RPM IXIO-DT1 Occupancy Sensor Replacement | FRONTLINE Maintenance Tool

Last Updated: 04/24/2025 1:43 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
7478 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	09/01/2023 7:48 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7452 - 7231 - Close lane; Remark:7415	Procedure Step	Published	06/02/2023 5:12 PM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7415 - Re-route pedestrian traffic.	Remark	Published	06/02/2023 1:08 PM
7453 - 7232 - Open RPM door; Remark:7267	Procedure Step	Published	06/02/2023 5:24 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7267 - Open all doors needed to access components.	Remark	Published	09/16/2023 4:54 PM
7454 - 7290 - Disable tamper switches; Remark:7416	Procedure Step	Published	06/02/2023 5:25 PM
7290 - Disable tamper switches	Instruction	Published	05/01/2023 8:14 AM
7416 - Use a magnet to disable tamper switches for all open doors. Use adhesive tape...	Remark	Published	06/02/2023 1:18 PM
7270 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	09/01/2023 7:57 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
7479 - 7417 - Prepare New Occupancy Sensor; Remark:	Procedure Step	Published	06/02/2023 6:13 PM
7417 - Prepare New Occupancy Sensor	Instruction	Published	06/02/2023 1:39 PM
7456 - 7418 - Remove cover from new occupancy sensor; Remark:7419	Procedure Step	Published	06/02/2023 5:27 PM
7418 - Remove cover from new occupancy sensor	Instruction	Published	06/02/2023 1:43 PM
7419 - Use a slotted screwdriver to pry the cover off from the side.	Remark	Published	04/13/2025 5:44 PM
7457 - 7420 - Verify narrow field radar antenna is installed; Remark:7421	Procedure Step	Published	04/13/2025 6:18 PM
7420 - Verify narrow field radar antenna is installed	Instruction	Published	04/13/2025 5:44 PM
7421 - The IXIO-DT1 should come with the narrow field antenna installed.	Remark	Published	06/02/2023 2:14 PM
8901 - If needed, the antenna can be changed. Remove cover. Install narrow field ant...	Remark	Published	09/25/2023 9:51 PM
7480 - 7422 - Uninstall Faulty Occupancy Sensor; Remark:	Procedure Step	Published	06/02/2023 9:42 PM
7422 - Uninstall Faulty Occupancy Sensor	Instruction	Published	06/02/2023 2:16 PM
7458 - 7423 - Remove Cover; Remark:7424	Procedure Step	Published	06/02/2023 5:28 PM
7423 - Remove Cover	Instruction	Published	06/02/2023 2:18 PM
7424 - If needed, use a sharp utility knife to cut sealant around edges of sensor. A...	Remark	Published	06/02/2023 2:21 PM
7459 - 7425 - Disconnect wire connector; Remark:7426	Procedure Step	Published	06/02/2023 5:29 PM
7425 - Disconnect wire connector	Instruction	Published	06/02/2023 2:48 PM
7426 - The wire connector is located on the right side of existing sensor.	Remark	Published	06/02/2023 2:53 PM
7460 - 7427 - Loosen two (2) mounting screws; Remark:7428	Procedure Step	Published	06/02/2023 5:30 PM
7429 - Note : Some existing occupancy sensors are installed using screws and nuts, ...	Annotation	Published	06/02/2023 3:09 PM
7427 - Loosen two (2) mounting screws	Instruction	Published	06/02/2023 2:56 PM
7428 - Use a medium Phillips (PH2) screwdriver. If screws and nuts were used, an adj...	Remark	Published	06/02/2023 3:04 PM
7461 - 7430 - Remove faulty occupancy sensor; Remark:7431	Procedure Step	Published	06/02/2023 5:31 PM
7430 - Remove faulty occupancy sensor	Instruction	Published	06/02/2023 3:11 PM
7431 - If a Wizard G3 sensor is being removed, push up on both sides to free the sen...	Remark	Published	09/29/2023 1:49 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
7481 - 7432 - Install new occupancy sensor; Remark:	Procedure Step	Published	06/02/2023 9:46 PM
7432 - Install new occupancy sensor	Instruction	Published	06/02/2023 3:27 PM
7463 - 7433 - Mount new sensor; Remark:7434	Procedure Step	Published	06/02/2023 5:32 PM
7433 - Mount new sensor	Instruction	Published	06/02/2023 3:29 PM
7434 - First, slide left side onto mounting screw.	Remark	Published	04/13/2025 5:44 PM
9206 - Then, place right side over mounting screw and push down.	Remark	Published	09/29/2023 1:55 PM
7464 - 7435 - Tighten two (2) mounting screws; Remark:7436	Procedure Step	Published	06/02/2023 5:33 PM
7435 - Tighten two (2) mounting screws	Instruction	Published	06/02/2023 3:40 PM
7436 - Use medium Phillips (PH2) screwdriver. Take care not to overtighten.	Remark	Published	04/13/2025 5:45 PM
7482 - 7437 - Route wiring through clamp and connect; Remark:7488	Procedure Step	Published	06/02/2023 10:42 PM
7437 - Route wiring through clamp and connect	Instruction	Published	06/02/2023 3:53 PM
7488 - Clamp and Connect	Remark	Published	06/02/2023 10:49 PM
7465 - 7439 - Adjust angle of the radar antenna; Remark:7438	Procedure Step	Published	04/13/2025 6:19 PM
7439 - Adjust angle of the radar antenna	Instruction	Published	04/13/2025 5:45 PM
7438 - The angle is adjusted by manually rotating the antenna up or down. The defaul...	Remark	Published	09/29/2023 1:58 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7466 - 7440 - Hold door open; Remark:7441	Procedure Step	Published	06/02/2023 5:35 PM
7440 - Hold door open	Instruction	Published	06/02/2023 4:10 PM
7441 - Do not move door. Door must remain stationary to prevent occupancy.	Remark	Published	04/13/2025 5:45 PM
7280 - 7250 - Power on RPM; Remark:7251	Procedure Step	Published	04/27/2023 4:14 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7251 - Move LD-260 switch to ON position. The LED PWR ON	Remark	Published	05/10/2023 3:14 PM
7468 - 7304 - Confirm RPM has restarted correctly; Remark:7487	Procedure Step	Published	06/02/2023 5:36 PM
7304 - Confirm RPM has restarted correctly	Instruction	Published	05/01/2023 8:31 AM
7487 - The SC-770 controller will display "OK" following Power On Self-Test (POST) a...	Remark	Published	06/02/2023 10:35 PM
7282 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	04/27/2023 4:15 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
7470 - 7442 - Generate occupancy; Remark:7443	Procedure Step	Published	06/02/2023 5:37 PM
7442 - Generate occupancy	Instruction	Published	06/02/2023 4:19 PM
7443 - Create motion in front of occupancy sensor. While holding the door open and s...	Remark	Published	06/02/2023 4:21 PM
7471 - 7444 - Verify occupancy sensor functionality; Remark:7445	Procedure Step	Published	06/02/2023 5:38 PM
7444 - Verify occupancy sensor functionality	Instruction	Published	06/02/2023 4:32 PM
7445 - IXIO-DT1 green sensor light will illuminate.	Remark	Published	06/02/2023 4:35 PM
8973 - Left latch on the LCD screen will indicate a “closed” circuit.	Remark	Published	09/25/2023 11:05 PM
8974 - SC-770 status will read “OCCUPIED”.	Remark	Published	09/25/2023 11:06 PM
7472 - 7446 - Install sensor cover; Remark:7447	Procedure Step	Published	06/02/2023 5:38 PM
7446 - Install sensor cover	Instruction	Published	06/02/2023 4:37 PM
7447 - The cover should snap into place.	Remark	Published	06/02/2023 4:38 PM
7473 - 7448 - If needed, apply sealant; Remark:7449	Procedure Step	Published	06/02/2023 5:39 PM
7448 - If needed, apply sealant	Instruction	Published	06/02/2023 4:39 PM
7449 - If used outdoors, sealant should be applied to top and sides of cover. Do not...	Remark	Published	06/02/2023 4:41 PM
7474 - 7310 - Enable tamper switches; Remark:7451	Procedure Step	Published	06/02/2023 5:41 PM
7310 - Enable tamper switches	Instruction	Published	05/01/2023 8:36 AM
7451 - Remove magnets and/or adhesive tape from door tamper switches.	Remark	Published	04/13/2025 5:46 PM
7283 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	09/01/2023 11:45 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
Instrument is not functioning correctly	Frequency	Published	12/19/2022 5:52 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Technician 1	Skill Level	Published	05/14/2020 2:56 PM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Magnets and adhesive tape to disable door tamper switches	Replacement Parts	Published	06/02/2023 10:08 PM
Medium slotted screwdriver	Replacement Parts	Published	06/02/2023 10:08 PM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Adjustable wrench	Replacement Parts	Published	06/02/2023 10:08 PM
Utility knife	Tools	Published	05/19/2020 1:54 PM
Orange/yellow safety vest	Replacement Parts	Published	04/27/2023 6:56 PM
Safety shoes	Replacement Parts	Published	04/27/2023 6:56 PM
Gloves	Replacement Parts	Published	05/10/2023 3:28 PM
Protective headwear: glasses, hard hat	Replacement Parts	Published	05/10/2023 3:31 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
Disable tamper switch	Image	Published	09/07/2023 8:22 PM
Disable Tamper Switch	Image	Published	06/02/2023 2:28 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Remove Occupancy Sensor Cover	Image	Published	06/02/2023 2:38 PM
The IXIO-DT1 should come with the narrow field antenna installed	Image	Published	09/25/2023 8:35 PM
Verify narrow field radar antenna is installed	Image	Published	09/25/2023 8:38 PM
Verify narrow field radar antenna is installed 2	Image	Published	09/25/2023 8:39 PM
Uninstall Occupancy Sensor Cover	Image	Published	06/02/2023 2:37 PM
Disconnect Wire Connector	Image	Published	06/02/2023 2:53 PM
Loosen Two Mounting screws	Image	Published	06/02/2023 3:04 PM
Remove faulty Occupancy Sensor	Image	Published	09/29/2023 1:47 PM
Push Occupancy Sensor to the right	Image	Published	09/29/2023 1:48 PM
Mount new sensor	Image	Published	09/25/2023 8:52 PM
Push Down Over Mounting Screw to Install Occupancy Sensor	Image	Published	06/02/2023 3:51 PM
Tighten Occupancy Sensor Mounting Screws	Image	Published	06/02/2023 3:48 PM
Route wiring through clamp and connect	Image	Published	06/02/2023 3:55 PM
Adjust angle of the radar antenna	Image	Published	09/25/2023 8:56 PM
Adjust angle of the radar antenna2	Image	Published	09/25/2023 8:58 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
IXIO-DT1 green sensor light will illuminate	Image	Published	09/25/2023 9:37 PM
Verify occupancy sensor functionality	Image	Published	09/25/2023 9:38 PM
Verify occupancy sensor functionality2	Image	Published	09/25/2023 9:39 PM
Install Occupancy Sensor Cover	Image	Published	06/02/2023 4:26 PM
Occupancy Sensor Sealant Application	Image	Published	06/02/2023 4:30 PM
Remove Magnet from Tamper.PNG	Image	Published	09/28/2023 9:37 AM
Remove Magnet on Tamper Switch	Image	Published	06/02/2023 4:31 PM

DET-RPM-RAP-CM16

Replace a faulty BEA IXIO-DT1 occupancy sensor. This procedure can also be used to replace a faulty BEA Wizard G3 occupancy sensor.

Equipment Hierarchy

Rapiscan PM-700 Pedestrian Monitor

Frequency

Instrument is not functioning correctly

Technician Level

Teknisyen 1

x 1

Duration

Length of time

Tools Required

Keys to access RPM

Magnets and adhesive tape to disable door tamper switches

Medium slotted screwdriver

Medium Phillips (PH2) screwdriver

Adjustable wrench

Utility knife

Orange/yellow safety vest

Safety shoes

Gloves

Protective headwear: glasses, hard hat

Orange traffic cones

Materials Required

BEA IXIO-DT1 Dual Technology Occupancy Sensor (Rapiscan Part #6692W)

Silicone sealant

Originators

Mike Papp

Brian Tucker

Erica Kilgannon

Originating Organization

Rapiscan Systems; PNNL

Approver

Cody Hostick

Safety Concerns

None

Final Documentation

Corrective Maintenance Report

Departmental Coordination

Prior to arrival, notify operators concerning expected work, duration, and anticipated alarms and fault indications.

Date of Origin

2021-07-01

Hazırlık

Step 1

Main Step

7478 - 1401 - Establish Initial Conditions; Remark:

Step 00

1401 - Establish Initial Conditions

Establish Initial Conditions

7452 - 7231 - Close lane; Remark:7415

Step 00

7415 - Re-route pedestrian traffic.

Re-route pedestrian traffic.

7453 - 7232 - Open RPM door; Remark:7267

Step 00

7267 - Open all doors needed to access components.

Open all doors needed to access components.

7454 - 7290 - Disable tamper switches; Remark:7416

Step 00

7290 - Disable tamper switches

Disable tamper switches

7416 - Use a magnet to disable tamper switches for all open doors. Use adhesive tape...

Use a magnet to disable tamper switches for all open doors. Use adhesive tape to disable older mechanical switches.

7270 - 7235 - Power off RPM; Remark:7236

Step 00

7236 - Move LD-260 switch to OFF position. The PWR ON

Move LD-260 switch to OFF position. The PWR ON LED will turn off.

Çalıştırma

Step 2

Main Step

7479 - 7417 - Prepare New Occupancy Sensor; Remark:

Step 00

7417 - Prepare New Occupancy Sensor

Prepare New Occupancy Sensor

7456 - 7418 - Remove cover from new occupancy sensor; Remark:7419

Step 00

7418 - Remove cover from new occupancy sensor

Remove cover from new occupancy sensor

7419 - Use a slotted screwdriver to pry the cover off from the side.

Use a slotted screwdriver to pry the cover off from the side.

7457 - 7420 - Verify narrow field radar antenna is installed; Remark:7421

Step 00

7420 - Verify narrow field radar antenna is installed

Verify narrow field radar antenna is installed

7421 - The IXIO-DT1 should come with the narrow field antenna installed.

The IXIO-DT1 should come with the narrow field antenna installed.

verify the IXIO-DT1 field antenna installed.

8901 - If needed, the antenna can be changed. Remove cover. Install narrow field ant...

If needed, the antenna can be changed. Remove cover. Install narrow field antenna stored in slot behind antenna mount. Replace cover.

Çalıştırma

Step 3

Main Step

7480 - 7422 - Uninstall Faulty Occupancy Sensor; Remark:

Step 00

7422 - Uninstall Faulty Occupancy Sensor

Uninstall Faulty Occupancy Sensor

7458 - 7423 - Remove Cover; Remark:7424

Step 00

7424 - If needed, use a sharp utility knife to cut sealant around edges of sensor. A...

If needed, use a sharp utility knife to cut sealant around edges of sensor. A slotted screwdriver is needed to remove the cover.

7459 - 7425 - Disconnect wire connector; Remark:7426

Step 00

7425 - Disconnect wire connector

Disconnect wire connector

7426 - The wire connector is located on the right side of existing sensor.

The wire connector is located on the right side of existing sensor.

7460 - 7427 - Loosen two (2) mounting screws; Remark:7428

7429 - Note : Some existing occupancy sensors are installed using screws and nuts, ...

Type

Note

Some existing occupancy sensors are installed using screws and nuts, others are installed using self tapping screws.
Removal and replacement only requires mounting screws to be loose, not completely removed.

Step 00

7427 - Loosen two (2) mounting screws

Loosen two (2) mounting screws

7428 - Use a medium Phillips (PH2) screwdriver. If screws and nuts were used, an adj...

Use a medium Phillips (PH2) screwdriver. If screws and nuts were used, an adjustable wrench may be needed.

7461 - 7430 - Remove faulty occupancy sensor; Remark:7431

Step 00

7430 - Remove faulty occupancy sensor

Remove faulty occupancy sensor

7431 - If a Wizard G3 sensor is being removed, push up on both sides to free the sen...

If a Wizard G3 sensor is being removed, push up on both sides to free the sensor from the mounting screws. If an IXIO-DT1 sensor is being removed, push up on right side and slide sensor to the right.

3397 - 3395 - Arızalı bileşeni etiketleyin; Remark:3396

Step 00

3395 - Arızalı bileşeni etiketleyin

Arızalı bileşeni etiketleyin

3396 - Etiket veya bant kullanın. Çıkarıldığı tarihi, arıza belirtilerinin açıklamasını...

Etiket veya bant kullanın. Çıkarıldığı tarihi, arıza belirtilerinin açıklamasını, ülkeyi, sahayı ve şerit numarasını ekleyin. Nükleer Kaçakçılık Tespiti ve Caydırıcılık (NSDD) kılavuzuna veya sözleşme gereksinimlerine göre imha edin.

Çalıştırma

Step 4

Main Step