RPM SPY-2 to IXIO-DT1 Occupancy Sensor Conversion

Last Updated: 06/18/2025 1:43 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/05/2025 11:30 AM
7264 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	04/27/2023 7:00 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7622 - 7592 - Inform system operators; Remark:11335	Procedure Step	Published	04/20/2025 10:15 AM
7592 - Inform system operators	Instruction	Published	06/29/2023 3:20 PM
11335 - Upon arrival, brief system operators on expected work, duration, anticipated ...	Remark	Published	04/20/2025 10:14 AM
7452 - 7231 - Close lane; Remark:7415	Procedure Step	Published	06/02/2023 5:12 PM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7415 - Re-route pedestrian traffic.	Remark	Published	06/02/2023 1:08 PM
7269 - 7232 - Open RPM door; Remark:7234	Procedure Step	Published	04/27/2023 7:02 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7234 - Open all doors needed to access components.	Remark	Published	04/19/2025 7:48 PM
7755 - 7679 - Disconnect Ethernet; Remark:11336	Procedure Step	Published	04/20/2025 11:18 AM
7680 - Caution : Make sure to press release button on back of Ethernet cable before removing.	Annotation	Published	07/01/2023 11:54 PM
7679 - Disconnect Ethernet	Instruction	Published	05/16/2025 8:03 PM
11336 - Locate Ethernet connector on top of SC-770 controller. Press release button o...	Remark	Published	04/20/2025 11:21 AM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
7454 - 7290 - Disable tamper switches; Remark:7416	Procedure Step	Published	06/02/2023 5:25 PM
7290 - Disable tamper switches	Instruction	Published	05/01/2023 8:14 AM
7416 - Use a magnet to disable tamper switches for all open doors. Use adhesive tape...	Remark	Published	06/02/2023 1:18 PM
8561 - 7291 - Disable both infrared occupancy sensors; Remark:8514	Procedure Step	Published	09/18/2023 12:05 AM
5291 - Note : It is good practice to verify all cables and connectors are labeled prior to ...	Annotation	Published	10/24/2022 8:35 AM
7291 - Disable both infrared occupancy sensors	Instruction	Published	05/01/2023 8:15 AM
8514 - Verify sensors mounted in control pillar door are receivers.	Remark	Published	09/29/2023 11:52 AM
9205 - To disconnect sensor cable, turn collar counterclockwise and pull away from s...	Remark	Published	09/29/2023 11:52 AM
7479 - 7417 - Prepare New Occupancy Sensor; Remark:	Procedure Step	Published	06/02/2023 6:13 PM
7417 - Prepare New Occupancy Sensor	Instruction	Published	06/02/2023 1:39 PM
7456 - 7418 - Remove cover from new occupancy sensor; Remark:7419	Procedure Step	Published	06/02/2023 5:27 PM
7418 - Remove cover from new occupancy sensor	Instruction	Published	06/02/2023 1:43 PM
7419 - Use a slotted screwdriver to pry the cover off from the side.	Remark	Published	04/13/2025 5:44 PM
7457 - 7420 - Verify narrow field radar antenna is installed; Remark:7421	Procedure Step	Published	04/13/2025 6:18 PM
7420 - Verify narrow field radar antenna is installed	Instruction	Published	04/13/2025 5:44 PM
7421 - The IXIO-DT1 should come with the narrow field antenna installed.	Remark	Published	06/02/2023 2:14 PM
8901 - If needed, the antenna can be changed. Remove cover. Install narrow field ant...	Remark	Published	09/25/2023 9:51 PM
8889 - 8888 - Prepare Mounting Holes; Remark:	Procedure Step	Published	09/25/2023 4:55 PM
8888 - Prepare Mounting Holes	Instruction	Published	09/25/2023 4:54 PM
8884 - 8883 - Mark mounting hole height; Remark:8882	Procedure Step	Published	09/25/2023 4:58 PM
8883 - Mark mounting hole height	Instruction	Published	09/25/2023 4:56 PM
8882 - Use erasable marker or pencil to draw a level horizontal line. Mounting hole ...	Remark	Published	09/25/2023 4:58 PM
8886 - 8879 - Mark centerline of pedestrian monitor door; Remark:8878	Procedure Step	Published	09/25/2023 5:01 PM
8879 - Mark centerline of pedestrian monitor door	Instruction	Published	09/25/2023 5:00 PM
8878 - Use erasable marker or pencil to draw a vertical line.	Remark	Published	09/25/2023 5:01 PM
8885 - 8881 - Attach mounting template; Remark:8880	Procedure Step	Published	09/25/2023 4:59 PM
8881 - Attach mounting template	Instruction	Published	09/25/2023 4:58 PM
8880 - Template provided with the IXIO-DT1 has a self-adhesive backing. Template may...	Remark	Published	09/25/2023 4:59 PM
8887 - 8877 - Mark location of 3.2-mm (1/8-inch) mounting holes; Remark:8876	Procedure Step	Published	09/25/2023 5:03 PM
8904 - Caution : Ensure placement of mounting holes will not interfere with internal wiring in...	Annotation	Published	09/25/2023 9:57 PM
8877 - Mark location of 3.2-mm (1/8-inch) mounting holes	Instruction	Published	09/25/2023 5:01 PM
8876 - If available, use a center punch and hammer to create a dimple at each mounti...	Remark	Published	09/25/2023 5:01 PM
8905 - 8903 - Mark location of 8-mm (5/16-inch) hole for wire passage; Remark:8902	Procedure Step	Published	09/25/2023 9:58 PM
8903 - Mark location of 8-mm (5/16-inch) hole for wire passage	Instruction	Published	09/25/2023 9:58 PM
8902 - If available, use a center punch and hammer to create a dimple at center of w...	Remark	Published	09/25/2023 9:58 PM
8946 - 8945 - Drill Installation Holes; Remark:	Procedure Step	Published	09/25/2023 10:01 PM
8945 - Drill Installation Holes	Instruction	Published	09/25/2023 10:01 PM
8939 - 8938 - Hold or block the door in an open position; Remark:	Procedure Step	Published	09/25/2023 10:01 PM
8938 - Hold or block the door in an open position	Instruction	Published	09/25/2023 10:01 PM
8940 - 8935 - Drill two (2) mounting holes; Remark:8934	Procedure Step	Published	09/25/2023 10:02 PM
8936 - Warning : Wear protective gloves and eyewear when drilling into cabinet door.	Annotation	Published	09/25/2023 10:05 PM
8937 - Caution : Do not damage interior of RPM when drilling holes.	Annotation	Published	09/25/2023 10:05 PM
8935 - Drill two (2) mounting holes	Instruction	Published	09/25/2023 10:02 PM
8934 - Use a 3.2-mm (1/8-inch) drill bit.	Remark	Published	09/25/2023 10:02 PM
8941 - 8933 - Drill wire passage hole; Remark:8932	Procedure Step	Published	09/25/2023 10:03 PM
8933 - Drill wire passage hole	Instruction	Published	09/25/2023 10:03 PM
8932 - Use an 8-mm (5/16-inch) drill bit.	Remark	Published	09/25/2023 10:03 PM
8942 - 8931 - Clean newly drilled holes; Remark:8930	Procedure Step	Published	09/25/2023 10:04 PM
8931 - Clean newly drilled holes	Instruction	Published	09/25/2023 10:04 PM
8930 - Use the deburring tool	Remark	Published	09/25/2023 10:04 PM
8943 - 8929 - Partially insert two (2) screws into mounting holes; Remark:8928	Procedure Step	Published	09/25/2023 10:06 PM
8929 - Partially insert two (2) screws into mounting holes	Instruction	Published	09/25/2023 10:06 PM
8928 - Mounting screws are included in the IXIO-DT-1 kit. Do not fully tighten screw...	Remark	Published	09/25/2023 10:06 PM
8944 - 8926 - Insert rubber grommet in wire passage hole; Remark:8925	Procedure Step	Published	09/25/2023 10:08 PM
8927 - Note : Protecting wires with a rubber grommet is critical to preventing damage to wi...	Annotation	Published	09/25/2023 10:08 PM
8926 - Insert rubber grommet in wire passage hole	Instruction	Published	09/25/2023 10:07 PM
8925 - rubber grommet	Remark	Published	09/25/2023 10:08 PM
8924 - 8923 - Install IXIO-DT1 Sensor; Remark:	Procedure Step	Published	09/25/2023 10:09 PM
8923 - Install IXIO-DT1 Sensor	Instruction	Published	09/25/2023 10:09 PM
8918 - 8917 - Feed wiring connector through grommet; Remark:8915	Procedure Step	Published	09/25/2023 10:13 PM
8917 - Feed wiring connector through grommet	Instruction	Published	09/25/2023 10:11 PM
8915 - The wiring assembly is included in the IXIO-DT1 kit. Feed loose end of wiring...	Remark	Published	09/25/2023 10:11 PM
8916 - Leave approximately 15 cm (6 in) of wire remaining outside of cabinet.	Remark	Published	09/25/2023 10:13 PM
8919 - 8914 - Mount new sensor; Remark:8912	Procedure Step	Published	09/25/2023 10:15 PM
8914 - Mount new sensor	Instruction	Published	09/25/2023 10:13 PM
8912 - First, slide left side onto mounting screw.	Remark	Published	09/25/2023 10:14 PM
8913 - Then, place right side over mounting screw and push down.	Remark	Published	09/25/2023 10:15 PM
8920 - 8911 - Tighten two (2) mounting screws; Remark:8910	Procedure Step	Published	09/25/2023 10:16 PM
8911 - Tighten two (2) mounting screws	Instruction	Published	09/25/2023 10:15 PM
8910 - Use medium Phillips (PH2) screwdriver. Take care not to overtighten.	Remark	Published	09/25/2023 10:16 PM
8921 - 8909 - Route wiring through clamp and connect; Remark:8908	Procedure Step	Published	09/25/2023 10:18 PM
8909 - Route wiring through clamp and connect	Instruction	Published	09/25/2023 10:16 PM
8908 - route wiring through clamp and connect	Remark	Published	09/25/2023 10:18 PM
8922 - 8907 - Adjust angle of the radar antenna; Remark:8906	Procedure Step	Published	09/25/2023 10:20 PM
8907 - Adjust angle of the radar antenna	Instruction	Published	09/25/2023 10:18 PM
8906 - The angle is adjusted by manually rotating the antenna up or down. The defaul...	Remark	Published	09/25/2023 10:20 PM
8970 - 8969 - Connect Wiring to RPM; Remark:	Procedure Step	Published	09/25/2023 10:23 PM
8969 - Connect Wiring to RPM	Instruction	Published	09/25/2023 10:22 PM
8963 - 8962 - Disconnect existing SPY-2 wiring; Remark:8961	Procedure Step	Published	09/25/2023 10:25 PM
7351 - Note : It is good practice to verify all cables and connectors are labeled prior to ...	Annotation	Published	05/03/2023 11:25 AM
8962 - Disconnect existing SPY-2 wiring	Instruction	Published	09/25/2023 10:24 PM
8961 - Do not remove existing occupancy sensor from door panel. Disconnect SPY-2 wir...	Remark	Published	09/25/2023 10:24 PM
8964 - 8960 - Route new cable to TB2; Remark:8959	Procedure Step	Published	09/25/2023 10:26 PM
8960 - Route new cable to TB2	Instruction	Published	09/25/2023 10:25 PM
8959 - New IXIO-DT1 cable should be routed along existing SPY-2 cable. Cable ties ma...	Remark	Published	09/25/2023 10:26 PM
8965 - 8958 - Connect red wire to TB2, Pin 16; Remark:8956	Procedure Step	Published	09/25/2023 10:30 PM
7263 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	04/24/2023 2:32 PM
8958 - Connect red wire to TB2, Pin 16	Instruction	Published	09/25/2023 10:27 PM
8956 - Red is power (+12 VDC) wire.	Remark	Published	09/25/2023 10:29 PM
8957 - For models with older terminal blocks, it may be necessary to use a fork conn...	Remark	Published	09/25/2023 10:30 PM
8966 - 8955 - Connect both black and white wires to TB2, Pin 15; Remark:8954	Procedure Step	Published	09/25/2023 10:32 PM
8955 - Connect both black and white wires to TB2, Pin 15	Instruction	Published	09/25/2023 10:31 PM
8954 - Black is the ground wire. White is the common wire	Remark	Published	09/25/2023 10:32 PM
8967 - 8953 - Connect green wire to TB2, Pin 6; Remark:8952	Procedure Step	Published	09/25/2023 10:34 PM
8953 - Connect green wire to TB2, Pin 6	Instruction	Published	09/25/2023 10:33 PM
8952 - Green is the occupancy signal to the SCA-775 module.	Remark	Published	09/25/2023 10:34 PM
8968 - 8951 - Apply sealant if needed; Remark:8950	Procedure Step	Published	09/25/2023 10:35 PM
8951 - Apply sealant if needed	Instruction	Published	09/25/2023 10:34 PM
8950 - Access wire penetration hole from back of the RPM door.	Remark	Published	09/25/2023 10:35 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
8949 - 8948 - Hold door open; Remark:8947	Procedure Step	Published	09/25/2023 10:37 PM
8948 - Hold door open	Instruction	Published	09/25/2023 10:37 PM
8947 - Do not move door. Door must remain stationary to prevent occupancy.	Remark	Published	09/25/2023 10:37 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7281 - 7252 - Verify RPM start-up; Remark:7253	Procedure Step	Published	04/20/2025 3:26 PM
7252 - Verify RPM start-up	Instruction	Published	04/27/2023 2:23 PM
7253 - RPM will perform a power on self-test (POST) and collect a background radiati...	Remark	Published	05/10/2023 3:14 PM
7470 - 7442 - Generate occupancy; Remark:7443	Procedure Step	Published	06/02/2023 5:37 PM
7442 - Generate occupancy	Instruction	Published	06/02/2023 4:19 PM
7443 - Create motion in front of occupancy sensor. While holding the door open and s...	Remark	Published	06/02/2023 4:21 PM
7471 - 7444 - Verify occupancy sensor functionality; Remark:7445	Procedure Step	Published	06/02/2023 5:38 PM
7444 - Verify occupancy sensor functionality	Instruction	Published	06/02/2023 4:32 PM
7445 - IXIO-DT1 green sensor light will illuminate.	Remark	Published	06/02/2023 4:35 PM
8973 - Left latch on the LCD screen will indicate a “closed” circuit.	Remark	Published	09/25/2023 11:05 PM
8974 - SC-770 status will read “OCCUPIED”.	Remark	Published	09/25/2023 11:06 PM
7472 - 7446 - Install sensor cover; Remark:7447	Procedure Step	Published	06/02/2023 5:38 PM
7446 - Install sensor cover	Instruction	Published	06/02/2023 4:37 PM
7447 - The cover should snap into place.	Remark	Published	06/02/2023 4:38 PM
7473 - 7448 - If needed, apply sealant; Remark:7449	Procedure Step	Published	06/02/2023 5:39 PM
7448 - If needed, apply sealant	Instruction	Published	06/02/2023 4:39 PM
7449 - If used outdoors, sealant should be applied to top and sides of cover. Do not...	Remark	Published	06/02/2023 4:41 PM
8587 - 7305 - Enable both infrared occupancy sensors; Remark:8559	Procedure Step	Published	09/17/2023 11:03 PM
5553 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	10/28/2022 2:19 PM
7305 - Enable both infrared occupancy sensors	Instruction	Published	05/01/2023 8:33 AM
8559 - To reconnect sensor cable, align connectors, push towards sensor, and turn co...	Remark	Published	09/29/2023 12:05 PM
7474 - 7310 - Enable tamper switches; Remark:7451	Procedure Step	Published	06/02/2023 5:41 PM
7310 - Enable tamper switches	Instruction	Published	05/01/2023 8:36 AM
7451 - Remove magnets and/or adhesive tape from door tamper switches.	Remark	Published	04/13/2025 5:46 PM
7282 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	04/27/2023 4:15 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
9385 - 319 - Perform operational test; Remark:9347	Procedure Step	Published	06/16/2025 5:15 PM
319 - Perform operational test	Instruction	Published	06/10/2021 8:31 PM
9347 - DET-RPM-RAP-RM03 RPM Operational Test.	Remark	Published	10/03/2023 12:11 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
8260 - 8250 - Reopen Lane; Remark:8249	Procedure Step	Published	09/07/2023 3:09 PM
8250 - Reopen Lane	Instruction	Published	09/07/2023 3:09 PM
8249 - Remove orange safety (traffic control) cones	Remark	Published	09/07/2023 3:09 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
minutes	Duration	Published	05/26/2022 11:41 AM
Upon failure of the Visonic SPY-2 infrared curtain occupancy sensor	Frequency	Published	09/25/2023 3:49 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Magnets and adhesive tape to disable door tamper switches	Replacement Parts	Published	06/02/2023 10:08 PM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Cordless drill	Tools	Published	09/25/2023 4:19 PM
3.2-mm (1/8-inch) drill bit (for metal)	Tools	Published	09/25/2023 4:19 PM
8-mm (5/16-inch) drill bit (for metal)	Tools	Published	09/25/2023 4:19 PM
Deburring tool	Tools	Published	09/25/2023 4:20 PM
safety glasses	Replacement Parts	Published	07/02/2023 4:48 PM
Gloves (heavy duty)	Tools	Published	09/25/2023 4:20 PM
Wire stripper	Tools	Published	09/25/2023 4:20 PM
Wire crimping tool	Tools	Published	09/25/2023 4:20 PM
Orange/yellow safety vest	Replacement Parts	Published	04/27/2023 6:56 PM
Safety shoes	Replacement Parts	Published	04/27/2023 6:56 PM
Protective headwear: glasses, hard hat	Replacement Parts	Published	05/10/2023 3:31 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
Disconnect Ethernet cable on top of SC-770 box	រូបភាព	Published	10/04/2023 2:59 PM
LD-260 Disconnect Switch Power Off	រូបភាព	Published	04/24/2023 12:49 PM
Disable tamper switch	រូបភាព	Published	09/07/2023 8:22 PM
Disable Tamper Switch	រូបភាព	Published	06/02/2023 2:28 PM
Infrared Receiver	រូបភាព	Published	09/17/2023 7:09 PM
Infrared Receiver DC	រូបភាព	Published	09/29/2023 11:47 AM
Infrared Disconnect Sensor Cable	រូបភាព	Published	09/17/2023 7:11 PM
Infrared Sensor Disconnect	រូបភាព	Published	09/17/2023 7:12 PM
Remove Occupancy Sensor Cover	រូបភាព	Published	06/02/2023 2:38 PM
The IXIO-DT1 should come with the narrow field antenna installed	រូបភាព	Published	09/25/2023 8:35 PM
Verify narrow field radar antenna is installed	រូបភាព	Published	09/25/2023 8:38 PM
Verify narrow field radar antenna is installed 2	រូបភាព	Published	09/25/2023 8:39 PM
Mark mounting hole height	រូបភាព	Published	09/25/2023 8:40 PM
Mark centerline of pedestrian monitor door	រូបភាព	Published	09/25/2023 8:42 PM
Attach mounting template	រូបភាព	Published	09/25/2023 8:44 PM
Mark location of 3.2-mm (1/8-inch) mounting holes	រូបភាព	Published	09/25/2023 8:46 PM
Mark location of 8-mm (5/16-inch) hole for wire passage	រូបភាព	Published	09/25/2023 8:47 PM
Insert rubber grommet in wire passage hole	រូបភាព	Published	09/25/2023 8:48 PM
Feed wiring connector through grommet	រូបភាព	Published	09/25/2023 8:50 PM
Feed wiring connector through grommet2	រូបភាព	Published	09/25/2023 8:51 PM
Mount new sensor	រូបភាព	Published	09/25/2023 8:52 PM
Mount new sensor2	រូបភាព	Published	09/25/2023 8:53 PM
Tighten two (2) mounting screws	រូបភាព	Published	09/25/2023 8:54 PM
Route wiring through clamp and connect	រូបភាព	Published	09/25/2023 8:55 PM
Adjust angle of the radar antenna	រូបភាព	Published	09/25/2023 8:56 PM
Adjust angle of the radar antenna2	រូបភាព	Published	09/25/2023 8:58 PM
Disconnect existing SPY-2 wiring	រូបភាព	Published	09/25/2023 8:59 PM
Route new cable to TB2	រូបភាព	Published	09/25/2023 9:01 PM
Connect red wire to TB2, Pin 16	រូបភាព	Published	09/25/2023 9:02 PM
Connect red wire to TB2, Pin 16 (2)	រូបភាព	Published	09/25/2023 9:03 PM
fork connector	រូបភាព	Published	09/25/2023 9:04 PM
Connect both black and white wires to TB2, Pin 15	រូបភាព	Published	09/25/2023 9:06 PM
Connect green wire to TB2, Pin 6	រូបភាព	Published	09/25/2023 9:34 PM
Apply sealant if needed	រូបភាព	Published	09/25/2023 9:36 PM
LD-260 Disconnect Switch Power On	រូបភាព	Published	06/04/2025 1:28 PM
IXIO-DT1 green sensor light will illuminate	រូបភាព	Published	09/25/2023 9:37 PM
Verify occupancy sensor functionality	រូបភាព	Published	09/25/2023 9:38 PM
Verify occupancy sensor functionality2	រូបភាព	Published	09/25/2023 9:39 PM
Install Occupancy Sensor Cover	រូបភាព	Published	06/02/2023 4:26 PM
Occupancy Sensor Sealant Application	រូបភាព	Published	06/02/2023 4:30 PM
Infrared Connection	រូបភាព	Published	09/29/2023 12:02 PM
Infrared Cable Installation	រូបភាព	Published	09/17/2023 10:12 PM
Infrared Sensor Cable	រូបភាព	Published	09/17/2023 10:13 PM
Remove Magnet from Tamper.PNG	រូបភាព	Published	09/28/2023 9:37 AM
Remove Magnet on Tamper Switch	រូបភាព	Published	06/02/2023 4:31 PM

DET-RPM-RAP-CM15

Install the BEA IXIO-DT1 occupancy sensor on the pedestrian radiation portal monitor (RPM). The existing Visonic SPY-2 infrared curtain sensor is abandoned in place.

Equipment Hierarchy

Rapiscan PM-700 Pedestrian Monitor

Frequency

Upon failure of the Visonic SPY-2 infrared curtain occupancy sensor

Technician Level

Kỹ thuật viên 2

x 2

Duration

Time increment

minutes

Length of time

120

Tools Required

Keys to access RPM

Magnets and adhesive tape to disable door tamper switches

Medium Phillips (PH2) screwdriver

Cordless drill

3.2-mm (1/8-inch) drill bit (for metal)

8-mm (5/16-inch) drill bit (for metal)

Deburring tool

safety glasses

Gloves (heavy duty)

Wire stripper

Wire crimping tool

Orange/yellow safety vest

Safety shoes

Protective headwear: glasses, hard hat

Orange traffic cones

Materials Required

BEA IXIO-DT1 Dual Technology Occupancy Sensor (Rapiscan Part #6692W)

Wiring crimp connector, fork type, 18-20 gauge

Silicone sealant, or equivalent

8-mm (5/16-inch) rubber hole grommet

Cable ties, or equivalent

Originators

Brian Tucker

Erica Kilgannon

Mark Melany

Originating Organization

Rapiscan Systems; PNNL

Approver

Cody Hostick

Additional Retest Requirements Information

Verify occupancy sensor functionality

Final Documentation

Corrective maintenance report

Departmental Coordination

Prior to arrival, notify operators concerning expected work, duration, and anticipated alarms and fault indications.

Date of Origin

2021-07-01

Version #

Revision Description

Updated LD-260 images to re-usable standardized content. Updated instructions to standardized re-usable content.

Revision Date

2023-09-25

Revision Author

Paul Francik

Step 1

Main Step

7264 - 1401 - Thiết lập các Điều kiện Ban đầu; Remark:

Step 00

1401 - Thiết lập các Điều kiện Ban đầu

Thiết lập các Điều kiện Ban đầu

7622 - 7592 - Thông báo cho cán bộ vận hành sau khi đến; Remark:11335

Step 00

7592 - Thông báo cho cán bộ vận hành sau khi đến

Thông báo cho cán bộ vận hành sau khi đến

11335 - Upon arrival, brief system operators on expected work, duration, anticipated ...

Upon arrival, brief system operators on expected work, duration, anticipated alarms, and fault indications before starting work.

7452 - 7231 - Close lane; Remark:7415

Step 00

7231 - Close lane

Close lane

7415 - Re-route pedestrian traffic.

Re-route pedestrian traffic.

7269 - 7232 - Mở cửa hộp tủ máy RPM; Remark:7234

Step 00

7232 - Mở cửa hộp tủ máy RPM

Mở cửa hộp tủ máy RPM

7234 - Mở tất cả các cửa cần thiết để tiếp cận các bộ phận.

Mở tất cả các cửa cần thiết để tiếp cận các bộ phận.

7755 - 7679 - Ngắt kết nối đầu nối Ethernet ra khỏi phía trên bộ điều khiển SC-770 của máy RPM; Remark:11336

7680- : Nhớ nhấn nút nhả ở phía sau của cáp Ethernet trước khi gỡ đầu dây.

Type

Thận trọng

Nhớ nhấn nút nhả ở phía sau của cáp Ethernet trước khi gỡ đầu dây.

Step 00

7679 - Ngắt kết nối Ethernet

Ngắt kết nối Ethernet

11336 - Locate Ethernet connector on top of SC-770 controller. Press release button o...

Locate Ethernet connector on top of SC-770 controller. Press release button on back of connector. Pull connector.

Disconnect Ethernet cable on top of SC-770 box

7270 - 7235 - Tắt nguồn máy RPM; Remark:7236

Step 00

7235 - Tắt nguồn máy RPM

Tắt nguồn máy RPM

7236 - Xoay công tắc LD-260 về vị trí TẮT. Đèn LED PWR ON sẽ bật.

Xoay công tắc LD-260 về vị trí TẮT. Đèn LED PWR ON sẽ bật.

7454 - 7290 - Tắt công tắc chống can thiệp thiết bị; Remark:7416

Step 00

7290 - Tắt công tắc chống can thiệp thiết bị

Tắt công tắc chống can thiệp thiết bị

7416 - Sử dụng nam châm để vô hiệu hóa công tắc chống can thiệp thiết bị đối với tất cả...

Sử dụng nam châm để vô hiệu hóa công tắc chống can thiệp thiết bị đối với tất cả các cửa đang mở. Sử dụng băng dính để vô hiệu hóa các công tắc cơ học loại cũ.

Use a magnet to disable tamper switches for all open doors

8561 - 7291 - Tắt cả hai cảm biến hồng ngoại hiện diện; Remark:8514

5291- : Tốt nhất là nên kiểm tra để đảm bảo tất cả dây cáp và đầu nối đã được dán nhãn t...

Type

Lưu ý

Tốt nhất là nên kiểm tra để đảm bảo tất cả dây cáp và đầu nối đã được dán nhãn trước khi ngắt kết nối.

Step 00

7291 - Tắt cả hai cảm biến hồng ngoại hiện diện

Tắt cả hai cảm biến hồng ngoại hiện diện

8514 - Kiểm tra xem các cảm biến gắn ở cột chính có đúng là bộ thu hay không.

Kiểm tra xem các cảm biến gắn ở cột chính có đúng là bộ thu hay không.

9205 - Để ngắt kết nối cáp cảm biến, vặn vòng đai cáp ngược chiều kim đồng hồ và kéo ra...

Để ngắt kết nối cáp cảm biến, vặn vòng đai cáp ngược chiều kim đồng hồ và kéo ra khỏi cảm biến.

Step 2

Main Step

7479 - 7417 - Prepare New Occupancy Sensor; Remark:

Step 00

7417 - Prepare New Occupancy Sensor

Prepare New Occupancy Sensor

7456 - 7418 - Remove cover from new occupancy sensor; Remark:7419

Step 00

7418 - Remove cover from new occupancy sensor

Remove cover from new occupancy sensor

7419 - Use a slotted screwdriver to pry the cover off from the side.

Use a slotted screwdriver to pry the cover off from the side.

7457 - 7420 - Verify narrow field radar antenna is installed; Remark:7421

Step 00

7420 - Verify narrow field radar antenna is installed

Verify narrow field radar antenna is installed

7421 - The IXIO-DT1 should come with the narrow field antenna installed.

The IXIO-DT1 should come with the narrow field antenna installed.

verify the IXIO-DT1 field antenna installed.

8901 - If needed, the antenna can be changed. Remove cover. Install narrow field ant...

If needed, the antenna can be changed. Remove cover. Install narrow field antenna stored in slot behind antenna mount. Replace cover.

Step 3

Main Step

8889 - 8888 - Prepare Mounting Holes; Remark:

Step 00

8888 - Prepare Mounting Holes

Prepare Mounting Holes

8884 - 8883 - Mark mounting hole height; Remark:8882

Step 00

8883 - Mark mounting hole height

Mark mounting hole height

8882 - Use erasable marker or pencil to draw a level horizontal line. Mounting hole ...

Use erasable marker or pencil to draw a level horizontal line. Mounting hole height is 35 cm from top of cabinet door.

8886 - 8879 - Mark centerline of pedestrian monitor door; Remark:8878

Step 00

8879 - Mark centerline of pedestrian monitor door

Mark centerline of pedestrian monitor door

8878 - Use erasable marker or pencil to draw a vertical line.

Use erasable marker or pencil to draw a vertical line.

8885 - 8881 - Attach mounting template; Remark:8880

Step 00

8881 - Attach mounting template

Attach mounting template

8880 - Template provided with the IXIO-DT1 has a self-adhesive backing. Template may...

Template provided with the IXIO-DT1 has a self-adhesive backing. Template may differ from picture shown. Match template lines with vertical and horizontal marks.

8887 - 8877 - Mark location of 3.2-mm (1/8-inch) mounting holes; Remark:8876

8904 - Caution : Ensure placement of mounting holes will not interfere with internal wiring in...

Type

Caution

Ensure placement of mounting holes will not interfere with internal wiring in the cabinet.

Step 00

8877 - Mark location of 3.2-mm (1/8-inch) mounting holes

Mark location of 3.2-mm (1/8-inch) mounting holes

8876 - If available, use a center punch and hammer to create a dimple at each mounti...

If available, use a center punch and hammer to create a dimple at each mounting hole location.

8905 - 8903 - Mark location of 8-mm (5/16-inch) hole for wire passage; Remark:8902

Step 00

8903 - Mark location of 8-mm (5/16-inch) hole for wire passage

Mark location of 8-mm (5/16-inch) hole for wire passage

8902 - If available, use a center punch and hammer to create a dimple at center of w...

If available, use a center punch and hammer to create a dimple at center of wire passage hole.

Step 4

Main Step

8946 - 8945 - Drill Installation Holes; Remark:

Step 00

8945 - Drill Installation Holes

Drill Installation Holes

8939 - 8938 - Hold or block the door in an open position; Remark:

Step 00

8938 - Hold or block the door in an open position

Hold or block the door in an open position

8940 - 8935 - Drill two (2) mounting holes; Remark:8934

8936 - Warning : Wear protective gloves and eyewear when drilling into cabinet door.

Type

Warning

Wear protective gloves and eyewear when drilling into cabinet door.

8937 - Caution : Do not damage interior of RPM when drilling holes.

Type

Caution

Do not damage interior of RPM when drilling holes.

Step 00

8935 - Drill two (2) mounting holes

Drill two (2) mounting holes

8934 - Use a 3.2-mm (1/8-inch) drill bit.

Use a 3.2-mm (1/8-inch) drill bit.

8941 - 8933 - Drill wire passage hole; Remark:8932

Step 00

8933 - Drill wire passage hole

Drill wire passage hole

8932 - Use an 8-mm (5/16-inch) drill bit.

Use an 8-mm (5/16-inch) drill bit.

8942 - 8931 - Clean newly drilled holes; Remark:8930

Step 00

8931 - Clean newly drilled holes

Clean newly drilled holes

8930 - Use the deburring tool

Use the deburring tool

8943 - 8929 - Partially insert two (2) screws into mounting holes; Remark:8928

Step 00

8929 - Partially insert two (2) screws into mounting holes

Partially insert two (2) screws into mounting holes

8928 - Mounting screws are included in the IXIO-DT-1 kit. Do not fully tighten screw...

Mounting screws are included in the IXIO-DT-1 kit. Do not fully tighten screws. Enough room should be available to slide the sensor in place.

8944 - 8926 - Insert rubber grommet in wire passage hole; Remark:8925

8927 - Note : Protecting wires with a rubber grommet is critical to preventing damage to wi...

Type

Note

Protecting wires with a rubber grommet is critical to preventing damage to wiring and possible equipment malfunctions.

Step 00

8926 - Insert rubber grommet in wire passage hole

Insert rubber grommet in wire passage hole

8925 - rubber grommet

place rubber grommet in wire passage hole

Step 5

Main Step

8924 - 8923 - Install IXIO-DT1 Sensor; Remark:

Step 00

8923 - Install IXIO-DT1 Sensor

Install IXIO-DT1 Sensor

8918 - 8917 - Feed wiring connector through grommet; Remark:8915

Step 00

8917 - Feed wiring connector through grommet

Feed wiring connector through grommet

8915 - The wiring assembly is included in the IXIO-DT1 kit. Feed loose end of wiring...

The wiring assembly is included in the IXIO-DT1 kit. Feed loose end of wiring assembly through hole.

8916 - Leave approximately 15 cm (6 in) of wire remaining outside of cabinet.

Leave approximately 15 cm (6 in) of wire remaining outside of cabinet.

leave 15 cm (6 in) of wire outside of cabinet

8919 - 8914 - Mount new sensor; Remark:8912

Step 00

8914 - Mount new sensor

Mount new sensor

8912 - First, slide left side onto mounting screw.

First, slide left side onto mounting screw.

8913 - Then, place right side over mounting screw and push down.

Then, place right side over mounting screw and push down.

8920 - 8911 - Tighten two (2) mounting screws; Remark:8910

Step 00

8911 - Tighten two (2) mounting screws

Tighten two (2) mounting screws

8910 - Use medium Phillips (PH2) screwdriver. Take care not to overtighten.

Use medium Phillips (PH2) screwdriver. Take care not to overtighten.

8921 - 8909 - Route wiring through clamp and connect; Remark:8908

Step 00

8909 - Route wiring through clamp and connect

Route wiring through clamp and connect

8908 - route wiring through clamp and connect

8922 - 8907 - Adjust angle of the radar antenna; Remark:8906

Step 00

8907 - Adjust angle of the radar antenna

Adjust angle of the radar antenna

8906 - The angle is adjusted by manually rotating the antenna up or down. The defaul...

The angle is adjusted by manually rotating the antenna up or down. The default angle is approximately 15 degrees.

Step 6

Main Step

8970 - 8969 - Connect Wiring to RPM; Remark:

Step 00

8969 - Connect Wiring to RPM

Connect Wiring to RPM

8963 - 8962 - Disconnect existing SPY-2 wiring; Remark:8961

7351 - Note : It is good practice to verify all cables and connectors are labeled prior to ...

Type

Note

It is good practice to verify all cables and connectors are labeled prior to disconnection.

Step 00

8962 - Disconnect existing SPY-2 wiring

Disconnect existing SPY-2 wiring

8961 - Do not remove existing occupancy sensor from door panel. Disconnect SPY-2 wir...

Do not remove existing occupancy sensor from door panel. Disconnect SPY-2 wiring from terminal block 2 (TB2). Existing wiring is normally connected at pin 16, pin 15, and pin 6.

8964 - 8960 - Route new cable to TB2; Remark:8959

Step 00

8960 - Route new cable to TB2

Route new cable to TB2

8959 - New IXIO-DT1 cable should be routed along existing SPY-2 cable. Cable ties ma...

New IXIO-DT1 cable should be routed along existing SPY-2 cable. Cable ties may be used to secure new wiring to existing wiring.

8965 - 8958 - Connect red wire to TB2, Pin 16; Remark:8956

7263 - Caution : Correct placement of connectors and wiring is critical to proper operation.

Type

Caution

Correct placement of connectors and wiring is critical to proper operation.

Step 00

8958 - Connect red wire to TB2, Pin 16

Connect red wire to TB2, Pin 16

8956 - Red is power (+12 VDC) wire.

Red is power (+12 VDC) wire.

8957 - For models with older terminal blocks, it may be necessary to use a fork conn...

For models with older terminal blocks, it may be necessary to use a fork connector.

older model may need to use a fork connector

8966 - 8955 - Connect both black and white wires to TB2, Pin 15; Remark:8954

Step 00

8955 - Connect both black and white wires to TB2, Pin 15

Connect both black and white wires to TB2, Pin 15

8954 - Black is the ground wire. White is the common wire

Black is the ground wire. White is the common wire

8967 - 8953 - Connect green wire to TB2, Pin 6; Remark:8952

Step 00

8953 - Connect green wire to TB2, Pin 6

Connect green wire to TB2, Pin 6

8952 - Green is the occupancy signal to the SCA-775 module.

Green is the occupancy signal to the SCA-775 module.

8968 - 8951 - Apply sealant if needed; Remark:8950

Step 00

8951 - Apply sealant if needed

Apply sealant if needed

8950 - Access wire penetration hole from back of the RPM door.

Access wire penetration hole from back of the RPM door.

Step 7

Main Step

7279 - 7249 - Đưa thiết bị trở lại điều kiện hoạt động bình thường; Remark:

Step 00

7249 - Đưa thiết bị trở lại điều kiện hoạt động bình thường

Đưa thiết bị trở lại điều kiện hoạt động bình thường

8949 - 8948 - Hold door open; Remark:8947

Step 00

8948 - Hold door open

Hold door open

8947 - Do not move door. Door must remain stationary to prevent occupancy.

Do not move door. Door must remain stationary to prevent occupancy.

7280 - 7250 - Bật nguồn máy RPM; Remark:7251

Step 00

7250 - Bật nguồn máy RPM

Bật nguồn máy RPM

7251 - Xoay công tắc LD-260 về vị trí BẬT. Đèn LED PWR ON sẽ bật sáng.

Xoay công tắc LD-260 về vị trí BẬT. Đèn LED PWR ON sẽ bật sáng.

7281 - 7252 - Kiểm tra để xác định SC-770 đã có điện; Remark:7253

Step 00

7252 - Kiểm tra để xác định SC-770 đã có điện

Kiểm tra để xác định SC-770 đã có điện

7253 - Bộ điều khiển SC-770 sẽ được bật nguồn, thực hiện bước Tự kiểm tra khi bật nguồn...

Bộ điều khiển SC-770 sẽ được bật nguồn, thực hiện bước Tự kiểm tra khi bật nguồn (POST) và thu thập dữ liệu đo phông.

7470 - 7442 - Generate occupancy; Remark:7443

Step 00

7442 - Generate occupancy

Generate occupancy

7443 - Create motion in front of occupancy sensor. While holding the door open and s...

Create motion in front of occupancy sensor. While holding the door open and still, wave a hand or walk in front of the sensor.

7471 - 7444 - Verify occupancy sensor functionality; Remark:7445

Step 00

7444 - Verify occupancy sensor functionality

Verify occupancy sensor functionality

7445 - IXIO-DT1 green sensor light will illuminate.

IXIO-DT1 green sensor light will illuminate.

functional sensor will have green light turn on

8973 - Left latch on the LCD screen will indicate a “closed” circuit.

Left latch on the LCD screen will indicate a “closed” circuit.

8974 - SC-770 status will read “OCCUPIED”.

SC-770 status will read “OCCUPIED”.

7472 - 7446 - Install sensor cover; Remark:7447

Step 00

7446 - Install sensor cover

Install sensor cover

7447 - The cover should snap into place.

The cover should snap into place.

7473 - 7448 - If needed, apply sealant; Remark:7449

Step 00

7448 - If needed, apply sealant

If needed, apply sealant

7449 - If used outdoors, sealant should be applied to top and sides of cover. Do not...

If used outdoors, sealant should be applied to top and sides of cover. Do not apply sealant along bottom of cover. Remove excess silicone with mineral spirits and rags.