03/2023 12:22 PM
9411 - 9356 - Remove any wire ties securing wires using side cutter pliers; Remark:	Procedure Step	Published	10/03/2023 12:56 PM
9356 - Remove any wire ties securing wires using side cutter pliers	Instruction	Published	10/03/2023 12:23 PM
9405 - 9357 - Uninstall Fault Light Hardware; Remark:	Procedure Step	Published	10/03/2023 12:47 PM
9357 - Uninstall Fault Light Hardware	Instruction	Published	10/03/2023 12:23 PM
9400 - 9358 - Gently pry fault light cover off; Remark:9528	Procedure Step	Published	10/03/2023 12:47 PM
9358 - Gently pry fault light cover off	Instruction	Published	10/03/2023 12:23 PM
9528 -	Remark	Published	10/04/2023 2:07 PM
9401 - 9359 - Install new fault light housing to front of door; Remark:9343	Procedure Step	Published	10/03/2023 12:48 PM
9359 - Install new fault light housing to front of door	Instruction	Published	10/03/2023 12:23 PM
9343 - Use a medium Phillips screwdriver for the front of the door and a 7 mm nut dr...	Remark	Published	10/03/2023 12:09 PM
9402 - 9360 - Remove fault light back plate by rotating it 45 degrees counterclockwise and ...; Remark:9527	Procedure Step	Published	10/03/2023 12:48 PM
9360 - Remove fault light back plate by rotating it 45 degrees counterclockwise and ...	Instruction	Published	10/03/2023 12:24 PM
9527 -	Remark	Published	10/04/2023 2:12 PM
9403 - 9361 - Pull fault light socket through hole in door; Remark:	Procedure Step	Published	10/03/2023 12:48 PM
9361 - Pull fault light socket through hole in door	Instruction	Published	10/03/2023 12:24 PM
9404 - 9362 - Remove any leftover silicone from hole in door using flathead screwdriver...; Remark:9526	Procedure Step	Published	10/03/2023 12:48 PM
9362 - Remove any leftover silicone from hole in door using flathead screwdriver...	Instruction	Published	10/03/2023 12:24 PM
9526 -	Remark	Published	10/04/2023 2:14 PM
9399 - 9363 - Install New Fault Light Hardware; Remark:	Procedure Step	Published	10/03/2023 12:49 PM
9363 - Install New Fault Light Hardware	Instruction	Published	10/03/2023 12:25 PM
9395 - 9364 - Feed wires of new fault light assembly through hole in door; Remark:	Procedure Step	Published	10/03/2023 12:49 PM
9364 - Feed wires of new fault light assembly through hole in door	Instruction	Published	10/03/2023 12:25 PM
9396 - 9365 - Install new fault light housing to front of door; Remark:9344	Procedure Step	Published	10/03/2023 12:49 PM
569 - Caution : Do not overtighten screws.	Annotation	Published	06/16/2021 2:31 PM
9365 - Install new fault light housing to front of door	Instruction	Published	10/03/2023 12:25 PM
9344 - Use a medium Phillips screwdriver for the front of the door and a 7 mm nut dr...	Remark	Published	10/03/2023 12:10 PM
9397 - 9366 - Apply silicone around the rim of socket on back of door; Remark:9536	Procedure Step	Published	10/03/2023 12:50 PM
8701 - Warning : Use protective gloves when handling silicone.	Annotation	Published	09/24/2023 1:50 PM
9366 - Apply silicone around the rim of socket on back of door	Instruction	Published	10/03/2023 12:26 PM
9536 -	Remark	Published	10/04/2023 2:18 PM
9398 - 9367 - Install new fault light cover to front of door; Remark:	Procedure Step	Published	10/03/2023 12:50 PM
9367 - Install new fault light cover to front of door	Instruction	Published	10/03/2023 12:26 PM
9394 - 9368 - Reconnect LED Fault Light Wiring; Remark:	Procedure Step	Published	10/03/2023 12:51 PM
9368 - Reconnect LED Fault Light Wiring	Instruction	Published	10/03/2023 12:26 PM
9387 - 9369 - Open Control pillar door to access terminal block (TB4) on back of door; Remark:8674	Procedure Step	Published	10/03/2023 12:51 PM
8712 - Note : If repairing a pedestrian monitor, go to Step 5-4	Annotation	Published	09/24/2023 2:12 PM
9369 - Open Control pillar door to access terminal block (TB4) on back of door	Instruction	Published	10/03/2023 12:27 PM
9388 - 9370 - Reinstall black wire (TB4-3) and black wire (TB4-4) wiring into TB4 using a s...; Remark:9535	Procedure Step	Published	10/03/2023 12:51 PM
9370 - Reinstall black wire (TB4-3) and black wire (TB4-4) wiring into TB4 using a s...	Instruction	Published	10/03/2023 12:27 PM
9535 -	Remark	Published	10/04/2023 2:19 PM
9389 - 9371 - Add ties to secure wires where needed; Remark:	Procedure Step	Published	10/03/2023 12:52 PM
9371 - Add ties to secure wires where needed	Instruction	Published	10/03/2023 12:27 PM
9390 - 9372 - Open Control RPM door to access fault light connections (for pedestrian monit...; Remark:9534	Procedure Step	Published	10/03/2023 12:52 PM
9372 - Open Control RPM door to access fault light connections (for pedestrian monit...	Instruction	Published	10/03/2023 12:28 PM
9534 -	Remark	Published	10/04/2023 2:19 PM
9391 - 9373 - Strip 1 cm from end of connecting wires using crimping tool; Remark:9533	Procedure Step	Published	10/03/2023 12:52 PM
9373 - Strip 1 cm from end of connecting wires using crimping tool	Instruction	Published	10/03/2023 12:28 PM
9533 -	Remark	Published	10/04/2023 2:20 PM
9392 - 9374 - Remove sheathing from end of fault light wires using crimping tool; Remark:9532	Procedure Step	Published	10/03/2023 12:52 PM
9374 - Remove sheathing from end of fault light wires using crimping tool	Instruction	Published	10/03/2023 12:28 PM
9532 -	Remark	Published	10/04/2023 2:21 PM
9393 - 9375 - Crimp union connectors to appropriate wires using a crimping tool; Remark:9345	Procedure Step	Published	10/03/2023 12:53 PM
9375 - Crimp union connectors to appropriate wires using a crimping tool	Instruction	Published	10/03/2023 12:29 PM
9345 - Join the related wires back together with union connectors. Connect red and w...	Remark	Published	10/03/2023 12:10 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
10318 - 10316 - Verify fault light turns on; Remark:10317	Procedure Step	Published	11/17/2023 11:42 AM
10316 - Verify fault light turns on	Instruction	Published	11/17/2023 11:39 AM
10317 - Fault light	Remark	Published	11/17/2023 11:41 AM
7281 - 7252 - Verify RPM start-up; Remark:7253	Procedure Step	Published	04/20/2025 3:26 PM
7252 - Verify RPM start-up	Instruction	Published	04/27/2023 2:23 PM
7253 - RPM will perform a power on self-test (POST) and collect a background radiati...	Remark	Published	05/10/2023 3:14 PM
9385 - 319 - Perform operational test; Remark:9347	Procedure Step	Published	10/03/2023 12:54 PM
319 - Perform operational test	Instruction	Published	06/10/2021 8:31 PM
9347 - DET-RPM-RAP-RM03 RPM Operational Testing.	Remark	Published	10/03/2023 12:11 PM
7282 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	04/27/2023 4:15 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
30 minutes	Duration	Published	04/01/2020 11:35 AM
Upon failure of LED fault light	Frequency	Published	10/04/2023 9:16 AM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Small slotted (flathead) screwdriver	Tools	Published	09/11/2020 11:23 AM
Side Cutter Pliers	Tools	Published	10/04/2023 9:15 AM
7 mm socket wrench or nut driver	Tools	Published	10/04/2023 9:16 AM
Wire crimping tool	Tools	Published	09/25/2023 4:20 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Remove black wire (TB4-3) and black wire (TB4-4) from TB4 using a small flathead screwdriver	Image	Published	10/04/2023 1:06 PM
Open Control RPM door to identify wiring connections (for pedestrian monitors)	Image	Published	10/04/2023 1:08 PM
Gently pry fault light cover off	Image	Published	10/04/2023 1:10 PM
Install new fault light housing to front of door	Image	Published	10/04/2023 1:12 PM
Install new fault light housing to front of door pt2	Image	Published	10/04/2023 1:15 PM
Remove fault light back plate	Image	Published	10/04/2023 1:16 PM
Remove any leftover silicone from hole	Image	Published	10/04/2023 1:20 PM
Apply silicone around the rim of socket on back of door	Image	Published	10/04/2023 1:25 PM
Reinstall black wire (TB4-3) and black wire (TB4-4) wiring into TB4 using a small flathead screwdriver	Image	Published	10/04/2023 1:54 PM
Strip 1 cm from end of connecting wires using crimping tool	Image	Published	10/04/2023 1:59 PM
Remove sheathing from end of fault light wires using crimping tool	Image	Published	10/04/2023 2:00 PM
Crimp union connectors to appropriate wires using a crimping tool	Image	Published	10/04/2023 2:02 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
Switch LD-260 to on position while watching new LED fault light	Image	Published	10/04/2023 2:03 PM

Read more about RPM LED Fault Light Assembly Replacement

RPM Alarm Strobe Light Assembly Replacement

Last Updated: 04/25/2025 1:43 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
8489 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/24/2023 9:51 AM
7265 - Warning : Traffic should temporarily be rerouted or halted during this procedure to ens...	Annotation	Published	04/27/2023 1:42 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
8490 - 7592 - Inform system operators; Remark:	Procedure Step	Published	09/16/2023 8:49 PM
7592 - Inform system operators	Instruction	Published	06/29/2023 3:20 PM
8221 - 7676 - Brief system operators on expected work, duration, anticipated alarms, and fa...; Remark:	Procedure Step	Published	09/01/2023 9:26 PM
7676 - Brief system operators on expected work, duration, anticipated alarms, and fa...	Instruction	Published	07/01/2023 11:39 PM
10262 - 7967 - Close lane and set up barriers or establish a safety watch; Remark:7595	Procedure Step	Published	11/10/2023 12:51 PM
7967 - Close lane and set up barriers or establish a safety watch	Instruction	Published	07/12/2023 12:41 AM
7595 - Use orange safety (traffic control) cones or equivalent per site-specific saf...	Remark	Published	06/29/2023 3:33 PM
10264 - 9235 - Open Control pillar RPM door; Remark:	Procedure Step	Published	11/10/2023 12:52 PM
9235 - Open Control pillar RPM door	Instruction	Published	10/03/2023 12:03 PM
10265 - 9236 - Switch LD-260 to OFF position and verify green “PWR ON” LED is not lit; Remark:10263	Procedure Step	Published	11/10/2023 12:56 PM
9236 - Switch LD-260 to OFF position and verify green “PWR ON” LED is not lit	Instruction	Published	10/03/2023 12:01 PM
10263 -	Remark	Published	11/10/2023 12:56 PM
8719 - 8672 - Disconnect Strobe Light Wiring; Remark:	Procedure Step	Published	09/24/2023 3:39 PM
8672 - Disconnect Strobe Light Wiring	Instruction	Published	09/24/2023 9:54 AM
8720 - 8673 - Locate terminal block TB4; Remark:8674	Procedure Step	Published	09/24/2023 4:50 PM
8675 - Note : If repairing a pedestrian monitor, go to Step 2-4	Annotation	Published	09/24/2023 9:59 AM
8673 - Locate terminal block TB4	Instruction	Published	09/24/2023 10:02 AM
8674 - For vehicle monitors: Open the upper RPM door	Remark	Published	09/24/2023 9:58 AM
8721 - 8676 - Disconnect wiring from terminal block TB4; Remark:8677	Procedure Step	Published	09/24/2023 3:41 PM
8676 - Disconnect wiring from terminal block TB4	Instruction	Published	09/24/2023 10:01 AM
8677 - Using a small flathead screwdriver, for the blue neutron strobe, remove wires...	Remark	Published	09/24/2023 10:06 AM
8722 - 8678 - Release wiring harness from fasteners; Remark:8679	Procedure Step	Published	04/13/2025 6:16 PM
8678 - Release wiring harness from fasteners	Instruction	Published	04/13/2025 6:10 PM
8679 - TB4 Wiring Harness Fasteners	Remark	Published	09/24/2023 10:09 AM
8723 - 8680 - Identify strobe light wiring (for pedestrian monitor); Remark:8681	Procedure Step	Published	09/24/2023 3:42 PM
8680 - Identify strobe light wiring (for pedestrian monitor)	Instruction	Published	09/24/2023 10:12 AM
8681 - Blue neutron strobe: Positive terminal (+): Two (2...	Remark	Published	09/24/2023 10:18 AM
8724 - 8678 - Release wiring harness from fasteners; Remark:8682	Procedure Step	Published	04/13/2025 6:16 PM
8682 - Use cutter pliers to remove any fasteners associated wth strobe light wiring....	Remark	Published	09/24/2023 10:23 AM
8725 - 8683 - Disconnect wires from strobe light wiring; Remark:8684	Procedure Step	Published	04/13/2025 6:16 PM
8683 - Disconnect wires from strobe light wiring	Instruction	Published	04/13/2025 6:10 PM
8684 - Remove forked connectors from Sonalert using a small Phillips screwdriver. Us...	Remark	Published	09/24/2023 10:27 AM
8726 - 8685 - Uninstall Red and Blue Strobe Assemblies; Remark:	Procedure Step	Published	04/13/2025 6:16 PM
8685 - Uninstall Red and Blue Strobe Assemblies	Instruction	Published	04/13/2025 6:10 PM
8727 - 8686 - Remove circular black cover from strobe light; Remark:8687	Procedure Step	Published	09/24/2023 3:45 PM
8686 - Remove circular black cover from strobe light	Instruction	Published	09/24/2023 1:05 PM
8687 - Use a small flathead screwdriver to pry the circular black cover off.	Remark	Published	04/13/2025 6:10 PM
8728 - 8688 - Remove strobe light assembly; Remark:8689	Procedure Step	Published	09/24/2023 3:45 PM
8688 - Remove strobe light assembly	Instruction	Published	09/24/2023 1:10 PM
8689 - Use a 3/16" Allen wrench to remove strobe light assembly.	Remark	Published	09/24/2023 1:14 PM
8729 - 8690 - Pry strobe assembly from RPM door; Remark:8691	Procedure Step	Published	09/24/2023 3:46 PM
8690 - Pry strobe assembly from RPM door	Instruction	Published	09/24/2023 1:16 PM
8691 - Use a putty knife to pry strobe assembly off RPM door.	Remark	Published	09/24/2023 1:20 PM
8730 - 8692 - Pull hardware assembly with wires to remove; Remark:	Procedure Step	Published	09/24/2023 3:46 PM
8692 - Pull hardware assembly with wires to remove	Instruction	Published	09/24/2023 1:21 PM
8731 - 8693 - Remove residue off RPM door; Remark:8694	Procedure Step	Published	09/24/2023 3:47 PM
8693 - Remove residue off RPM door	Instruction	Published	09/24/2023 1:22 PM
8694 - Use a putty knife to remove silicone or residue off RPM door.	Remark	Published	09/24/2023 1:25 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
8732 - 8695 - Install and Seal New Red and Blue Strobe Assembly; Remark:	Procedure Step	Published	09/24/2023 3:49 PM
8695 - Install and Seal New Red and Blue Strobe Assembly	Instruction	Published	09/24/2023 1:30 PM
8733 - 8696 - Route strobe light assembly wires; Remark:8697	Procedure Step	Published	09/24/2023 3:50 PM
8696 - Route strobe light assembly wires	Instruction	Published	09/24/2023 1:35 PM
8697 - Insert new strobe light assembly wires through grommet located in RPM door.	Remark	Published	09/24/2023 1:37 PM
8734 - 8699 - Apply silicone to strobe light assembly; Remark:8700	Procedure Step	Published	09/24/2023 3:51 PM
8701 - Warning : Use protective gloves when handling silicone.	Annotation	Published	09/24/2023 1:50 PM
8699 - Apply silicone to strobe light assembly	Instruction	Published	09/24/2023 1:47 PM
8700 - Apply Silicone to Strobe Light	Remark	Published	09/24/2023 1:49 PM
8735 - 8702 - Install new strobe light assembly to front of door; Remark:8703	Procedure Step	Published	09/24/2023 3:52 PM
8702 - Install new strobe light assembly to front of door	Instruction	Published	09/24/2023 1:51 PM
8703 - Align strobe assembly hole to the hole in the front of the RPM door. Then, fi...	Remark	Published	09/24/2023 1:53 PM
8736 - 8704 - Tighten strobe light assembly; Remark:8705	Procedure Step	Published	09/24/2023 3:52 PM
8706 - Caution : Do not overtighten hardware	Annotation	Published	04/05/2025 4:27 PM
8704 - Tighten strobe light assembly	Instruction	Published	09/24/2023 1:59 PM
8705 - Use a 3/16" Allen wrench to tighten clockwise until secure.	Remark	Published	04/13/2025 6:09 PM
8738 - 8707 - Insert circular black cover on strobe light assembly; Remark:8708	Procedure Step	Published	09/24/2023 3:57 PM
8707 - Insert circular black cover on strobe light assembly	Instruction	Published	09/24/2023 2:01 PM
8708 - Strobe Light Circular Black Cover	Remark	Published	09/24/2023 2:03 PM
8737 - 8709 - Remove excess silicone from around strobe light assembly edges; Remark:8710	Procedure Step	Published	09/24/2023 3:54 PM
8709 - Remove excess silicone from around strobe light assembly edges	Instruction	Published	09/24/2023 2:05 PM
8710 - Strobe Light Edges	Remark	Published	09/24/2023 2:06 PM
8739 - 8711 - Reconnect Strobe Light Wiring; Remark:	Procedure Step	Published	09/24/2023 3:58 PM
8711 - Reconnect Strobe Light Wiring	Instruction	Published	09/24/2023 2:11 PM
8740 - 8713 - Reconnect wiring from terminal TB4; Remark:8677	Procedure Step	Published	09/24/2023 3:59 PM
8712 - Note : If repairing a pedestrian monitor, go to Step 5-4	Annotation	Published	09/24/2023 2:12 PM
7263 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	04/24/2023 2:32 PM
8713 - Reconnect wiring from terminal TB4	Instruction	Published	09/24/2023 2:13 PM
8741 - 8714 - Add wire fasteners where removed; Remark:	Procedure Step	Published	09/24/2023 3:59 PM
8714 - Add wire fasteners where removed	Instruction	Published	09/24/2023 2:16 PM
8742 - 8680 - Identify strobe light wiring (for pedestrian monitor); Remark:8681	Procedure Step	Published	09/24/2023 4:00 PM
8743 - 8715 - Crimp forked connectors to end of strobe light wires; Remark:8716	Procedure Step	Published	09/24/2023 4:01 PM
8715 - Crimp forked connectors to end of strobe light wires	Instruction	Published	09/24/2023 2:18 PM
8716 - Remove ¼ inch (6mm) of insulation from the strobe light assembly wire end us...	Remark	Published	09/24/2023 2:19 PM
8744 - 8717 - Connect strobe light assembly wire to Sonalert; Remark:8718	Procedure Step	Published	09/24/2023 4:02 PM
8717 - Connect strobe light assembly wire to Sonalert	Instruction	Published	09/24/2023 2:20 PM
8718 - Using a small Phillips screwdriver, terminate the forked connectors to the co...	Remark	Published	09/24/2023 2:21 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
8503 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	09/16/2023 9:00 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
8506 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	09/24/2023 3:34 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
8258 - 319 - Perform operational test; Remark:8219	Procedure Step	Published	04/08/2025 2:11 PM
319 - Perform operational test	Instruction	Published	06/10/2021 8:31 PM
8219 - DET-RPM-RAP-RM03, Operational Testing procedure.	Remark	Published	09/01/2023 8:45 PM
8507 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/24/2023 3:35 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
Upon failure of alarm indicator	Frequency	Published	09/24/2023 4:35 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Small Phillips (PH1) screwdriver	Tools	Published	05/14/2020 2:48 PM
Small slotted (flathead) screwdriver	Tools	Published	09/11/2020 11:23 AM
Side Cutter Pliers	Tools	Published	10/04/2023 9:15 AM
Putty Knife	Tools	Published	11/10/2023 12:37 PM
Crimping Tool	Tools	Published	11/10/2023 12:38 PM
3/16" Allen Wrench	Tools	Published	09/24/2023 4:34 PM
Switch LD-260 to OFF position and verify green "PWR ON" LED is not lit	Image	Published	10/04/2023 11:08 AM
Neutron and Gamma Stobe Wiring	Image	Published	09/24/2023 10:03 AM
Wiring Harness Fasteners	Image	Published	09/24/2023 10:09 AM
Strobe wiring harness fasteners	Image	Published	09/24/2023 10:22 AM
Disconnect Sonalert Wires	Image	Published	09/24/2023 10:26 AM
Remove black cover from strobe light	Image	Published	09/24/2023 1:08 PM
Strobe Light Assembly Removal	Image	Published	09/24/2023 1:14 PM
Pry Off Strobe Assembly	Image	Published	09/24/2023 1:20 PM
Remove Residue	Image	Published	09/24/2023 1:24 PM
Route strobe light wires	Image	Published	09/24/2023 1:35 PM
App,y SIlicone to Strobe Light Assembly	Image	Published	09/24/2023 1:48 PM
Strobe Light Black Cover	Image	Published	09/24/2023 2:03 PM
Strobe Light Edge	Image	Published	09/24/2023 2:06 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM

Read more about RPM Alarm Strobe Light Assembly Replacement

Subscribe to Side Cutter Pliers