RPM Ethernet-to-Fiber Media Converter Replacement

Last Updated: 04/24/2025 1:43 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
Rapiscan PM-700 Pedestrian Monitor	Device	Published	06/20/2024 11:38 AM
Rapiscan VM-250 Vehicle Monitor	Device	Published	10/14/2024 9:50 AM
Rapiscan TM-850 Rail Monitor	Device	Published	09/18/2024 10:28 AM
7371 - 1401 - Establish Initial Conditions; Remark:	Procedure Step	Published	05/04/2023 4:11 PM
1401 - Establish Initial Conditions	Instruction	Published	09/30/2022 3:14 PM
7372 - 7231 - Close lane; Remark:7233	Procedure Step	Published	09/01/2023 7:52 PM
7261 - Warning : Traffic should temporarily be rerouted or halted during this procedure to ens...	Annotation	Published	09/28/2023 2:09 PM
7231 - Close lane	Instruction	Published	04/18/2023 1:00 PM
7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...	Remark	Published	04/24/2023 12:18 PM
7373 - 7232 - Open RPM door; Remark:7267	Procedure Step	Published	09/01/2023 7:55 PM
7232 - Open RPM door	Instruction	Published	04/18/2023 1:02 PM
7267 - Open all doors needed to access components.	Remark	Published	09/16/2023 4:54 PM
7374 - 7235 - Power off RPM; Remark:7236	Procedure Step	Published	05/04/2023 4:15 PM
7235 - Power off RPM	Instruction	Published	04/24/2023 12:30 PM
7236 - Move LD-260 switch to OFF position. The PWR ON	Remark	Published	04/27/2023 4:25 PM
7375 - 7356 - Uninstall Faulty Media Converter; Remark:	Procedure Step	Published	05/04/2023 4:17 PM
7356 - Uninstall Faulty Media Converter	Instruction	Published	05/11/2023 12:29 PM
7376 - 7357 - Disconnect Ethernet and optical cables; Remark:7358	Procedure Step	Published	05/04/2023 4:19 PM
5291 - Note : It is good practice to verify all cables and connectors are labeled prior to ...	Annotation	Published	10/24/2022 8:35 AM
7357 - Disconnect Ethernet and optical cables	Instruction	Published	05/11/2023 12:30 PM
7358 - Magnum CS14P Premium Rated Converter Switch	Remark	Published	05/04/2023 1:42 PM
7377 - 7295 - Disconnect power wires; Remark:7359	Procedure Step	Published	05/04/2023 4:20 PM
7295 - Disconnect power wires	Instruction	Published	05/01/2023 8:20 AM
7359 - Use a small precision screwdriver to loosen the screw	Remark	Published	05/11/2023 12:34 PM
7378 - 5405 - Remove two (2) mounting screws; Remark:7360	Procedure Step	Published	05/04/2023 4:21 PM
5405 - Remove two (2) mounting screws	Instruction	Published	10/27/2022 3:28 PM
7360 - Use medium Phillips head (PH2) screwdriver. Retain screws.	Remark	Published	05/11/2023 12:35 PM
7379 - 7361 - Remove faulty media converter; Remark:	Procedure Step	Published	05/04/2023 4:23 PM
7361 - Remove faulty media converter	Instruction	Published	05/11/2023 12:36 PM
3397 - 3395 - Label faulty component; Remark:3396	Procedure Step	Published	07/21/2024 6:59 AM
3395 - Label faulty component	Instruction	Published	08/07/2021 11:07 AM
3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...	Remark	Published	08/09/2021 11:35 AM
7381 - 7362 - Install New Ethernet-to-Fiber Media Converter; Remark:	Procedure Step	Published	05/04/2023 4:25 PM
7362 - Install New Ethernet-to-Fiber Media Converter	Instruction	Published	05/11/2023 12:38 PM
7382 - 7363 - Mount new media converter with two (2) screws; Remark:7396	Procedure Step	Published	05/04/2023 4:53 PM
7363 - Mount new media converter with two (2) screws	Instruction	Published	05/11/2023 12:38 PM
7396 - Use retained screws. Use medium Phillips (PH2) screwdriver.	Remark	Published	05/10/2023 9:11 AM
7397 -	Remark	Published	05/04/2023 4:53 PM
7383 - 7301 - Reconnect power wires; Remark:7364	Procedure Step	Published	05/04/2023 4:27 PM
462 - Caution : Correct placement of connectors and wiring is critical to proper operation.	Annotation	Published	09/28/2023 2:13 PM
7301 - Reconnect power wires	Instruction	Published	05/01/2023 8:26 AM
7364 - Insert power wires and use a small precision screwdriver to tighten the screw.	Remark	Published	05/11/2023 12:39 PM
7384 - 7365 - Reconnect Ethernet and fiber cables; Remark:7366	Procedure Step	Published	05/04/2023 4:28 PM
7365 - Reconnect Ethernet and fiber cables	Instruction	Published	05/11/2023 12:40 PM
7366 - Media Converter Connectors	Remark	Published	05/11/2023 12:40 PM
7279 - 7249 - Return equipment to normal operating condition; Remark:	Procedure Step	Published	04/27/2023 4:13 PM
7249 - Return equipment to normal operating condition	Instruction	Published	04/08/2025 3:22 PM
7386 - 7250 - Power on RPM; Remark:7367	Procedure Step	Published	09/01/2023 7:59 PM
7250 - Power on RPM	Instruction	Published	05/01/2023 8:31 AM
7367 - Move LD-260 switch to ON position. The PWR ON	Remark	Published	05/11/2023 12:42 PM
7387 - 7368 - Verify power and connectivity; Remark:7369	Procedure Step	Published	05/04/2023 4:31 PM
7368 - Verify power and connectivity	Instruction	Published	05/11/2023 12:42 PM
7369 - POWER and communications LEDs will be constantly on or blinking.	Remark	Published	05/10/2023 2:12 PM
7388 - 7304 - Confirm RPM has restarted correctly; Remark:7370	Procedure Step	Published	05/04/2023 4:32 PM
7304 - Confirm RPM has restarted correctly	Instruction	Published	05/01/2023 8:31 AM
7370 - The SC-770 will perform Power On Self-Test (POST) followed by a background me...	Remark	Published	05/10/2023 9:14 AM
7389 - 7254 - Confirm network connection; Remark:7255	Procedure Step	Published	05/04/2023 4:33 PM
7254 - Confirm network connection	Instruction	Published	04/27/2023 2:22 PM
7255 - Contact operators to confirm communications have been reestablished between RPM ...	Remark	Published	05/10/2023 3:15 PM
7390 - 7256 - Close and lock all RPM doors; Remark:	Procedure Step	Published	05/04/2023 4:34 PM
7256 - Close and lock all RPM doors	Instruction	Published	04/27/2023 2:21 PM
7842 - 7820 - Inform system operators upon completion of maintenance action; Remark:	Procedure Step	Published	07/07/2023 11:15 PM
7820 - Inform system operators upon completion of maintenance action	Instruction	Published	07/07/2023 10:02 PM
322 - 321 - Document maintenance actions; Remark:	Procedure Step	Published	06/17/2021 9:49 AM
321 - Document maintenance actions	Instruction	Published	04/21/2025 11:19 AM
2869 - 2585 - Document maintenance performed; Remark:2866	Procedure Step	Published	06/18/2021 5:58 PM
2585 - Document maintenance performed	Instruction	Published	07/09/2021 12:15 PM
2866 - Record observations, times, and results for the maintenance report.	Remark	Published	04/21/2025 11:39 AM
4706 - 4705 - Submit report; Remark:4864	Procedure Step	Published	06/29/2022 9:50 AM
4705 - Submit report	Instruction	Published	06/29/2022 9:50 AM
4864 - As specified by management or contractual obligations.	Remark	Published	07/28/2022 1:36 PM
Corrective Maintenance Procedure	Document Type	Published	03/02/2020 3:32 PM
Instrument is not functioning correctly	Frequency	Published	12/19/2022 5:52 PM
Warning	Annotation Type	Published	03/02/2020 3:25 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Caution	Annotation Type	Published	03/02/2020 3:24 PM
Technician 2	Skill Level	Published	04/09/2020 1:17 AM
Keys to access RPM	Replacement Parts	Published	04/27/2023 6:56 PM
Medium Phillips (PH2) screwdriver	Tools	Published	04/24/2020 4:40 PM
Small slotted precision screwdriver	Replacement Parts	Published	05/04/2023 4:38 PM
Orange/yellow safety vest	Replacement Parts	Published	04/27/2023 6:56 PM
Safety shoes	Replacement Parts	Published	04/27/2023 6:56 PM
Gloves	Replacement Parts	Published	05/10/2023 3:28 PM
Protective headwear: glasses, hard hat	Replacement Parts	Published	05/10/2023 3:31 PM
Orange traffic cones	Replacement Parts	Published	04/27/2023 6:56 PM
LD-260 Disconnect Switch Power Off	Image	Published	04/24/2023 12:49 PM
Magnum CS14P Premium Rated Converter Switch	Image	Published	05/04/2023 1:38 PM
Magnum CS14P Premium Rated Converter Switch Loosen Screw	Image	Published	05/04/2023 1:46 PM
Magnum CS14P Premium Rated Converter Switch Screws	Image	Published	05/04/2023 1:53 PM
Magnum CS14P Premium Rated Converter Switch Screws	Image	Published	05/04/2023 4:50 PM
Magnum CS14P Premium Rated Converter Switch Tighten Screws	Image	Published	05/04/2023 2:11 PM
Magnum CS14P Premium Rated Converter Switch Connectors	Image	Published	05/04/2023 3:31 PM
LD-260 Disconnect Switch Power On	Image	Published	05/04/2023 3:37 PM
Magnum CS14P Premium Rated Converter Switch LEDs.png	Image	Published	05/04/2023 3:41 PM

DET-RPM-RAP-CM12

Replace the ethernet-to-fiber media converter (GarrettCom Magnum CS14P) on the radiation portal monitor (RPM).

Equipment Hierarchy

Rapiscan PM-700 Pedestrian Monitor

Rapiscan VM-250 Vehicle Monitor

Rapiscan TM-850 Rail Monitor

Frequency

Instrument is not functioning correctly

Technician Level

Technician 2

x 1

Duration

Length of time

Tools Required

Keys to access RPM

Medium Phillips (PH2) screwdriver

Small slotted precision screwdriver

Orange/yellow safety vest

Safety shoes

Gloves

Protective headwear: glasses, hard hat

Orange traffic cones

Materials Required

GarrettCom Magnum CS14P media converter (Rapiscan Part #8590)

Originators

Craig Stinson

David Alexander

Melody Maynard

Brian Tucker

Originating Organization

ORNL; PNNL

Approver

Cody Hostick

Safety Concerns

Traffic

Final Documentation

Corrective Maintenance Report

Departmental Coordination

Prior to arrival, notify operators concerning expected work, duration, and anticipated alarms and fault indications.

Date of Origin

2021-07-01

Version

0.00

Preparation

Step 1

Main Step

7371 - 1401 - Establish Initial Conditions; Remark:

Step 00

1401 - Establish Initial Conditions

Establish Initial Conditions

7372 - 7231 - Close lane; Remark:7233

7261 - Warning : Traffic should temporarily be rerouted or halted during this procedure to ens...

Type

Warning

Traffic should temporarily be rerouted or halted during this procedure to ensure safety and prevent unscreened vehicles from passing.

Step 00

7233 - Use orange safety (traffic control) cones to setup barriers. Practice establi...

Use orange safety (traffic control) cones to setup barriers. Practice established safety protocols.

7373 - 7232 - Open RPM door; Remark:7267

Step 00

7267 - Open all doors needed to access components.

Open all doors needed to access components.

7374 - 7235 - Power off RPM; Remark:7236

Step 00

7236 - Move LD-260 switch to OFF position. The PWR ON

Move LD-260 switch to OFF position. The PWR ON LED will turn off.

Operation

Step 2

Main Step

7375 - 7356 - Uninstall Faulty Media Converter; Remark:

Step 00

7356 - Uninstall Faulty Media Converter

Uninstall Faulty Media Converter

7376 - 7357 - Disconnect Ethernet and optical cables; Remark:7358

5291 - Note : It is good practice to verify all cables and connectors are labeled prior to ...

Type

Note

It is good practice to verify all cables and connectors are labeled prior to disconnection.

Step 00

7357 - Disconnect Ethernet and optical cables

Disconnect Ethernet and optical cables

7358 - Magnum CS14P Premium Rated Converter Switch

Magnum CS14P Premium Rated Converter Switch

7377 - 7295 - Disconnect power wires; Remark:7359

Step 00

7359 - Use a small precision screwdriver to loosen the screw

Use a small precision screwdriver to loosen the screw

7378 - 5405 - Remove two (2) mounting screws; Remark:7360

Step 00

5405 - Remove two (2) mounting screws

Remove two (2) mounting screws

7360 - Use medium Phillips head (PH2) screwdriver. Retain screws.

Use medium Phillips head (PH2) screwdriver. Retain screws.

7379 - 7361 - Remove faulty media converter; Remark:

Step 00

7361 - Remove faulty media converter

Remove faulty media converter

3397 - 3395 - Label faulty component; Remark:3396

Step 00

3396 - Use tag or tape. Include date of removal, description of failure symptoms, co...

Use tag or tape. Include date of removal, description of failure symptoms, country, site, and lane number. Dispose per Nuclear Smuggling Detection and Deterrence (NSDD) guidance or contractual requirements.

Operation

Step 3

Main Step