CSECO K910G Buster Operation | FRONTLINE Maintenance Tool

Last Updated: 04/28/2025 1:42 AM

The following table lists all the components that make up the document.

Title	Type	Status	Last Updated
CSECO Buster K910G	Device	Published	10/28/2024 3:38 PM
10340 - 5919 - Calibrate Instrument; Remark:	Procedure Step	Published	12/01/2023 12:05 PM
10406 - Note : The buster needs to be calibrated before field use. This is to make sure that...	Annotation	Published	12/01/2023 1:47 PM
5919 - Calibrate Instrument	Instruction	Published	11/07/2022 1:22 PM
10339 - 10338 - Place buster on calibration block; Remark:	Procedure Step	Published	12/01/2023 12:06 PM
10338 - Place buster on calibration block	Instruction	Published	12/01/2023 12:06 PM
10376 - 10375 - Press and hold trigger; Remark:10374	Procedure Step	Published	12/01/2023 1:13 PM
10375 - Press and hold trigger	Instruction	Published	12/01/2023 12:31 PM
10374 -	Remark	Published	12/01/2023 1:13 PM
10380 - 10379 - Continue to press and hold trigger during entire calibration...; Remark:	Procedure Step	Published	12/01/2023 1:15 PM
10379 - Continue to press and hold trigger during entire calibration...	Instruction	Published	12/01/2023 1:15 PM
10381 - 10378 - Simultaneously press and hold Lock and Mode...; Remark:10377	Procedure Step	Published	12/01/2023 1:19 PM
10378 - Simultaneously press and hold Lock and Mode...	Instruction	Published	12/01/2023 1:17 PM
10377 - CSECO K910G Lock and Mode Buttons	Remark	Published	03/28/2024 1:19 PM
10384 - 10383 - Release Lock and Mode buttons; Remark:10382	Procedure Step	Published	12/01/2023 1:22 PM
10383 - Release Lock and Mode buttons	Instruction	Published	12/01/2023 1:21 PM
10382 - The buster will beep 10 times as it averages the calibration readings.	Remark	Published	12/01/2023 1:22 PM
10387 - 10386 - Press Mode button after the double beep; Remark:10385	Procedure Step	Published	12/01/2023 1:34 PM
10386 - Press Mode button after the double beep	Instruction	Published	12/01/2023 1:30 PM
10385 - This will store the updated calibration value. This number should be recorded...	Remark	Published	12/01/2023 1:34 PM
10389 - 10388 - Release trigger; Remark:	Procedure Step	Published	12/01/2023 1:35 PM
10388 - Release trigger	Instruction	Published	12/01/2023 1:35 PM
10396 - 10395 - Scan; Remark:	Procedure Step	Published	12/01/2023 1:39 PM
10395 - Scan	Instruction	Published	12/01/2023 1:39 PM
10393 - 10392 - Hold buster on surface of object to be scanned; Remark:	Procedure Step	Published	12/01/2023 1:40 PM
10392 - Hold buster on surface of object to be scanned	Instruction	Published	12/01/2023 1:40 PM
10394 - 220 - Power on instrument; Remark:10390	Procedure Step	Published	04/07/2025 2:38 PM
220 - Power on instrument	Instruction	Published	04/06/2025 7:00 PM
10390 - CSECO K910G Trigger Button	Remark	Published	04/10/2024 1:52 PM
10402 - 10401 - Keep trigger pushed in for two seconds; Remark:10400	Procedure Step	Published	12/01/2023 1:43 PM
10401 - Keep trigger pushed in for two seconds	Instruction	Published	12/01/2023 1:42 PM
10400 - This will allow the buster to normalize readings against background.	Remark	Published	12/01/2023 1:43 PM
10403 - 10399 - Keeping trigger pushed, slowly move buster over area; Remark:	Procedure Step	Published	12/01/2023 1:44 PM
10399 - Keeping trigger pushed, slowly move buster over area	Instruction	Published	12/01/2023 1:44 PM
10404 - 10398 - Observe values on display for any anomalies; Remark:	Procedure Step	Published	12/01/2023 1:44 PM
10398 - Observe values on display for any anomalies	Instruction	Published	12/01/2023 1:44 PM
10405 - 10397 - Release trigger when scan is complete; Remark:	Procedure Step	Published	12/01/2023 1:45 PM
10397 - Release trigger when scan is complete	Instruction	Published	12/01/2023 1:45 PM
Operator Procedure	Document Type	Published	03/02/2020 3:31 PM
Note	Annotation Type	Published	03/02/2020 3:25 PM
Calibration block	Tools	Published	12/01/2023 12:03 PM
CSECO K910G Trigger Button	Image	Published	12/01/2023 1:13 PM
CSECO K910G Lock and Mode Buttons	Image	Published	12/01/2023 1:19 PM
CSECO K910G Mode Button	Image	Published	12/01/2023 1:33 PM

DET-HHD-CSC-OP01

Use the K910G buster to search for contraband

Equipment Hierarchy

CSECO Buster K910G

Technician Level

Duration

Tools Required

Calibration block

Originators

Erica Demboski

Originating Organization

PNNL

Approver

Deena Bean

Date of Origin

2020-01-01

Version

0.00

Operation

Step 1

Main Step

10340 - 5919 - Calibrate Instrument; Remark:

10406 - Note : The buster needs to be calibrated before field use. This is to make sure that...

Type

Note

The buster needs to be calibrated before field use. This is to make sure that it is working and reading properly. Calibration should be done every time it is taken into a new environment and on a regular monthly basis.

If you wish to check the buster’s reading after calibrating, place the buster back on the calibration block and push in the trigger. The display should show “100” as the reading. It may not stay at “100,” but as long as you see “100” it is working properly.

Step 00